• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.1-11
• /
• 2000

Instantaneous temperature probes were manufactured by pressing method. By using these probes, the instantaneous surface temperature and unsteady heat flux in the cylinder liner of DOHC engine were measured. The main results are as follows; ⅰ) the instantaneous surface temperature of cylinder liner are affected by the contact of piston ring as well as burning gas. ⅱ) the wall temperature of the siamese portion is much higher than other parts. ⅲ) it was shown that the rising trend of heat flux by burning gas are nearly limited to the 1/2-stroke distance from the top of cylinder liner.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.196-204
• /
• 1998

For the experimental measurement of instantaneous surface temperature of the piston of the DI mono cylinder diesel engine, the instantaneous temperature proves, data acquisition system, and grass-hopper type linkage system were developed. The instantaneous temperatures on the piston bowl, crown, lands and skirt were measured and analyzed, and the following conclusions were derived ; (i) The crank angle for the maximum instantaneous temperature during one cycle varies and moves back and forth by the measuring positions and engine speeds. (ii) The engine speeds, the positions of the measuring points and the cooling water temperature had an effect on the instantaneous temperature amplitude. (iii) The instantaneous temperature suing phenomena appeared on the temperature profiles of the piston crown, top and second land of ring, but on the temperature profiles of the parts of the third land of the fing and skirt, they didn't appear, (iv) The isothermal lines in the piston were acquired through the operation of the finite elements method using the measured temperatures as the boundary conditions.

• Proceedings of the KAIS Fall Conference
• /
• 2009.05a
• /
• pp.870-873
• /
• 2009

본 연구에서는 미세 무광부식 패턴을 갖는 HD Switch Panel 부품을 설계하고 금형을 제작하였다. 이를 위하여 사출성형 Simulation(CAE)을 이용하여 사출성형 공정의 문제점과 부품의 변형량을 예측 하였다. 또한 금형표면의 가열온도와 실제 금형온도의 비교함으로써 공정변수 조절을 통한 사출성형 조건의 최적화를 달성할 수 있었다. 한편, 순간금형표면가열을 이용한 성형기술인 E-MOLD를 적용하여 자동차 내장부품용 HD Switch Panel을 제작하였고, 전자현미경과 원자현미경을 이용한 표면 평가를 통하여 무광부식 패턴의 전사율 향상으로 인한 무광 특성이 향상됨(2.5이상$\rightarrow$1.5~1.7)을 확인하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.178-187
• /
• 1997

For the experimental measurement of heat flux of DI diesel engine combustion chamber, the instantaneous temperature probes and data acquisition system were developed. By the analysis of measured temperatures at the cylinder head, the temperature at the point 3 which is located between intake and exhaust valve was higher than that of the other points. Temperatures at the point located mear the exhaust valve were higher than those of intake valve. The instantaneous and mean temperature at the cylinder head increases proportionally to the increase of the engine speed, while the temperature swing varies inversely. Temperature swings have influence on the maximum heat flux values from gas into head surface. It has been verified that these probes and data acquisition system perform well by the comparison of the trend of instantaneous temperature variation with that of measured combustion chamber pressure variation with respect to crank angle. It is presumed that these probes could be used in the measurement of other parts of combustion chamber as piston, cylinder wall etc. for the future study.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.4
• /
• pp.267-275
• /
• 2001

To clear the differences of heat transfer coefficient of in-cylinder gas with fuel properties, the transient heat transfer coefficient of hydrogen gas is investigated by using the hydrogen fueled engine. The measured results were also compared with those of gasoline engine and several empirical equations. Transient heat transfer coefficients were determined by measurements of unsteady heat flux and instantaneous wall temperature in the cylinder head. As the main results, it is shown that transient heat transfer coefficients have remarkable differences according to fuel properties, and it's value for hydrogen engine is twice higher than that of gasoline engine. It means that equation of heat transfer coefficient that the effect of fuel properties is considered sufficiently, is needed to analyze or simulate the gas engine performance.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1988.06a
• /
• pp.28-30
• /
• 1988

윤활시스템에서 마모는 상대적인 운동을 하는 두 물체사이에서 표면상태, 접촉조건 및 분위기등의 제요소들에 의해 발생되며, 형태학적으로 scuffing, scoring, pitting 및 fretting 등으로 분류된다. 윤활조건의 특성에 따라 미끄럼 접촉에서는 mild wear, severe wear로 구분되며, 이들의 마모 생성기구의 차이는 접촉상대속도, 하중 및 표면조도등의 정도에 기인된다. mild wear에서 severe wear 영역으로 전이될 때의 가혹한 조건에서 생성되는 마모현상을 scuffing wear라 하며, 이는 접촉면에서의 표면돌기의 직접접촉에 의한 cold welding 현상, 즉 local welds의 특성을 지닌 마멸형태로 정의한다. 이의 생성은 접점간의 하중 및 미끄럼 속도가 증가됨에 따라 온도상승에 기인되어 순간적으로 발생된 마찰열이 그 원인이 있으며, 기어, cam 및 tappet, 피스톤링 및 실린더 라이너 등의 마멸현상이 대표적인 예이다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.11
• /
• pp.1466-1474
• /
• 1997

In order to design and develop a spark ignition engine, many studies must be preceded about the characteristics of thermal flow. For measurement of transient wall temperature thin film thermocouples of Bendersky type were manufactured and these probes were fixed into the wall of combustion chamber. Surface wall temperatures were measured in experiments of various engine speeds. Transient heat fluxes were calculated from the wall temperature measurements. Pressure was measured from combustion chamber using pressure transducer and gas temperatures were calculated using the state equation of ideal gas. And instantaneous heat transfer coefficients were obtained. It will be the basic data for the formulae of instantaneous heat transfer coefficients.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.208-217
• /
• 1996

Instantaneous surface temperature and unsteady heat flux of intake and exhaust valve in methanol fueled engine were investigate as a function of compression ratio and engine speed. To accomplish this purpose, the instantaneous temperature sensor was designed and it was installed into three point of intake and exhaust valve head to measure unsteady temperature. The unsteady heat flux at valves was evaluated using one dimensional heat conduction equation with the valve head temperature and temperature gradient. And also mean heat flux of intake and exhaust valve for each stroke were evaluated as a function of engine speed.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.60-66
• /
• 1990

In order to measure the piston surface temperature and heat flux, autors have developed the measuring system with an instantaneous temperature probe. Such the instantaneous temperature probes were embodied into the top of piston for measurement and L-link system, designed to fit the test engine, extracts the thermocouple wires from the piston outside of engine employing a mechanical linkage. Then the instantaneous surface temperature was measured to calculate the heat flux flowing into the top surface of piston in a spark ignition engine. As a result, the following phenomena have been obtained through the study. 1) It is found that the time response and durability of temperature probe with a thin film thickness 10um and mechanical linkage with thermocouple wire extraction is sufficient at this experiment. 2) For the quantitative effect of variation in engine speed, the temperature swing and heat flux on the top of piston increase with increasing the engine speed. 3) It is proved that the temperature swing and heat flux decrease with distance from spark plug.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3280-3286
• /
• 2009

In this paper, we designed and manufactured HD Switch Panel parts with micro-etched pattern. By using CAE analysis, we could predict weld-line positions and the amount of shrinkage during injection molding process. We measured the temperature distribution of the mold surface so that we could optimize the processing conditions such as mold temperature. In order to increase the transcription of micro-etched pattern, we applied the E-Mold technology and evaluated the effect of mold temperature on the surface quality. We concluded that the etched pattern was improved(more than 2.5$\to$1.5~1.7) through the measurement of surface gloss and the observation of both SEM and SPM images.