• Composites Research
• /
• v.20 no.5
• /
• pp.34-42
• /
• 2007

Strength and failure of adhesively bonded carbon composite-to-aluminum single-lap joints were studied by experiment. The main objective of this study is to investigate the effect of various parameters such as curing pressure for bonding, overlap lengths, and adherend thickness on the failure loads and modes of the bonded Joints with dissimilar materials. Experimental results show that the bonding pressure for composite-to-aluminum dissimilar materials should be 4 atm at the lowest. Failure load of the joints increases as the overlap length increases, but the strength (failure load divided by bonded area) decreases rapidly after the overlap width-to-length ratio is greater than 1. When the adherend thickness increase to double, bonding strength increase $12{\sim}55%$. Major failure mode of the joints is the delamination in the composite laminate and the location of delamination goes deeper into the laminates as the bonding pressure and overlap length increase.

• Composites Research
• /
• v.13 no.2
• /
• pp.51-60
• /
• 2000

Filament wound pressure vessels have been studied for the efficient design tool to consider the variation of fiber angles through-the thickness direction. Filament winding patterns were simulated from semi-geodesic fiber path equation to calculate fiber path on arbitrary surface. Finite element analyses were performed considering fiber angle variation in longitudinal and thickness directions by ABAQUS. For the finite element modeling of the pressure tank, the 3-dimensional layered solid element was utilized. From the stress results of pressure tanks, maximum stress criterion in transverse direction was applied to modify material properties for failed region. In the end of each load increment, resultant layer stresses were compared with a failure criterion and properties were reduced to 1/10 for a failed layer. Results of progressive failure analysis were compared with two experimental data.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.183-186
• /
• 2008

Both structural analysis and hydraulic test have been conducted to confirm the burst characteristics of filament wound solid motor case. Failure criteria have been defined with bursting above 150% of MEOP and failure in the cylinder. The results of analysis showed that filament fiber in the cylinder should be broken at about 2088psig. From a hydraulic test the same failure mode and the level of 2200psig of burst pressure have been proved. With these results, it is verified that a filament wound case meets burst requirements.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.321-326
• /
• 2021

This paper presents a technique to minimize damaged wafers during loading. A thin wafer used in solar cells and semiconductors can be damaged easily. This makes it difficult to separate the wafer due to surface tension between the loaded wafers. A technique for minimizing damaged wafers is to supply compressed air to the wafer and simultaneously apply a small horizontal movement mechanism. The main experimental factors used in this study were the supply speed of wafers, the nozzle pressure of the compressed air, and the suction time of a vacuum head. A higher supply speed of the wafer under the same nozzle pressure and lower nozzle pressure under the same supply speed resulted in a higher failure rate. Furthermore, the damage rate, according to the wafer supply speed, was unaffected by the suction time to grip a wafer. The optimal experiment conditions within the experimental range of this study are the wafer supply speed of 600 ea/hr, nozzle air pressure of 0.55 MPa, and suction time of 0.9 sec at the vacuum head. In addition, the technology improved by the repeatability performance tests can minimize the damaged wafer rate.

• Nuclear Engineering and Technology
• /
• v.27 no.5
• /
• pp.775-783
• /
• 1995

This study is to assess the effects of increasing wall thickness on the safety margin of pressure tube in operating and of lowering initial hydrogen concentration on the DHC growth in respect to the improvement of the reliability of pressure tube in CANDU reactors. The pressure tube with thicker wall of 5.2 mm shows much higher safety margin for flaw tolerance by 25％ than the current 4.2mmm tube. The thicker pressure tubes have a great benefit in LBB assessment including the initial crack depth at which DHC occurs, the crack length at onset of leaking and the available time for action. The resistance for the pressure tube ballooning at LOCA accident is also increased with the thicker tube. The calculations for Heq concentration after 20 years of operation as a function of wall thickness and initial hydrogen concentration show that the 5.2 mm nil thickness tube with 5 ppm initial hydrogen concentration is the most resistant to DHC. with the lower initial hydrogen concentration, TSS temperature for the precipitation or hydride decreases and the crack growth during cooldown reduces.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.10a
• /
• pp.701-706
• /
• 1997

원자로 압력용기 대형 냉각재상실사고에 기인하는 노심용융물사고의 영향을 검토하기 위하여 기초적인 건전성평가를 수행하였다. 먼저 유한요소해석을 통해 노심용융물양과 경계조건 변화에 따른 원자로 압력용기의 온도 및 응력 분포를 결정하였으며, 결정된 온도와 응력 분포와 Larson-Miller 곡선과 손상 법칙을 이용하여 원자로 압력용기의 손상 정도와 파손 시간을 계산하였다. 이때 재료물성치는 기존 문헌에 제시된 온도 의존적인 값을 선정하여 사용하였으며, 노심용융물양과 경계조건이 원자로 압력용기의 건전성에 미치는 영향을 비교 고찰하여 향후 연구방향을 도출하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.3
• /
• pp.493-499
• /
• 2009

The assembled structures of pressure rice cooker are consisted of oven, top heater plate and locking ring. Since pressure is applied to the assembled structures, it should be necessary to check the safety. In this paper, structural analyses are performed from design and fracture point of view. For the design point of view, linear analysis is performed to assembled structure and for the fracture point of view, nonlinear analysis is performed to locking ring. From these results safety evaluation technique for the assembled structures of pressure rice cooker is proposed.

• Korean Journal of Food Science and Technology
• /
• v.27 no.3
• /
• pp.324-328
• /
• 1995

The changes in the rheological properties of soybean curd upon the processing conditions were measured by the failure test, and analyzed by the stress-relaxation data. Soybean curd coagulated with $CaCl_2$ showed a higher failure stress value than other coagulants such as $MgCl_2,\;CaSO_4\;and\;Glucono-{\delta}-lactone$ (GDL), whereas addition of 0.3% $CaCl_2$ produced higher failure stress value than other concentrations $0.2{\sim}0.6%)$. Also, maximum failure stress of soybean curd was shown at the higher heating temperatures$(95^{\circ}C)$ and greater molding pressures, respectively. Initial and equilibrium stress at the stress relaxation curves showed the same tendency as those of failure test, and magnitude of elastic elements$(E_0,\;E_e)$ and viscous element$({\eta})$ were numerically expressed through simple Maxwell model analysis.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.745-750
• /
• 1998

원자로 압력용기 대형 냉각재상실사고에 기인하는 노심용융사고시 노심용융물과 내벽사이의 간극 및 외벽의 열대류계수의 건전성에 대한 영향을 고찰하기 위하여 건전성평가를 수행하였다. 먼저 유한요소해석을 통해 간극 고려 여부와 외벽의 열대류계수 변화에 따른 원자로 압력용기의 온도 및 응력 분포를 결정하였으며, 결정된 온도 및 응력 분포, Larson-Miller 곡선과 손상 법칙을 이용하여 원자로 압력용기의 손상 정도와 파손 시간을 계산하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.4-4
• /
• 1999

압축가스를 이용하여 추진제를 액체 로켓 엔진에 공급하는 경우, 공급압력은 정상 연소상태의 연소압을 기준으로 하여 설계한다. 그러나 연소초기의 연소실 압력은 대기압 상태이므로 과도한 유량이 공급되어 이로 인해 hard-start 가 발생하며, 최악의 경우 엔진의 파손을 가져온다.