• Journal of Korean Society of Steel Construction
• /
• v.12 no.5 s.48
• /
• pp.487-494
• /
• 2000

This paper intends to propose design information with the result or comparing the deformation capacity with different panel stiffness specimens and estimating the plastic deformation capacity, toughness and strength of welded joint connection according to the different scallop types. The test results of the beam to column unit structure are as follow: the non-scalloped and the low stiffness panel specimen have more desirable result values than the scalloped and the high stiffness one in plastic deformation. Comparing the scallop types shows very unlikely tendency as follows, second cracking occurs at the very edge of scallop in the scalloped specimen otherwise cracking occurs bond area of welded beam flange in the non-scalloped one.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.9-20
• /
• 2019

The number of natural disasters in Korea, such as earthquakes, is increasing. As a result, there is growing need for temporary residences or shelters for disaster conditions. The aim of this study was to produce post-disaster refugees housing differentiated from existing shelters using lightweight composite panels. To accomplish this, the structural performance of lightweight composite panels was validated, and an in-plane shear strength test was conducted according to the ASTM E72 criteria among the performance test methods for panels. As a result of the experiment, the maximum load for each specimen under an in-plane shear load was determined. All the experiments ended with the tear of the panel's skin section. The initial stiffness of the specimens was consistent with that predicted by the calculations. On the other hand, local crushing and tearing, as well as the characteristics of the panel, resulted in a decrease in stiffness and final failure. Specimens with an opening showed a difference in stiffness and strength from the basic experiment. The maximum load and the effective area were found to be proportional. Through this process, the allowable shear stress of the specimens was calculated and the average allowable shear stress was determined. The average ultimate shear stress of the lightweight composite panels was found to be $0.047N/mm^2$, which provides a criterion of judgement that could be used to expect the allowable load of lightweight composite panels.

• Journal of the Korea Concrete Institute
• /
• v.14 no.4
• /
• pp.483-491
• /
• 2002

This paper summarizes the results of experimental studies concerning the flexural strengthening of reinforced concrete beams by the external bonding of the new reinforcement material, which is composite panel with an advanced fiber sheet bonded on light concrete precast panel. The structural behaviors of strengthened beams are compared with codes in terms of yield load and ultimate load, deflection, flexural stiffness, ductility. Thirty nine large-scale beams were tested experimentally to evaluate the strength enhancement provided by the composite panel. According to the results, it is shown that beams strengthened with composite panel are structurally efficient and that the strength of the strengthened beams are improved comparing with beams strengthened with fiber sheet.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.5
• /
• pp.519-530
• /
• 2013

Cyclic tests on modular building units for low-rise buildings composed of stud panels and a light-weight steel perimeter frame, were performed to evaluate the earthquake resistance such as stiffness, load-carrying capacity, ductility, and energy dissipation per load cycle. The strap-braced and sheeted stud panels were used as the primary lateral load-resistant element of the modular building units. Test results showed that the modular building units using the strap-braced and sheeted stud panels exhibited excellent post-yield ductile behaviors. The maximum drift ratios were greater than 5.37% and the displacement ductility ratios were greater than 5.76. However, the energy dissipation per load cycle was poor due to severe pinching during cyclic loading. Nominal strength, stiffness, and yield displacement of the modular building units were predicted based on plastic mechanisms. The predictions reasonably and conservatively correlated with the test results. However, the elastic stiffness of the strap-braced stud panel was significantly overestimated. For conservative design, the elastic stiffness of the strap-braced stud panel needs be decreased to 50% of the nominal value.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.3
• /
• pp.167-174
• /
• 2008

The objective of this study is to verify whether the composite action is sufficiently strong to withstand at the interface and the structural behavior of LB-DECK panel with field concrete slab strengthened with main reinforcing bars. Static and fatigue tests are performed for LB-DECK panels with varied shapes and amounts of rebars, and the results are compared with those of field concrete panel(FCP). The test results indicate that the LB-DECK panel with 1.5 times of more rebars inside significantly increase the overall stiffness. LB-DECK penel usually shows on average 52.1 percent of improved stiffness compared with the FCP. The fatigue test results also show that the LB-DECK panel can withstand two-million cycles of repeated loads without any damage.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.3
• /
• pp.105-115
• /
• 2007

Repair and Reinforcement are subjected change to increasing of remodelling. The usage of carbon fiber sheets is increasing for the strengthening of reinforce concrete structures. Therefore experimental and analytical studies are carry out to investigate the flexural behaviors of the strengthened RC structures by the external bonding of the new reinforcement method. Also the aim of this study is to investigate reinforcing method of FRP panel deal with fatigue loading through experiments.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.4
• /
• pp.373-380
• /
• 2001

The problem addressed in this study is how to analytically treat the partial composite action for wall panels. An equation, derived for wood-joist floor systems, which determines deflections for beams with partial composite action is introduced. The equation is applied to the calculation of the mid-span deflection for gypsum-sheathed, cold-formed steel was stud panels. The objective of this study is to properly reflect the influence of the following factors in the calculation of mid-span deflection for the panel: connection slip, local buckling, perforations in the stud web, and effects from joints in the sheathing. Predicted deflections based on an upper bound for connection rigidity were closest to experimental deflections.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.4
• /
• pp.447-456
• /
• 2006

In this study, a torsional test for U-type steel box girders was performed to observe the effects of the kind of panel for top lateral walateral bracings on the torsional behavior of the U-type steel girder system. For the structural tests, the test specimen with a two-thirds scale of the system actually constructed in the field was used. In the torsional test to observe the efects of top lateral bracings, the most economical arrangement of the top lateral bracing was found to be the panel width to length ratio of 1:1.5 with the inclined angle of $40^{\circ}$.

• Information Display
• /
• v.7 no.2
• /
• pp.14-22
• /
• 2006

• Journal of Korean Society of Steel Construction
• /
• v.8 no.4 s.29
• /
• pp.105-113
• /
• 1996

본 연구에서는 철골모멘트골조의 패널존변형을 명시적으로 고려한 탄성층 간변위의 근사해석 방법을 제안하였다. 본 방법은 고전적 포탈법의 가정 및 D 치법에 기반한 해석적 접근법이다. 즉 포탈법의 가정에 따라 횡력을 받는 골조를 보-기둥 부분 골조로 분해한 후 대표적 내부 부분골조의 보, 기둥 및 패널존에서 기인하는 모든 횡변위 성분을 해석적으로 계산한다. 이때에 필요한 모든 내력(가령 패널존 전단변형 산정을 위한 보의 불균형모멘트)의 결정에 D 치법을 이용한다. 구조바닥의 강막작용을 고려하면 위의 과정을 통하여 산출된 대표적 내부 부분골조의 횡변위는 전체 골조의 횡변위와 거의 동일할 것으로 기대할 수 있다. 본 방법의 타당성 여부는 반강절 접합요소를 사용한 해석적 엄밀해와 비교하여 검증하였으며 만족스런 결과를 주는 것을 확인하였다. 본 연구의 방법에 의해 컴퓨터해석에 의하지 않고도 철골모멘트골조의 탄성층간변위를 실용성있는 정확도로서 신속하게 산정할 수 있으므로 본 연구의 결과는 예비적 횡강성 평가에 유용하게 사용될 수 있다. 또한 본 방법의 적용과정에서 해석자는 철골모멘트골조의 횡변위 기동에 관한 물리적 감각을 증진시킬 수 있을 것으로 사료된다.