• 대한소아치과학회지
• /
• 제23권3호
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• 한국토양비료학회지
• /
• 제42권5호
• /
• pp.399-407
• /
• 2009

레이저 유도붕괴 분광법(LIBS)은 물질상태(고체, 액체, 기체)에 상관없이 신체 접촉시 오염 우려 및 미량 시료도 전처리 없이 동시에 많은 종류의 원소 분석으로 분석과정이 단순하고 신속하게 분석이 가능하며, 소형화된 레이저의 개발로 시료의 직접적인 채취가 어려운 조건의 현장분석에도 적합하다. 농산물 안정성 평가나 친환경 농업 및 정밀농업을 위한 조사 등에 활용될 수 있는 비파괴 실시간 정량분석기술로서 LIBS 분석법의 토양분석 가능성을 평가하고자 표준광물, 미국의 표준기술연구소의 표준토양, 미국 테네시주 초지 및 밭토양을 대상으로 토양 구성성분의 정성 정량적 분석에 필요한 측정조건을 조사하고 이를 토대로 LIBS에 의한 농도값과 기존의 화학분석법을 통해 측정한 결과를 비교하였다. LIBS 측정은 펄스형 Nd:YAG 레이저(Minilite II, Continuum, Santa Clara, CA)에서 나오는 1064 nm 에너지 파장의 광원을 시편의 플라즈마를 생성시키는데 사용하였고, 25 mJ/pulse 여기 에너지 빔을 펄스폭 35 ns, 펄스 반복 주기 10 Hz, 노출시간 10 s 동안 시료의 표면에 조사하였다. LIBS 분광은 0.03 nm의 해상력으로 200 nm에서 600 nm의 영역에서 50 m 이하로 분쇄하여 원형 펠렛 형태로 압축시킨 시료를 10 rpm의 속도로 회전시키면서 상온 상압의 실험실 조건에서 수행되었다. LIBS를 이용한 토양 중 주요한 원소의 적정 파장(nm)은 Al(I) 309.2 nm, Ca(I) 422.6 nm, Fe(I) 406.4 nm, Mg(I) 285.2 nm, Na(I) 589.2 nm, Si(I) 288.2 nm, Ti(I) 398.9 nm 이었다. LIBS의 피크강도가 물질 중 원소의 농도가 증가됨에 따라 각 원소의 특정 파장대에서 일정하게 증가되는 것으로 나타나고 있으나 표준물질의 LIBS의 신호비와 원소비를 통해 측정된 검량곡선의 상관계수($r^2$)는 0.863에서 0.977의 범위로 원소별로 상이할 뿐만 아니라 0.98에 미치지 못하였다. 또한, 토양 중 분석대상원소에 대하여 기존 ICP-AES에 의한 표준방법으로 분석된 시료의 측정값과 비교하여 상대적인 오차는 대략적으로 (-)40%에서 80%이상이며, 평균오차는 32.2%로 표준척도 20% 이상을 초과하였다. LIBS에 의한 토양분석은 토양의 조성과 입자의 크기에 따른 매질효과(matrix effect)로 표준물질의 검량곡선에서 결정계수가 낮고, 원소별 함량도 기준의 표준방법과 비교할 때 오차가 컸다. 따라서 LIBS에 의한 토양분석은 정성적인 분석 수준의 정밀도를 보였으며, 토양 매질의 영향을 최소화하기 위하여 기존의 분쇄 펠렛형 시료조제 및 회전측정 이외의 다양한 토양매질의 표준물질(standard reference material)의 확보, 새로운 전처리 방법 및 측정상 방법개선 등 신뢰성 있는 정량 분석을 위한 노력이 필요할 것으로 사료된다.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권4호
• /
• pp.289-293
• /
• 1994

Thin films of YB $a_{2}$C $u_{3}$$O_{7-x}$ supercondYB $a_{2}$C $u_{3}$$O_{7-x}$uctor were prepared on (100) SrTi $O_{3}$ substrates by pulsed laser deposition using visible light laser. Q-switched Nd:YAG(532 nm, 30 ns) pulsed laser was used for deposition. The effects of substrate temperature and oxygen pressure during deposition on films were studied. Critical current density of 2.93*10$^{6}$ A/c $m^{2}$ at 77K and Tc(zero)=91.7K were obtained from the film prepared with Tsub=745.deg. C and $P_{02}$=200 mTorr. XRD analysis showed that the grown film has c-axis normal orientation to the substrate surface and has single phase. Surface morphology of the film has been improved by interfering the plume ejected from YB $a_{2}$C $u_{3}$$O_{7-x}$ target.arget.t.

• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.316-321
• /
• 2009

Co nanoparticles on silica substrates were fabricated by inducing a thin-film dewetting through two different processes-furnace annealing and pulsed-laser annealing. The effects of annealing temperature, film thickness and laser energy density on dewetting morphology and mechanism were investigated. Co thinfilms with thicknesses between 3 to 15 nm were deposited using ion-beam sputtering, and then, in order to induce dewetting, thermally annealed in furnace at temperatures between 600 and $900^{\circ}C$. Some as-deposited films were irradiated using a Nd-YAG pulsed-laser of 266 nm wavelength to induce dewetting in liquid-state. Films annealed in furnace agglomerated to form nanoparticles above $700^{\circ}C$, and those average particle size and spacing were increased with an increase of film thickness. On the laser annealing process, above the energy density of $100mJ/cm^2$, metal films were completely dewetted and the agglomerated particles exhibited greater size uniformity than those on the furnace annealing process. A detailed dewetting mechanism underlaying both processes were discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.170-173
• /
• 2001

Thin films of phase-pure perovskite (P $b_{0.72}$L $a_{0.28}$) $Ti_{0.93}$ $O_3$(PLT) were deposited in-situ onto Pt/Ti/ $SiO_2$/Si substrates by pulsed laser deposition. We have systematically investigated the variation of grain sizes depending on the process condition. Both in-situ annealing and ex-situ annealing treatments have been compared depending on the annealing time. Two-step process to grow (P $b_{0.72}$L $a_{0.28}$) $Ti_{0.93}$ $O_3$(PLT) films was adopted and verified to be useful to enlarge the grain size of the film and to enhance the leakage current characteristics. The grain sizes of PLT thin films were successfully controlled 260 to 350 nm by changing process parameters. Electrical properties including dielectric constant, ferroelectric characteristics, crystallization and leakage current of PLT thin films were shown to be strongly inf1uenced by grain size. Also PLT thin films on p-type(100) Si substrate will be fabricated by pulsed laser deposition technique using a Nd:YAG laser with different wavelengths of 355, 532 and 1064 nm. Effect of the variation of laser wavelength on dielectric properties will be discussed. Microstructural and electrical properties of the film were investigated by C-V measurement leakage current measurement and SEM.ent and SEM.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.79-79
• /
• 2008

We report the growth of $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thin films and their substrate-dependent electrical characteristics. BST thin films were deposited on alumina(non-single crystal), $Al_2O_3$(100) substrates by Nd:YAG Pulsed Laser Deposition(PLD) with a 355nm wavelength at substrate temperature of $700^{\circ}C$ and post-deposition annealing at $750^{\circ}C$ in flowing $O_2$ atmosphere for 1hours. BST materials had been chosen due to high dielectric permittivity and tunability for high frequency applications, To analyze the oxygen partial pressure effects, deposited films at 1, 10, 50, 100, 150, 200, 300 mTorr. The effects of oxygen pressure on structural properties of the deposited films have been investigated by X-ray diffraction(XRD) and atomic force microscope(AFM), respectively. Then we manufactured a inter-digital capacitor(IDC) patterns twenty fingers and $10{\mu}m$ gap, $700{\mu}m$ length and electrical properties were characterized. The results provide a basis for understanding the growth mechanisms and basic structural and electrical properties of BST thin films as required for tunable microwave devices applications such as varactors and tunable filters.