• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.117-117
• /
• 2004

일반적으로 접촉 피로 마멸은 구름 또는 미끄럼 접촉시 작용하는 반복 응력에 의해 표면과 표면 아래에 균열이 형성되고 성장 및 합체의 과정을 거쳐 표면의 일부가 떨어져 나가는 손상으로 기어나 캠-롤러, 구름 베어링과 같이 구름-미끄럼 접촉상태로 운전하는 기계요소에서 가장 중요하게 고려되어야 할 파손 메커니즘이다. 특히 기어나 구름 베어링 같이 고주기 접촉 피로 특성을 지니는 기계요소의 수명은 피로수명 실험과 통계적 기법을 이용한 Weibull 이론을 기초로 한 수명식을 대부분 사용하고 있다.(중략)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1269-1276
• /
• 2001

In case of contact fatigue, the accurate calculation of surface tractions and subsurface stress is essential to the predication of crack initiation life. Surface tractions influencing shear stress amplitude have been obtained by contact analysis based on influence function. Subsurface stress has been obtained by using rectangular patch solutions. In this study, to simulate asperity contact under sliding condition, the tip of asperity was simulated by sphere and to calculate crack initiation life in the substrate, dislocation pileup theory was used.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.10a
• /
• pp.163-167
• /
• 1996

The life of rolling elements depends on various factors such as operating conditions and material properties. In this work, the effect of microstructure on the rolling behavior is investigated. Specially, the deformations in the substrate regions before and after rolling are compared. It is found that rolling action causes severe flow of material in the direction opposite to the rolling direction in the case of dry rolling direction. With lubrication, the deformation is more severe at the subsurface region rather than at the surface.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2019-2028
• /
• 1997

It has been well established that resistant force and wear that occur during rolling motion depend on several factors such as material type, hardness, subsurface microstructure, applied load, and speed. The purpose of this work is to investigate the effect of microstructure and the state of deformed layer on the rolling contact characteristics in dry and lubricated rolling contacts. The results of this work show that the rolling resistance behavior depends on the state of the deformed layer. Also, lubrication can reduce the plastic flow at the surface but may still have an effect on the subsurface strain. The cross-sectional view of the microstructure shows that surface traction has a difinite effect on the morphology of the surface region. That is, significant slip seems to have taken place between the ball than those of the dry rolling case. The surface generation effects were significantly less compared to the case of dry rolling contact.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.06a
• /
• pp.31-36
• /
• 2000

평면연삭은 기계부품의 후가공 공정에 사용되며, 기계부품의 다듬질면은 내마멸성, 피로강도 및 내식성등 품질에 큰 영향을 미친다. 연삭작업중 가장 큰 위험 요소는 고속작업중 연삭숫돌의 파손이다. 연삭숫돌의 파괴되는 주요 원인은 고속 회전중 최고사용 원주속도를 넘어 지나치게 빠를 때 원심력이 결합력보다 커지는 경우와, 숫돌에 균열(crack)이 있을 때이다. 연삭숫돌이 파괴되어 숫돌 파편이 작업자의 머리, 안면등을 강타하여 사망이나 골절등 중대재해가 발생된다. (중략)

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1995.06a
• /
• pp.25-30
• /
• 1995

본 연구에서는 건식 구름접촉시 발생하는 tribological한 현상들을 plate on ball tester를 이용하여 실험적으로 고찰하였다. 실험의 주된 관심은 각 열처리 방법으로 제작한 시편에 대하여 건식 구름접촉시 cycle수에 따른 plate의 표면 거칠기, 트랙의 형상, 졍도 및 구름저항의 변화이며 이런 자료를 토대로 열처리공정의 차이에서 오는 정도수명 및 피로수명에 대한 상대평가를 통해 마찰, 마멸의 저감에 적합한 열처리방법을 제시하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.161-166
• /
• 2010

Elastomeric seals are widely used in dynamic seal applications, and it is well known that the sealing surfaces can be gradually worn out. Abrasive wear is known to be the most dominant factor; however, little research has been carried out on this problem until now. In this study, a new contact problem related to elastomeric seals-a small spherical particle and steel surface-was modeled and analyzed using MARC. Variations of von-Mises and residual stress distributions as well as deformed seal and steel surface shapes with seal materials and interferences are presented. The stress distribution and surface deformation are highly affected by the elastic properties of seal. For PTFE, the maximum von-Mises stress exceeds the yield strength, and plastic deformation occurs on the steel surface. Therefore, the sealing surface can also be worn down by sub-surface fatigue due to intervening hard particles in the sealing surfaces together with the well-known abrasion.