• The Journal of Engineering Geology
• /
• v.6 no.2
• /
• pp.95-102
• /
• 1996

A study on the attenuation of ground vibration was carried out on the soil layer using seismic exploration method. A 12-channel engineering seismograph was used to acquire real digital amplitude data in field work. Frequency analysis of seismic data shows maximum spectrum amplitude around 40Hz. Relative amplitude decreases exponentially as the distance increases and the attenuation factors are n = 0.25 and a = 0.13-0.20. Internal attenuation indexes(a) are 0.13 and 0.20 in the wet soil zone and the vegatated soil zone, respectively. It means that ground vibration attenuates faster in vegatated soil zone than in wet soil zone. Average internal attenuation coefficient(h) was determined to be 0.094 from seismic velocity and frequency analysis.

• Journal of the Korean earth science society
• /
• v.38 no.2
• /
• pp.161-171
• /
• 2017

Observed ground motions are composed of three factors such as, seismic source, attenuation, and site amplification effect. Among them, the site amplification characteristics should be considered significantly when estimating seismic source and attenuation characteristics with more confidence. The site effect is also necessary when estimating not only seismic hazard in seismic design engineering but also rock mechanical properties. This study uses the method of H/V spectral ratio of observed ground motion between target site and reference site called a reference site method. In addition to using the vertical Fourier spectrum of the reference site, we try out the horizontal Fourier spectrum as a new method in this study. We analyze H/V spectral ratio of six ground motions respectively, observed at four sites close to Yedang Reservoir. We then compare site amplification effects at each site using 3 kinds of seismic energies including S waves, Coda waves energy, and background noise. The results suggest that each site showed similar site amplification patterns in S waves and Coda waves energy. However, the site amplification of background noise shows much different characteristics from those of S waves and Coda wave energy, which suggests that the background noises at each site have their own developing mechanism. Each station shows its own characteristics of specific resonance frequency and site amplification properties in low, high and specific resonance frequency ranges. Comparison of the method used in this study to the others that used different methods can provide us with more information about the dynamic amplification of a site characteristics and site classification.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.1E
• /
• pp.37-44
• /
• 1994

A method for measuring the loudspeaker distortions at low frequencies without an anechoic is proposed. This method is based on the fact that the n-th harmonic distortion outside the enclosure is boosted by 40log n dB compared to that inside the enclosure. The applicable frequency range is extended by cancelling the effect of standing wave inside the enclosure. Causes of measurement error are also analyzed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.504-509
• /
• 2005

This paper evaluates the BER performance of MC-DS-CDMA systems in frequency selective Rayleigh fading channel, considering the carrier frequency offset and the nonlinear high power amplifier. In the uplink MC-DS-CDMA, the BER performance is better than in the downlink. This paper presents the required output back-off of the nonlinear amplifier and value of frequency offset for good BER performance.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.3
• /
• pp.23-32
• /
• 2004

The local geologic and dynamic site characteristics, which include soil profiles, shear wave velocity profiles and depths to the bed rock were gathered from 148 sites all over the Korean peninsula and those values are compared to those in the western USA. Site response analyses were performed based on equivalent linear scheme using design rock-outcrop acceleration of 0.154g which corresponds to the collapse level of earthquake for seismic category I structure. The results show that the amplification factor based on Korean seismic design guideline underestimates the motion in short-period range and overestimates the motion in mid-period range. It is suggested that the existing Korean seismic guideline based on UBC is required to be modified considering dynamic site characteristics in Korea for the reliable estimation of site amplification.

• Journal of the Korean earth science society
• /
• v.23 no.4
• /
• pp.357-368
• /
• 2002

In this study we have tried to explain the barrel-shaped morphology for young supernova remnants considering the dynamical effects of the ejecta. We consider the magnetic field amplification resulting from the Rayleigh-Taylor instability near the contact discontinuity. We can generate the synthetic radio image assuming the cosmic-ray pressure and calculate the azimuthal intensity ratio (A) to enable a quantitative comparison with observations. The postshock magnetic field are amplified by shearing, stretching, and compressing at the R-T finger boundary. The evolution of the instability strongly depends on the deceleration of the ejecta and the evolutionary stage of the remnant. the strength of the magnetic field increases in the initial phase and decreases after the reverse shock passes the constant density region of the ejecta. However, some memory of the earlier phases of amplification is retained in the interior even when the outer regions turn into a blast wave. The ratio of the averaged magnetic field strength at the equator to the one at the pole in the turbulent region can amount to 7.5 at the peak. The magnetic field amplification can make the large azimuthal intensity ratio (A=15). The magnitude of the amplification is sensitive to numerical resolution. This mens the magnetic field amplification can explain the barrel-shaped morphology of young supernova remnant without the dependence of the efficiency of the cosmic-ray acceleration on the magnetic field configuration. In order for this mechanism to be effective, the surrounding magnetic field must be well-ordered. The small number of barrel-shaped remnants may indicate that this condition rarely occurs.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.6
• /
• pp.665-670
• /
• 2015

In this paper, We proposed a broadband RF amplifier for Microwave band receiver. We also proposed a broadband RF amplifier, designed by using EM simulation for reliable amplification of the received signal. Connected to a source terminal to via, it minimizes those which are the active elements of source-side oscillation as the operating element in an ideal GND, and a constant gain characteristic in a broadband. The goal of this was to obtain stable amplification characteristics. For implementing this architecture, we designed the broadband(500 MHz ~ 7 GHz) RF amplifier by using commercial GaAs FET, which operate on 720 MHz, 4,595 MHz, and 6,035 MHz by impedance matching. The voltage gain is 10.635 dB ~ 14.407 dB(737.5 MHz ~ 6.0575 GHz), P1dB is 20 dBc of band(1st harmonic/2nd harmonic).

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.9
• /
• pp.29-36
• /
• 2014

Under the situation that the seismic vulnerability are a worsening problem in many world's megacities, the disaster preparedness including earthquake hazards is a matter of primary concern in the capital city of Korea, Seoul. Especially, because it is hard to move or dismantle the architectural heritages, the mitigation of earthquake damages is potentially more difficult than other structures. Moreover, in order to decide the proper preparedness plan against future earthquakes, it is very important to understand how soils pass the seismic waves to architectural heritages. In this paper, therefore, the ground condition and depth of bedrock was investigated by the MASW-method at heritages located in Seoul. Then one-dimensional seismic response analysis was conducted based on the distribution of shear wave velocity. As the major result of analyses, peak acceleration, site amplification factor and natural period are proposed in each site for recurrence period.

• Composites Research
• /
• v.35 no.1
• /
• pp.8-12
• /
• 2022

Analysis of defect signals inside glass fiber reinforced polymer (GFRP) was conducted through deconvolution of terahertz (THz) wave. The GFRP specimen with internal defects was manufactured and the THz signal was measured through the reflection mode of the Terahertz Time-Domain Spectroscopy (THz-TDS) system. For deconvolution of the measured THz signal, the peak position of the THz signal was amplified through Normalized Cross Correlation (NCC) of the incident and detected THz signals. The position and intensity of the amplified peak were extracted as impulse, and the extracted signal of the impulse position was removed from the THz original signal. By repeating the process, the critical impulses, which represent boundary of the specimen, were derived. The deconvolution process was verified by confirming that the original THz signal without noise can be restored through the convolution of the critical impulses and the incident signal. From the derived critical impulses, the thickness of the internal defect in the GFRP was calculated through the detection time of impulses within 15 ㎛ accuracy.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.5 no.1
• /
• pp.13-25
• /
• 1968

A detailed analysis of the transistor wide-band feedback amplifiers using the hybrid-$\pi$ equivalent circuit has been made. It is considered both for the low freqnency and for the high frequency. The expressions of the gain, bandwidth. input impedance and output impedance have been presented. It is shown that a series feedback amplifier should be driven from the voltage source and should drive into the low resistance load, and a shunt feedback amplifier should be driven from the current source and should drive into the high resistance load. It is also shown that these stages can be coupled without use of the buffer stage or coupling transformer.