• Economic and Environmental Geology
• /
• v.40 no.6
• /
• pp.833-841
• /
• 2007

The groundwater heat pump system(GWHP) is one of the most efficient ground source heat pump system(GSHP) which uses low grade and shallow geothermal energy for cooling and heating purpose. The GWHP system shall be designed properly based on peak block load performance and optimum pumping rate of groundwater comparable to ground coupled heat pump system(GCHP). The optimum pumping rate depends on groundwater temperature at a specific site, size of plate heat exchanger, and total head loss occurred by whole system comprising pumps and pipings. The required optimum flow rates of the system per RT are ranged from 3.8 to 9.8lpm being less than the typical building loop flow of 9.5 to 11.4lpm.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.141-150
• /
• 1992

Rapid change of urban area become a serious cause of disaster in existing drainage systems, and the practical alternatives in that situations are needed. The purpose of this study is to evaluate safety, one of drainage systems, detention reservoir and pumping station by new pumping criteria. New drainage pumping criteria, divided into two parts (rising limb and falling limb), which used in reservoir routing, shows more efficient flood prevention effect than existing criteria (based on the reservoir water level). To obtain the optimal range of flood prevention, sensitivity analysis of each inflow v.s. pumping capacity is tested. As a results, using 10 year design rainfall, 60% of detention reservoir and drainage pumping stations in Seoul are safe. In this results, there must be a fundamental and powerful counterplans to prevent inland flooding in Seoul metropolitan area.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.3
• /
• pp.267-272
• /
• 2012

Carbon emission generated by energy issues is one of the major problems which all countries concern. The International Energy Agency recommends to improve 15-30[%] of energy efficiency than now. Government has pushed the domestic energy saving policies and incentives and penalties were also given in that direction. Pumps are widely used to transfer fluids and they consume at least 20[%] power of each nation. Their loss of energy is huge if they have been operated at low efficiency for long time. Low efficiency of these pumps is often due to incorrect design or degradation. Pump efficiency can be measured to estimate energy loss. If it is low, the pump may be repaired or replaced with new one. This paper introduces thermodynamic method to measure pump efficiency using only two kinds of sensors for temperature and pressure. It can calculate best efficiency point(BEP) of actual systems easily and fast. Its values were compared with the real performance curve provided by pump maker and we got almost similar performance curves from the repeated experiment.

• Journal of Biomedical Engineering Research
• /
• v.10 no.2
• /
• pp.139-150
• /
• 1989

A new motor-driven blood pump for artificial heart was developed. In this blood pump, a small size, high torque brushless DC motor was used as an energy converter and the motor rolls back and forth on a circular track. This movement of the "rolling-cyliner" causes blood ejection by alternately pushing left or right polyurethane blood sacs. This moving-actuator mechanism could be eliminate two potential problems of other motor-driven artificial hearts such as large size and poor anastomosis for the implantation. Theoretical analyses on the pump efficiency, the temperature rise, and the inflow mechanism were also performed. In a series of mock circulation tests, the theoretical analyses were compared to the measured hemodynamic and mechanical values. The pump system was shown to have sufficient cardiac output (upto 9 L/min), sensitivity to preload, and mechanical stability to be tested as an implantable total artificial heart.ial heart.

• JOURNAL OF ELECTRICAL WORLD
• /
• s.412
• /
• pp.66-67
• /
• 2011

우리나라는 원자력발전 3대 핵심기술인 원전계측제어시스템(MMIS), 원자로냉각재펌프(RCP), 원전설계핵심코드의 국산화를 추진하고 있다. 지난해 가장 먼저 MMIS가 국산화에 성공했으며, IAEA로부터 우수성을 평가받을 정도로 기술적 우위를 확보했다. 원전설계핵심코드 중 노심설계코드도 2010년에 개발을 완료하였다. RCP도 일부 구성품은 이미 국산화에 성공하였으며, 2012년에 순수 국산제품 개발이 완료될 예정이다.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.1
• /
• pp.18-23
• /
• 2011

The hydraulic part in reactor coolant pump consists of suction nozzle, impeller, diffuser, and discharge nozzle. Among them, impeller is required to be designed to satisfy performance requirements such as head, NPSHR, and head curve slope at design point. Present study is intended to suggest the preliminary design method sizing the impeller size to satisfy the design requirement particularly including head curve slope at design point. On a basis of preliminary design result, hydraulic components have been designed in detail by CFD and then manufactured in a reduced scale. Experiment in parallel with computational analysis has been executed in order to confirm the hydraulic performance. Comparison results show good agreement with design result, confirming the validity of design method suggested in this study.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.787-790
• /
• 2011

본 연구에서는 페수열 회수 보일러에서 버려지는 페수열을 재생하여 에너지를 재활용하기 위하여 퍼지제어 알고리즘을 사용한 지능제어기를 설계하고자 한다. 폐수유입온도의 변화와 폐수유입량의 변화를 파라미터로 하여 컴프레서의 정속운전 대수와 토출온수온도의 특성곡선을 전문가의 지식으로부터 얻을 수 있다. 폐수열 회수 보일러에 유입되는 폐수부하에 따른 컴프레서의 정속운전 대수를 최소화 하기위해 폐수유입온도와 유입량의 변화를 측정하여 최적의 정속운전 대수 및 인버터 운전량을 실시간으로 결정하는 지능제어기를 설계하여 페수열 부하의 변동을 실시간으로 추정하여 최소의 컴프레서 운전대수 및 조작량을 제어함으로써 에너지 효율과 경제성을 극대화할 수 있다.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.127-128
• /
• 2010

As P-new-city is planned and constructed, district eating utilizing an existing near-by power plant's waste heat is considered as an economic and environment friendly way of providing heating to the new city. Many pipeline diameters and pumping station location and capacity were assumed, investigated and optimized, to satisfy the customers' heat demand considering common district heating pipe-network design and construction practice, and also and construction, pumping station land price and construction and the pumping energy cost during lifetime of DH systems.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.491-496
• /
• 2005

A pump design system was constructed by several integrating in-house programs and commercial softwares to design and evaluate centrifugal pumps. An agent-based prototype framework has been developed for collaborative design and optimization of a centrifugal pump. This paper introduces the feasible technology needed to construct a pump design system based on software agents. The integrated design system, developed in the present study, was used in designing a centrifugal pump and modifying its impeller shape by using optimization processes to increase the pump performance.

• Journal of the Korean Vacuum Society
• /
• v.2 no.1
• /
• pp.17-22
• /
• 1993

본 논문은 포항가속기연구소에서 건설중인 PLS 2 GeV 선형가속기 진공계통의 설계에 관한 것이다. PLS 2GeV 선형가속기의 진공계통은 길이 3.07m인 42개의 가속관과 길이 약 400m의 도파관으로 구성되어 있다. 진공장치의 배치는 충분한 지역적 배기능력을 고려한 분산 배기방식으로 다지관 방식의 기계적 복잡성을 단순화하였다. 진공계는 가속관 중심과 도파관에서 5$\times$10-7Torr, 클라이스트론 출력장치에서 5$\times$10-8Torr까지 배기되도록 설계하였다. 주 진공펌프로는 가속관과 도파관 및 에너지 배가장치에 대하여 각각 용량이 60l/s와 120l/s인 sputter 이온펌프를 사용하기로 하였다.