• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.73.3-74
• /
• 2016

본 연구에서는 비구면 반사경의 형상오차를 3가지 방법으로 측정, 비교하였다. 실험에 사용한 포물면 반사경의 구경은 108 mm, 유효초점거리는 444.5 mm 이다. 첫 번째로 접촉식 형상측정방식인 FTS(Form TalySurf)를 이용하여 표면 거칠기와 반사경의 최적 곡률 반경(BestFitt Radius) 값을 측정하였다. 두 번째로는 비접촉식 형상측정방식인 UA3P(Ultrahigh Accurate 3-D Profilometer)를 이용하여 반사경의 형상 정밀도를 측정하였다. UA3P를 이용할 경우 반사경의 전체 형상을 측정할 수 있다. 세번째로 Shark-Hartmann 센서를 이용한 광학측정방법으로 반사경의 형상 정밀도를 측정하였다. 측정에 필요한 레이저 광학계는 레이저, 콜리메이터, 핀홀, 카메라 렌즈 및 비구면 광학계를 이용하여 설계하였다. 본 연구에서 도출한 각 측정 방법의 신뢰도를 바탕으로 간섭계 사용에 제약이 있는 자유형상곡면의 반사경 표면의 형상오차 측정에 적용할 계획이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.618-627
• /
• 2016

This study numerically analyzes the characteristics of the velocity distribution for each location of a square-sectional $180^{\circ}$ bent duct using a Reynolds Stress Turbulent model. The flow parameters were varied, including the working fluids, inlet velocity, surface roughness, radius of curvature, and hydraulic diameter. The boundary conditions for computational fluid dynamics analysis were inlet temperatures of air and water of 288 K and 293 K, inlet air velocity of 3-15 m/s, inner surface roughness of 0-0.001 mm, radius of curvature of 2.5-4.5 D, and hydraulic diameter of 70-100 mm. The working fluid characteristics were highly affected by changes in the viscous force. The maximum velocity profiles in the bent duct were indicated when the $90^{\circ}$ section was in the region of X/D=0.8 and the $180^{\circ}$ section was in the region of Y/D=0.8. Lower surface roughness and higher radius of curvature resulted in a higher rate of velocity change. Also, an efficient measuring location downstream of the bent duct is suggested since the flow deviations were the most stable when the straight duct length was in the region of L/D=30. The minimum deviations at the same velocity conditions according to the hydraulic diameter were mostly indicated in the range of L/D=15-30 based on the standard deviation characteristics.

• Proceedings of the IEEK Conference
• /
• 2003.07e
• /
• pp.2263-2266
• /
• 2003

Three-dimensional face recognition algorithm using curvature information representing characteristics of surface form is suggested. The experiment showed more than 90 percent of recognition for the noses which had definite change value of data, and contained much information about surface curvature. Recognition ratio using a contour taken from the remaining part other than the eyes, noses, mouths which are the main components of faces showed the important role, which could be used as the important index information in the three-dimensional face recognition.

• Proceedings of the KAIS Fall Conference
• /
• 2006.05a
• /
• pp.112-115
• /
• 2006

본 논문에서는 무인 생산 공정의 선삭 가공 시 발행하는 칩의 처리에 관한 연구를 수행하였다. 선삭시 발생되는 칩은 부품의 정밀도와 표면 조도를 저하시키는 등 품질 저하와 함께 생산성을 저해하는 요소가 되기도 한다. 이러한 칩을, 칩 브레이커를 사용하여 작은 곡률 반경으로 절단함으로써 칩 제거를 효율적으로 제어한다. 그와 함께, 다구찌 기법을 적용하여 최적의 조건으로 칩 브레이커 형상 설계 인자를 도출하는데 그 목적이 있다.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.1
• /
• pp.55-62
• /
• 2009

Blast cleaning has been applied in steel bridges for cleaning forged surface and increasing adhesive property of applied coating systems. Blasting is the operation of cleaning or preparing a surface by forcible propelling a stream of abrasive metals against it. Blast cleaning may improve surface geometry and induce compressive residual stress, and eventually may increase fatigue life of weld joints. In this paper, fatigue tests were carried out on three types of non-load-carrying fillet welded cruciform joints, as-welded joints, blast-treated joints, and stress-relieved joints after blasting, in order to investigate effect of blast cleaning on fatigue behavior of the weld joints. By Blast cleaning, the weld toe radius was increased by 29% and compressive residual stress was induced near weld toes. Blast cleaning increased fatigue life and fatigue endurance limit of the weld joints. When the applied stress ranges decreased, the increment in fatigue life became larger. About a 150% increase in fatigue limit could be realized by using blast cleaning.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.523-528
• /
• 2013

In this experiment, we investigated the performance of two types of heat sink, swaged- and extruded-type, used in the inverter of industrial electricity generator. The swaged-type heat sink has 62 fins, and the extruded-type has 38 fins having the same dimension as that of the swaged-type. But the extruded-type heat sink maintains the same heat transfer area by the laterally waved surface which has 1 mm in radius. As a result, the swaged- and extruded-type heat sinks released 70.7% and 63.8% of the heat incoming to the heat sink, respectively. The other incoming heat were naturally convected and radiated to the ambient. In spite of 40% decrease in number of fins, the heat release performance of the extruded-type heat sink was lowered only 6.9% than that of the swaged-type. We believe that, this shows the increment of effective heat transfer area by the laterally waved surface of fins and the better heat transfer property of the extruded-type heat sink.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.11
• /
• pp.927-933
• /
• 2012

The characteristics of two-dimensional supersonic coanda flow was experimentally investigated. For various ratios of slot height to coanda wall's radius of curvature, surface roughnesses, and jet stagnation pressures, the characteristics of the supersonic coanda flow such as shock structures and hysteresis were observed by flow visualization. It was found that the characteristics of hysteresis of the coanda jet was related to the surface roughness of the coanda wall. The study was further extended for application of the tangentially injected coanda jet to control co-flowing highly compressible main jet direction. It was noticed that the stagnation pressure of the main jet as well as the ratio of the slot height to coanda wall's radius of curvature wall was an influencing factor in the performance of the fluidic thrust vectoring method.

• Journal of the Korea Computer Graphics Society
• /
• v.16 no.2
• /
• pp.29-37
• /
• 2010

In this paper, we present a novel deformation method for alleviating the asymmetry of a scanned 3D face considering facial features. To handle detailed areas of the face, we developed a new local 3D shape descriptor based on facial features and surface curvatures. Our shape descriptor can improve the accuracy when deforming a 3D face toward a symmetric configuration, because it provides accurate point pairing with respect to the plane of symmetry. In addition, we use point-based representation over all stages of symmetrization, which makes it much easier to support discrete processes. Finally, we performed a statistical analysis to assess subjects' preference for the symmetrized faces by our approach.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.1
• /
• pp.68-79
• /
• 2009

It is inevitable to have cutting line to get the 2D pattern from 3D body surface. In this paper the efficiency of curvature plot as a cutting line in the process of flattening 3D surface was investigated. As reference, basic clothing construction line was adopted to divide the 3D surface into small blocks to make the flattening process easy. Female dummy as well as human body were scanned and surface of the upper body was segmented using curvature plot and basic constructing line. 2D tight-fit pattern was developed using three software, the RapidForm 2004, 2C-AN and Yuka CAD. Gap between clothes and body, and the clothing pressure on the body was observed to determine the fit of the clothes. As results, clothes constructed with blocks divided by curvature plot displayed a similar level of tight fit as compared with those by basic construction line. It was found that curvature plot is effective method as a segmentation of the 3D surface even for the actual body which does not have any previous reference line. It is expected that application of curvature plot will be expanded in 3D apparel technology.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.10
• /
• pp.924-931
• /
• 2015

When a target locates at low altitude over a curved earth surface and far away from a radar, we examine the accuracy of the conventional formulations to compute the radar echo signal. The 4-ray model is used to calculate the scattering by the target to consider the ground plane effect. In this paper, the diffracted wave is not included. Based on the required parameters able to be calculated by known equations for the estimation of the wave propagation phenomena, the radar echo signal is computed and verified by comparing with measured data sets.