• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.250-254
• /
• 2001

본 문에서는 Tschebyscheff 다항식 이론을 이용하여 상대적 전류 분포비가 1:2:2:1이 되도록 마이크로스트립 패치 어레이 안테나(MPAA) 설계 제작하였다. 지향성을 갖는 제안된 안테나는 작고 가벼우며 얇다. 또한 빔폭이 14。 인 어레이 안테나이고, 중심 주파수는 10.2553GHz이다. MPAA는 한 개의 마이크로스트립 패치 안테나(SMA:single microstrip antenna)특성과 비교 분석하였다. 그 결과 MPAA는 SMA보다 보다 좁은 복사 전력 빔폭과 큰 최대 복사 전력 이득을 획득했다. PIN 다이오드를 이용한 위상 변환기를 적용하면 전자적 빔스케닝이 가능하고, 소형 레이더 시스템에 적합하다.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.156-161
• /
• 2006

In this paper, an E-patch antenna on the U-shaped ground plane is designed and experimental studied. In order to reduce to cross-polarization level and to enhance the gain of the microstrip patch antenna, a U-shaped ground plane is employed in the microstrip patch antenna. As a main radiator, an E-shaped patch is used to reduce the antenna size as small as possible. Also to enhance the bandwidth of the antenna, a substrate of the lowest permittivity of which thickness as thick as possible is used and a rectangular patch is overlaid on the air substrate of the E-shaped patch antenna. The radiation characteristics of the antenna are calculated by CST Microwave Studio 5.0 simulation software. Experimental results show that by increasing the height of the sidewall of the ground plane, the antenna gain is increased and the cross-polarization level is decreased.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.467-474
• /
• 2019

In this paper, we studied a method for a broadband stacked patch antenna structure which is widely used for bandwidth improvement. The characteristics according to the distance between the two patches were analyzed and the impedance matching was optimized by connecting parallel open stubs to the main patch feed line. The shunt matching stub is inserted underneath the parasitic patch and so it does not require additional space, which enables the proposed antenna structure to be advantageous in miniaturizing antenna. The effects of the various parameters on the antenna performance are examined, and we introduced the design procedure for the proposed antenna to operate in the frequency range of 2.3~2.7GHz. Experimental results show that the bandwidth of the proposed antenna is about 480MHz with 2.27~2.75GHz bandwidth. And the antenna gain was 5.8dBi at 2.3GHz and 7.8dBi at 2.6GHz within the bandwidth.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.180-183
• /
• 2006

In this study, an supplementary microstrip patch with a comb-pattern slot is positioned on the conventional single layer microstrip patch antenna. Numerical results of the antenna bandwidth and the antenna gain are increased compared with those of the conventional single layer microstrip patch antenna. In the future, the geometry of the slot in an supplementary microstrip patch is researched for the enhancement of the microstrip antenna characteristics.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.10
• /
• pp.37-42
• /
• 2000

There has been a constant effort to study methods for increasing the bandwidth of antenna by microstrip patch. In this paper, we propose a special type of the external rectangular patch, for design and analysis of an antenna using a local multi-point distribution system (LMDS). We minimized electromagnetic emissions from the fringing effect. As a result, we obtained an increase in antenna efficiency and frequency bandwidth. We were also able to design the wide band antenna easily, because of the difference in parameter between the aimed and the simulated antenna was reduced greatly. In comparison with the rectangular patch antenna, the banded one has a wider bandwidth.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.1
• /
• pp.245-252
• /
• 2018

In this paper, the dual band circular polarization patch antenna was designed by using band rejection characteristics of CSRR structure for geostationary satellites. A quadrangular CSRR structure was etched on the ground at the rear of the patch antenna's feed to obtain band rejection characteristics in between the receiving frequency band(1525~1559MHz) and transmission band(1626.5~1660.5MHz), and the corner of the patch antenna was truncated to enable circular polarization. It was confirmed that the resonant frequency of the patch antenna differs according to the size anc location of the CSRR and cirular polarization characteristics with simulation and measurement results. Measurement results shows the gain of about 0.2dB and 1.5dB in the TX and RX band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.215-221
• /
• 2009

In this paper, a slotted trapezoidal microstrip fractal patch antenna is designed and fabricated for the vehicle GPS antenna. We designed air substrate patch antenna to obtain gain improvement by the elimination of dielectric loss. By applying fractal structure with crossed slot to trapezoidal patch, we obtained 42.5 % as much patch size as conventional triangular patch antenna. Measured bandwidth was 200 MHz on GPS band under VSWR 2:1 And gain was 4.31 dBi at resonant frequency that is 2$\sim$5 dB higher gain than conventional ceramic patch antenna on GPS band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2066-2072
• /
• 2014

In this paper, We proposed a UWB microstrip patch antenna with an O-shaped slot of the step structure and analyzed the characteristics of the antenna. In order to improve of frequency properties, size of the patch radiating element, radius change of the O-shaped slot, width of the feed line and a rectangular slot were optimized by CST simulation program. The proposed antenna showed that the 2.8GHz ~ 11.4GHz frequency, the minimum return loss and -10dB bandwidth were -32.39dB and 8.6GHz, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.259-264
• /
• 2016

In this study, the properties of a patch antenna fed by a coplanar waveguide with ground (CPWG) and design method were studied. The antenna was impedance-matched to the CPWG feedline by adjusting the width, length, and position of the patch. To improve the frequency properties of the CPWG type antenna, patch length, patch width, patch position, and ground distance were simulated using HFSS (High Frequency Structure Simulator) simulation program. A CPWG antenna of 1.8 GHz for LTE band was designed and fabricated by photolithography on an FR4 substrate (dielectric constant of 4.4 and thickness of 0.8 mm). The fabricated antenna was analyzed using a network analyzer. The measured results agree well with the simulations, which confirmed the validity of this study. The fabricated CPWG antenna showed a center frequency, minimum return loss and -10dB bandwidth of 1.8GHz, -32.1dB, 22MHz and $50.2{\Omega}$ respectively. The proposed antenna is expected to be applicable to the LTE band.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.72-73
• /
• 2016

In this paper, we studied a method for miniaturizing a broadband stacked patch antenna structure which is widely used for bandwidth improvement. Main patch is a rectangular microstrip patch antenna fed by a 50-ohm microstrip line, and a parasitic patch is laid above the main patch. The size of the main patch is designed to be resonated near the center frequency of the desired frequency band. Then parasitic patch longer than main patch is placed above the main patch. The distance between two patches might be adjusted so as to achieve impedance matching using a shunt open stub. The shunt matching stub is inserted underneath the parasitic patch and so it does not require additional space, which enables the proposed antenna structure to be advantageous in miniaturizing antenna. The effects of the various parameters on the antenna performance are examined, and we introduced the design procedure for the proposed antenna to operate in the frequency range of 2.3-2.7 GHz.