• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.28-38
• /
• 1981

A survey has been conducted to investigate the presents of breaks down and repair of power tiller for efficient use. Eight provinces were covered for this study. The results are summarized as follows. A. Frequency of breaks down. 1) Power tiller was breaken down 9.05 times a year and it represents a break down every 39.1 hours of use. High frequency of breaks down was found from the fuel and ignition system. For only these system, the number of breaks down were 2.02 and it represents 23.3% among total breaks down. It was followed by attachments, cylinder system, and traction device. 2) For the power tiller which was more than six years old, breaks down accured 37.7 hours of use and every 38.6 hours for the power tiller which was purchased in less than 2 years. 3) For the kerosene engine power tiller, breaks down occured every 36.8 hours of use, which is a higher value compared with diesel engine power tiller which break down every 42.8 hours of use. The 8HP kerosene engine power tiller showed higher frequency of break down compared with any other horse power tiller. 4) In October, the lowest frequency of break down was found with the value of once for every 51.5 hours of use, and it was followed by the frequency of break down in June. The more hours of use, the less breaks down was found. E. Repair place 1) 45.3% among total breaks down of power tiller was repaired by the owner, and 54.7% was repaired at repair shop. More power tiller were repaired at repair shop than by owner of power tiller. 2) The older the power tiller is, the higher percentage of repairing at the repair shop was found compared with the repairing by the owner. 3) Higher percentage of repairing by the owner was found for the diesel engine power tiller compared with the kerosene engine power tiller. It was 10 HP power tiller for the kerosene power tiller and 8 HP for the diesel engine power tiller. 4) 66.7% among total breaks down of steering device was repaired by the owner. It was the highest value compared with the percentage of repairing of any other parts of power tiller. The lowest percentage of repairing by owner was found for the attachments to the power tiller with the value of 26.5%. C. Cause of break down 1) Among the total breaks down of power tiller, 57.2% is caused by the old parts of power tiller with the value of 5.18 times break down a year and 34.7% was caused by the poor maintenance and over loading. 2) For the power tiller which was purchased in less than two years, more breaks down were caused by poor maintenance in comparison to the old parts of power tiller. 3) For the both 8-10 HP kerosene and diesel engine power tiller, the aspects of breaks down was almost the same. But for the 5 HP power tiller, more breaks down was caused by over loading in comparison to the old parts of power tiller. 4) For the cylinder system and traction device, most of the breaks down was caused by the old parts and for the fuel and ignition system, breaks down was caused mainly by the poor maintenance. D. Repair Cost 1) For each power tiller, repair cost was 34,509 won a year and it was 97 won for one hoar operation. 2) Repair cost of kerosene engine power tiller was 40,697 won a year, and it use 28,320 won for a diesel engine power tiller. 3) Average repair cost for one hour operation of kerosene engine power tiller was 103 won, and 86 won for a diesel engine power tiller. No differences were found between the horse power of engines. 4) Annual repair cost of cylinder system was 13,036 won which is the highest one compared with the repair cost of any other parts 362 won a year was required to repair the steering device, and it was the least among repair cost of parts. 5) Average cost for repairing the power tiller one time was 3,183 won. It was 10,598 won for a cylinder system and 1,006 won for a steering device of power tiller. E. Time requirement for repairing by owner. 1) Average time requirements for repairing the break down of a power tiller by owner himself was 8.36 hours, power tiller could not be used for operation for 93.58 hours a year due to the break down. 2) 21.3 hours were required for repairing by owner himself the break down of a power tiller which was more than 6 years old. This value is the highest one compared with the repairing time of power tiller which were purchased in different years. Due to the break down of the power tiller, it could not be used for operation annually 127.13 hours. 3) 10.66 hours were required for repairing by the owner himself a break down of a diesel engine power tiller and 6.48 hours for kerosene engine power tiller could not be used annually 99.14 hours for operation due to the break down and it was 88.67 hour for the diesel engine power tiller. 4) For both diesel and kerosene engine power tiller 8 HP power tiller required the least time for repairing by owner himself a break down compared with any other horse power tiller. It was 2.78 hours for kerosene engine power tiller and 8.25 hours fur diesel engine power tiller. 5) For the cylinder system of power tiller 32.02 hours were required for repairing a break down by the owner himself. Power tiller could not be used 39.30 hours a year due to the break down of the cylinder system.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.6
• /
• pp.21-28
• /
• 2007

The objective of this study was to investigate the effect of hydraulic retention time (HRT) on removal efficiencies of organic matter, nitrogen and phosphorus in MBR-RO process for treating synthetic sewage. In MBR process, turbidity was less than average 2 NTU and average removal efficiency showed more than 99% during the operation period(MBR 105 day). As a result of HRT variation, average removal efficiencies of $COD_{Cr}$ on HRT 6, 12, 18 and 24hour were about 72.4, 84, 88.6 and 92.5%, respectively. The $NH_4{^+}-N$ removal efficiency was about 60.2 85.5, 91.3 and 92.2%, respectively. T-N and T-P removal efficiencies increased from 53.7 and 56.8 to 82.5 and 86.4%, respectively as the HRT increased from 6 hour to 24 hour. In RO process, average removal efficiencies of color and $COD_{Cr}$ in RO permeate were about 99.9% and 96.8%, respectively. Also, removal efficiencies of T-N, $NH_4{^+}-N$, $NO_3{^-}-N$ and T-P were all above average 90%.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.310-310
• /
• 2011

본 연구에서는 금강의 평수기 하류 평균도달시간을 산정하고 이를 통해 이수, 치수, 환경적인 측면을 고려하여 유역의 유하량별 하류지점의 도달시간을 실측하고, 측정 자료를 근거로 하여 수학적모델링을 통해 지류 및 본류의 시나리오별 유출량-평균도달시간 관계를 분석하여 수자원의 개발 이용과 보전, 관리를 위한 기초자료를 제공하고자 하였다. 이를 위해 하천 전 구간에서 실측할 수 있는 센서기술을 활용하였으며, 활용한 센서부자를 이용하여 금강의 금남보~공주대교 구간에 대하여 계측을 수행하였다. 계측결과 유출량-평균도달시간에 영향을 미치는 요인으로는 하상경사, 하폭, 지류유입량, 강우량, 식생, 하천구조물 등이 있으며, 이러한 요인을 수리학적 모형을 적용하여 모든 사상에 대해 정확한 해석을 한다는 것은 매우 어려운 일이다. 이로 인해 유출량-평균도달시간과의 관계 분석을 위해서는 많은 계측이 수반되어야 하며, 계측 결과를 토대로 각 하천별 유출량별 평균도달시간 관계에 대한 정확한 해석 방법을 제안하고자 하였다. 본 연구의 계측결과는 평 갈수기 수질사고로 인한 위기상황 대처시 도달시간 참조 자료로 활용이 가능할 것이며, 향후 지속적인 예측을 위해 수치모형의 매개변수를 보정하여 신뢰성 높은 도달시간표 제작이 가능하다. 또한, 기존 홍수예보 자료를 보완할 수 있는 유비쿼터스 기반 실측기술을 개발하고 이를 적용할 수 있는 기반을 구축함으로써 홍수예보의 신뢰성을 확보하고 홍수기댐 운영의 효율성을 확보할 수 있을 것으로 기대된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.477-477
• /
• 2017

국내 4대강사업 이후의 하천환경의 변화를 고려한 보 구간 별 도달시간 재산정이 필요하며, 더욱이 다기능 보의 영향을 고려한 도달시간에 대한 연구도 필요한 실정이다. 또한 4대강사업 이후 설치된 다기능 보의 기존 방류를 이용한 보 운영은 관리수위를 유지하기 위해 유입된 수량만을 방류시켜 수온차가 있는 성층파괴에는 한계가 있었다. 이러한 문제점으로 펄스 방류는 수질개선을 위하여 제시된 인위적 반복적 방법으로 하천의 유량 및 유속을 증대시켜 하천 상 하층을 혼합하여 성층을 파괴함으로써 조류의 성장을 억제하기 위한 목적으로 적용될 수 있으며, 실제 하천에 적용하기에 앞서 보 방류조건에 따른 흐름전달특성의 분석과 검증이 필요하다. 이에 본 연구에서는 4대강사업 이후의 하도에 대한 지형자료와 상세한 보주변의 지형자료를 이용하여 수리학적 모형을 위한 하도자료를 구축하였으며, 보 운영을 고려하여 2차원 수리해석을 실시하였다. 보 방류조건에 따른 흐름전달특성 분석에 앞서 각 보 구간별 거리를 산정하였다. 또한 일정 방류 시나리오 유량조건을 이용하여 각 보 구간별 도달시간을 산정하였으며, 산정된 도달시간은 HEC-RAS를 통해 모의된 계산결과와 비교 및 한국수문조사연보 유량편의 평균유속과의 비교 및 검증을 실시하였다. 또한 펄스 방류에 따른 흐름의 전달특성을 분석을 하였으며, 분석한 결과와 보 하류 주요지점에서의 수위 관측결과를 2차원 수리모형에서 확인 할 수 있었다. 또한 2차원 수리모형 내에서 입자를 적용하여 입자추적을 통한 보 하류부의 흐름전달 양상을 해석하였다. 본 연구를 통하여 유량 규모 및 등급별 방류량을 고려하여 적용 가능한 간편 도달시간을 제안 및 산정하여 현장에서 실무적으로 사용가능한 자료를 제공함으로써 하천 유지 및 관리에 이용이 가능할 것이라 판단된다. 또한 펄스 방류에 따른 흐름의 전달특성을 분석함으로써, 특정 방류량에 따른 흐름특성을 이해하고 후에 수질개선 효과 분석 및 다양한 방류시나리오에 따른 보의 운영 지침에 기초자료를 제공할 수 있을 것으로 판단된다.

• The Korean Journal of Applied Statistics
• /
• v.11 no.1
• /
• pp.53-64
• /
• 1998

Recently, it is of great interest among engineers and reliability scientists to consider a statistical model to describe the failure times of various types of repairable systems. The main subject we deal with in this paper is the power law process which is proved to be a useful model to describe the reliability growth of the repairable system. In particular, we derive the bootstrap confidence intervals of the mean time between two successive failures of a repairable system using the time truncated data. We also compare our bootstrap confindence intervals with Crow's (1982) confidence interval.

• Economic and Environmental Geology
• /
• v.38 no.1
• /
• pp.79-89
• /
• 2005

Groundwater level changes in coastal aquifers occur due to oceanic tides, where the properties of oceanic tides can be applied to estimate hyadraulic parameters. Hydraulic parameters of coastal aquifers located in eastern part of Jeju island were estimated using the tidal response technique. Groundwater level data from a saltwater intrusion monitoring well system was used which showed tidal effects from 3 to 5 km. The hydraulic gradient was assessed by utilizing the filtering method from 71 consecutive hourly water-level observations. Calculated hydraulic diffusivity ranged from 2.94${\times}10^7m^2d^{-1}$ to 4.36${\times}10^7m^2d^{-1}$ . The hydraulic gradient of the coastal aquifer area was found to be ~$10^{-4}$, whereas the gradient of the area between wells Handong-1 and 2 was found to be ~$10^{-6}$, which is very low comparatively. Analysis of groundwater monitoring data showed that groundwater levels are periodically higher near coastal areas compared to that of inner land areas due to oceanic tide influences. When assessing groundwater flow direction in coastal aquifers it is important to consider tidal fluctuation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.2
• /
• pp.180-185
• /
• 1999

Rotating Biological Contactor (RBC) was tested for the treatment of artificial rearing water in n simulated aquaculture system. Performance of RBC on the removal of TAN and COD was evaluated by controlling hydraulic residence time (HRT). As HRT of RBC was increased, TAN removal rate ana removal efficiency of RBC and TAN concentration of rearing water were increased, but COD removal rate was decreased. Total alkalinity consumption rate was increased by increasing HRT of RBC. Ratio between total alkalinity consumption rate and TAN removal rate was 7.73. HRT for maintaining lowest TAN and COD concentration of artificial rearing water was 14,6 minutes and at that condition TAN and COD concentration of the water was 1.28 and $5.59 g/m^3$, respectively.

• 대한공업교육학회지
• /
• v.33 no.2
• /
• pp.248-258
• /
• 2008

Current Internet uses HTTP (Hyper Text Transfer Protocol) as an application layer protocol and TCP (Transmission Control Protocol) as a transport layer protocol to provide web service. SCTP (Stream Control Transmission Protocol) is a recently proposed transport protocol with very similar congestion control mechanisms as TCP, except the initial congestion window during the slow start phase. In this paper, we present a mathematical model of object transfer latency during the slow start phase for HTTP over SCTP and compare with the latency of HTTP over TCP. Validation of the model using experimental result shows that the mean object transfer latency for HTTP over SCTP during the slow start phase is less than that for HTTP over TCP by 11%.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.23 no.2
• /
• pp.36-52
• /
• 2020

This study performed 2-D(two-dimensional) hydrodynamic analysis using EFDC in the Nakdong River. For the simulation of the flood season and non-flood season, the measured data including water level, weir outflow and tributary inflow were used, and the accuracy and applicability of the model were verified by comparing the measured water level and computed one. In addition, statistical quantitative assessment of the model performance was performed by estimating PBIAS, RSR, and RMSE for the computed water level. Then, the average velocity for each section between weirs was calculated by applying constant discharge conditions, and it was compared and verified with the measured velocity by Hydrological Survey Center. In this study, a simple method for estimating the arrival time was proposed, and it is expected that it will be practically applicable in field practices such as flood forecasting and warning.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.426-430
• /
• 2009

본 연구에서는 ADCP 측정자료를 효율적으로 활용할 수 있도록 ADCP 이동측정법 자료의 후처리 프로그램을 개발하였다. 먼저, 측정된 ensemble과 방위별 유속으로 표시되던 단면유속분포를 한 눈에 알아볼 수 있도록 좌표를 정리하고 주흐름방향 유속을 출력하는 등, Sontek과 RDI 자료 취득 소프트웨어의 ascii 파일을 사용자가 쉽게 알아보고 가공할 수 있도록 변형하였다. 또한, 기존 ADCP 사용과 관련하여 발표된 screening 및 smoothing 기법을 적용하여 유효한 유속자료를 선별하고 단면의 평균 흐름에 근접한 유속자료를 제공하도록 하였다. 멱함수를 이용한 외삽으로 측정불가역의 유속 및 유량을 추정하였으며, 총 53개 측정자료의 유량을 추정한 결과 ADCP 소프트웨어가 제공하는 유량과 평균 1.33 %의 오차를 보였다. 마지막으로, 정리된 ADCP 자료로부터 하천의 주요 수리학적 특성을 추정하도록 하여 하천단면을 횡단하는 간단한 ADCP 측정만으로도 많은 시간과 노력을 들여 측정하던 하천의 특성을 신속히 파악할 수 있도록 하였다.