• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.05b
• /
• pp.1117-1120
• /
• 2003

DWDM(DensedWavelengthDivisionMultiplexing)은 광 파이버를 이용하여 기존의 통신보다 높은 대역폭(B/W)을 얻기 위한 기술로 여러 신호를 각각 다른 파장으로 변조해 하나의 Fiber 를 통해 전송하는 방식이며, 기본적으로 EDFA(Erbium Doped Fiber Amplifier), AWG(Arrayed Wave guide Grating), OADM(Optical Add/Drop Multiplexer) 등의 주요 부품과 여러 광 관련 부품들로 구성돼 있으며, 다수의 파장을 MUX(AWG)에서 다중화하고, 장거리 전송을 위해 OA(EDFA)에서 광신호를 증폭하게 된다 그리고 일부 특정 파장만 Add/Drop하기 위해 OADM이 놓이게 되며, 또한 선로(광섬유)의 손실을 보상하기 위해 필요한 구간에 리피터(EDFA)를 두어 광신호를 증폭 송신하며 수신단에서는 들어오는 여러 파장을 OA(EDFA)를 통해 증폭한 후 DEMUX(AWG)에서 역 다중화해 수신하게 된다. 이와 같은 DWDM방식을 이용한 Network는 Star, Mesh, Ring 등의 다양한 형태로 구성될 수 있으며, 초기에는 Point-to-Point 방식의 장거리 전송에 주로 사용돼 왔으나 Metro 구간의 Traffic 이 급격히 증가하면서 Metro- DWDM Network 이 부각되고 있어 본 논문에서는 현재 SK Telecom에서 상용화되고 있는 1,600G DWDM과 Metro-DWDM간의 망 구축의 최적화 방안을 연구해 본다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2280-2288
• /
• 2014

The conventional dimming control methods of LED (Light-emitting dioades) include Analog, PWM (Pulse Width Modulation), and FM (Frequency Modulation) Control. Analog dimming is controlled by adjusting forward current of Power LED. Although Analog dimming is possible to control linearly the brightness levels on a whole range (0%~100%), it comes into existence a variation of wavelength by changing the Power LED's forward current. PWM dimming has achieved by varying in duty of full current flowing to the Power LED. Generally, PWM dimming doesn't make variation of wavelength but have difficulty with adjusting the linear brightness level between 0% and 10%. FM dimming method is on the same wavelength as PWM dimming, however, it has problem of flickering at low level of dimming. This paper propose a efficient dimming control method of Power LED in order to overcome the disadvantages of the above mentioned methods. We apply to Analog method in low level of dimming control and use PWM method in dimming range from 10% to 100%. For the experiment, we design and implement a circuit and test the proposed method. Consequently, we can control the linear brightness of Power LED across the whole range and get the constant wave at different dimming level. The experimental results show the benefits of the proposed method.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.150-151
• /
• 2002

파장 분할 다중화(Wavelength division multiplexing ： WDM) 광전송 장치의 용량확대를 위한 방안으로 여러 가지 방법들이 연구 개발되고 있으며, 최근 들어 테라 급(Tb/s) 광전송 연구 결과들이 발표되고 있다. 이러한 장거리 광전송 장치의 광송신기는 LiNbO$_3$ 마하-젠더(Mach-Zehnder) 간섭계형 외부 변조기를 주로 사용하고 있다. 한편 반도체 레이저 집적된 전계 흡수형 변조기(Electro-absorption modulator integrated laser ： EML)를 이용한 외부 변조 방식 적용을 위해서 여러 연구소 및 기업체에서는 40Gb/s의 성능을 지닌 EML의 개발 결과들을 발표하고 있다. (중략)

• Korean Journal of Optics and Photonics
• /
• v.7 no.3
• /
• pp.287-294
• /
• 1996

An optical phase modulator is fabricated in GaAs/AlGaAs doble heterostructure wafer grown by MOCVD. A self-aligned process, in which the same photoresist pattern is used for both the waveguide etching and the insulation layer formation, is developed and is found to be very useful, Fabry-Perot interference technique is applied to the measurement and the phase modulation efficiency is measured to be 22.5$^{\circ}$/Vmm at 1.31 ${\mu}{\textrm}{m}$ for TE polarization.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.02a
• /
• pp.425-426
• /
• 2008

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.418-422
• /
• 1994

본 연구에서는 MOVPE를 이용한 MQW활성층을 DFB-LD 구조에 도입함으로서 2.5Gbps 광전송용 광원으로 사용된 $ 1.55.\mu$m 파장의 MQW-PBH-DFB-LD를 제작하였다. 활성층으로는 MOVPE를 이용하여 8쌍의 InGaAs/InGaAsP MQW층을 성장하였으며 2차 및 3차 결정성장은 LPE를 사용하였고 발진파장을 결정하는 회절격자 주기는 238nm로 하였다. MQW-PBH-DFB-LD의 평균 임계전류는 13.81mA, Slope efficiency는 0.137mW/mA이었고 발진파장은 1548.6nm의 특성을 얻었다. 그리고 2.5Gbps 대신호 변조시의 chirping특성을 조사하여 본 결과 0.55nm임을 확인할 수가 있었다.

• Korean Journal of Optics and Photonics
• /
• v.10 no.5
• /
• pp.430-438
• /
• 1999

We have utilized soft-aperturing by gain media to develop a high-power tunable Ti:Sapphire laser with sub-40-fs and broad tuning range. The tunable spectral range was only limited by the bandwidth of mirrors. We made use of knife-edge slits near an intra-cavity prism controlled by micro-stepping-motors to tune the center wavelength continuously. The tunability of the center wavelength was ranged from 770 nm to 870 nm, and the measured pulsewidth was sub-40 fs throughout the above spectral range. The shortest pulsewidth was about 17 fs at the center wavelength of 820 nm and the spectral bandwidth was 72 nm. At 5 W pumping power of the Ar-ion laser we obtained average output power of 440 mW~580 mW. For the cw and Kerr-lens mode-lodking conditions, we have evaluated the value of an amplitude modulation to be ${\gamma}=2.5{\times}10^{-8}/W$ from the calculated waists of a Gaussian beam on the Ti:sapphire crystal surface. Using this result we demonstrate that the generation of sub-40-fs Kerr-lens mode-locked pulse can be described by the Ginzberg-Landau model which is a weak pulse shaping model.

• Journal of the Korean Society of Radiology
• /
• v.6 no.3
• /
• pp.207-215
• /
• 2012

As one of photo dynamic therapies, the existing LED photo irradiation method with 635 nm continuous wave has most frequently been used for acne treatment, it suffered from a low energy efficiency and generation of a large amount of heat in tissues requiring improvement measures. In this thesis, a LED photo irradiation system for acne treatment has been designed using PWM(Pulse Width Modulation) mode to enhance the energy efficiency and prevent thermal destruction in tissues. System configuration consisting largely of timer module, PWM module, and photo transfer device has been designed with the use of 1 W LED at a wavelength of 660 nm for the photo transfer device to increase skin penetration depth for treatment of acne. Frequency and wave form generated by using PWM control was verified along with confirmation of output energy of 660 nm LED and surface temperatures of tissues, followed by evaluation of stable energy outputs and stability of tissues. The results indicated that whereas power loss was high and thermal destruction in tissues was exhibited when C.W mode was used to obtain the optical energy of 1 W LED at a wavelength of 660 nm for acne treatment, realization of PWM mode allowed lowering of power consumption for LED through pulse width modulation, and no occurrence of thermal destruction in tissues, suggesting that PWM mode is safer and more effective for treatment of acne than C.W mode.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.1-6
• /
• 2006

By comparing video-overlay method where digital and SCM signal are modulated in different optical source, we experimentally investigated the performance of simultaneous modulation of data and broadcasting signals using a single LD for broadcasting in PON based optical access network. The experimental results show that by increasing the minimum value of injected current for LD modulation above about 1.5 times of threshold current of LD, data and broadcasting signals can modulate without mutual interference. We also proposed and demonstrated the scheme of optical transmitter optimized for simultaneous modulation of data and broadcasting signals where anode and cathode of LD are separately used as signal interface for data and broadcasting signals, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2285-2290
• /
• 2011

This paper is the research on SMSR yield improvement of the optical transceiver using modulated DFB laser. In general, the wavelength of DFB laser optical transceiver are 1310, 1490 and 1550 nm. Usually SMSR in modulated DFB is difficult to improve as low as 30 dB because of high slop efficiency trade off. In modulation condition, we studied SMSR improvement according to adjust bias current, extinction ratio and optical line terminal receiver sensitivity. As our test results, we can found a method how to improve SMSR for optical transceiver for long distance.