• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.4-4
• /
• 1999

압축가스를 이용하여 추진제를 액체 로켓 엔진에 공급하는 경우, 공급압력은 정상 연소상태의 연소압을 기준으로 하여 설계한다. 그러나 연소초기의 연소실 압력은 대기압 상태이므로 과도한 유량이 공급되어 이로 인해 hard-start 가 발생하며, 최악의 경우 엔진의 파손을 가져온다.

• International Journal of Highway Engineering
• /
• v.14 no.1
• /
• pp.35-43
• /
• 2012

The Government is implementing the safety measures for pedestrian in living zone to decrease the traffic accident casualties in half. It is urgently to study the guideline because it contains to make the guideline of a median strip in City to prevent the violation of central line and jaywalking on the main contents. So, this study analyzed the pedestrian accidents and the violation of central line, and studied the type of a median strip, the installation guideline through studying the minimum crossing. Consequently, this study found out that a median strip which revised the attention inducement stick to decrease jaywalking could not have the strong prevention function of a crash barrier, so if it happens separation after the collision between vehicles, it induced the secondary accidents, and could take negative effects on traffic safety. In consideration of driving safety, this study analyzed that if it installs a median stirp, it has to ensure one meter, and such a thing could prevent the separation of lane or damage of facilities. However, if it is hard to ensure the space because of narrow road width, it could install a median strip in case of installing the road surface mark 0.5m. And the installation of the attention inducement stick or a median strip on the central line could be possible to induce the violation of central line, thus it is desirable not to install only anythings but also raised pavement markers.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.40-44
• /
• 2015

National and international standards for curtain wall glass are focused on wind pressure and insulation performance, but disasters such as fires and earthquakes are not considered. Failure of curtain wall glass during a fire in a skyscraper increases the loss of lives and property due to the spread of fire. Therefore, the fire resistance of curtain wall glass should be investigated, and technology to prevent glass failure should be developed to prevent fire damage due to spreading fire. It is important to predict the starting point of cracks and the cause of glass failure to prevent it effectively using the limited water in a skyscraper. In this study, double glazed glass was exposed to a radiator in an experiment performed to analyze the thermal characteristics. The results show that glass that was not directly exposed to high temperature and pressure was broken. To identify this failure case, numerical analysis was performed. Three glass specimens were installed in an ISO 9705 room and exposed to radiation using a radiator, and a thermocouple was used to measure the temperature on the surface of the glass. Widely used double glazed glass was analyzed for weakness to fire.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.133-140
• /
• 2018

In this paper, we develop an automated software for in-plane structural analysis of composite laminated structures. The developed software supports various failure criteria and reports the analysis results considering user's convenience. It also provides batch job analysis function based on parallel processing technique. To verify the performance of the software, we compared margin of safety(MS) calculated in the software to those obtained from in-house method and the specimen experiment. As a result of comparisons, there was an error of less than 0.01 in the in-house method and it is within about ${\pm}10%$ with the specimen experiment. In addition, we confirmed the improvement of execution speed of batch job analysis based on parallel processing technique.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.727-734
• /
• 2014

This paper describes multi-scale based ductile fracture simulation using finite element (FE) damage analysis. The maximum and crack initiation loads of cracked components were predicted using proposed virtual testing method. To apply the local approach criteria for ductile fracture, stress-modified fracture strain model was adopted as the damage criteria with modified calibration technique that only requires tensile and fracture toughness test data. Element-size-dependent critical damage model is also introduced to apply the proposed ductile fracture simulation to large-scale components. The results of the simulation were compared with those of the tests on SA333 Gr. 6 full-scale pipes at $288^{\circ}C$, performed by the Battelle Memorial Institute.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.95-105
• /
• 2009

This study was conducted to investigate the effects of concrete flexural strength and surface smoothness, which were pay factors of concrete pavements, on pavement performance, and to develop the methodologies to determine the proper allowable ranges according to the magnitudes of those pay factors. The concrete flexural strength was analyzed using the AASHTO, power, and linear fatigue failure models, and the surface smoothness was analyzed for the roughness indices of PSI, IRI, and PrI using the AASHTO model. The analysis results showed that the allowable range of the flexural strength should be determined using the rate between the deficiency and strength, and the penalty should be linearly proportional to the strength deficiency rate because the linear relationship between the strength deficiency rate and the reduction in pavement life was observed. As the initial surface smoothness became better, the smoothness deficiency rate should be larger. The penalty due to the surface smoothness deficiency should also be linearly proportional to the smoothness deficiency rate.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.50-61
• /
• 2007

The structural stiffness, strength and stability on the bodyshell and floor structures of the Korean Low Floor Bus composed of laminate, sandwich panels and metal reinforced frame were evaluated. The laminate composite panel and facesheet of sandwich panel were made of WR580/NF4000 glass fabric/epoxy laminate, while aluminum honeycomb or balsa was applied to the core materials of the sandwich panel. A finite element analysis was used to verify the basic design requirements of the bodyshell and the floor structure. The use of aluminum reinforced frame and honeycomb core was beneficial for weight saving and structural performance. The symmetry of the outer and inner facesheet thickness of sandwich panels did not affect the structural integrity. The structural strength of the panels was evaluated using Von-Mises criterion for metal structures and total laminate approach criterion for composite structures. All stress component of the bodyshell and floor structures were safely located below the failure stresses. The total laminate approach is recommended to predict the failure of hybrid sandwich composite structures at the stage of the basic design.

• Computational Structural Engineering
• /
• v.4 no.4
• /
• pp.14-23
• /
• 1991

T/G 가동중 발생한 Gear Box 파손원인을 조사하기 위하여 실시한 현장측정결과를 이용한 결과, 다음과 같은 사실을 알 수 있었다. 1) 현장 측정치와 구조해석 결과를 토대로 판단해 볼 때 본 연구대상 구조물의 구조상 문제는 없는 것으로 판단된다. 특히 측정된 진동변위를 여러기준과 비교해 볼 때 기계 가동시 구조물에 발생하는 진동은 사람이 감지할 정도에 속한다. 2) 본 연구대상 구조물과 기계의 진동수 차가 커 공진역을 벗어나므로 기계와 구조물이 공진을 일으킬 가능성은 없으며, 감쇠비에 따른 구조물의 동적응답에는 큰 변화가 없는 것으로 판단된다. 3) 구조물설계회사에서 사용한 구조해석 모델은 근사적 모델로서 구조해석 결과 안전한 값이 얻어졌다. 따라서 이 모델을 사용하여 기초설계를 실시할 경우 안전성 문제는 없는 것으로 판단되나, 다소 경제성이 문제가 되었을 것으로 사료된다. 4) 기계제작회사에서 제시한 해석자료의 불충분으로 기계제작회사의 구조해석 모형에 대해서는 충분한 검토를 실시할 수 없었으나 기계제작회사의 해석결과를 측정치와 비교해 볼 때 측정치를 훨씬 초과함을 알 수 있었다. 이는 해석모형 작성시 구조물과 하중의 실제 상황을 제대로 반영하지 못했기 때문으로 판단되며 따라서 해석결과는 타당성이 없어 보인다. 이상의 사실을 토대로 판단해 볼 때 Gear Box 파손의 주된 원인은 구조물의 결함이라기 보다는 기계 자체의 결함인 것으로 판단되나 기계에 대한 조사는 본 연구대상이 아니므로 이에 대한 검토는 실시하지 않았다.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.365-370
• /
• 2004

Generally, component and FR-4 board are connected by solder joint. Because material properties of components and FR-4 board are different, component and FR-4 board show different coefficients of thermal expansion (CTE) and thus strains in component and board are different when they are heated. That is, the differences in CTE of component and FR-4 board cause the dissimilarity in shear strain and solder joint' failure. The first order Taylor series expansion of the limit state function incorporating with Tresca failure criterion is used in order to estimate the failure probability of solder joints under heated condition. Using shear stresses and shear strains appeared on the solder joint, we estimate the failure probability of solder joints with the Tresca failure criterion. The effects of random variables such as CTE, distance of the solder joint from the neutral point(DNP), temperature variation and height of solder on the failure probability of the solder joint are systematically studied by using the failure probability model with first order reliability method(FORM).

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.3
• /
• pp.95-105
• /
• 2019

In recent years, image processing techniques for detecting road surface damaged spot have been actively researched. Especially, it is mainly used to acquire images through a smart phone or a black box that can be mounted in a vehicle and recognize the road surface damaged region in the image using several algorithms. In addition, in conjunction with the GPS module, the exact damaged location can be obtained. The most important technology is image processing algorithm. Recently, algorithms based on artificial intelligence have been attracting attention as research topics. In this paper, we will also discuss artificial intelligence image processing algorithms. Among them, an object detection method based on an region-based convolution neural networks method is used. To improve the recognition performance of road surface damage objects, 600 road surface damaged images and 1500 general road driving images are added to the learning database. Also, supervised learning using background object recognition method is performed to reduce false alarm and missing rate in road surface damage detection. As a result, we introduce a new method that improves the recognition performance of the algorithm to 8.66% based on average value of mAP through the same test database.