• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.110-117
• /
• 2002

In a strengthened bridge deck which received increased service loads, failure patterns of bridge deck vary depending on deck thickness, compressive strength of concrete, yielding strength of reinforcement, reinforcement ratio and additional strengthening ratio. General failure pattern that is most commonly reported as punching shear failure after the main rebar yields, followed by yielding of distributing rebar. In this paper, by Proposing a limit to the amount of strengthening material, a brittle failure can be prevented and a ductile failure mode similar to that developed in unstrengthened deck is derived. In order to calculated the limit strengthening ratio, the yield line theory and previously proposed plastic punching shear model have been used

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.77-84
• /
• 2007

In this paper presented, a design method of sandwich slab bridge of simple supported made by composite materials. Many of the bridge systems, including the girders and cross-beams, and concrete decks behave as the special orthotropic plates. Such systems with sections, boundary conditions other than Navier or Levy solution types, or with irregular cross sections, analytical solution is very difficult to obtain. Thus, Finite Difference Method is used for analysis of the pertinent problem. For the design of bridge made by the composite materials, cross-section is used the form-core shape because of this shape is economical and profitable, and for output of the stress value used F.D.M. Based the experimental of a composite specialist, an equation expressing the rate of decrease of tensile strength of glass fibers based on increase of mass was obtained. From these equations, one can estimate the rate of tensile strength reduction due to increased size. Tasi-Wu failure criterion for stress space is used. Strength-failure analysis procedure, using these reduced tensile strength, is presented.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.521-524
• /
• 2011

본 논문에서는 순환골재에 대하여 구조용 적용성 검증을 목표로 하였으며, 천연골재와 순환골재 치환율에 따른 압축파괴강도와 압축강도증가에 따른 파속도의 상관관계를 비교 분석하였다. 설계기준강도 21, 27, 35MPa에 순환굵은골재 치환율 0, 30, 50, 100%를 적용하여 설계기준강도에 따른 순환굵은골재 치환율의 배합을 총 12가지로 설정하였다. 재령160일까지의 압축파괴강도의 변화를 대기양생 공시체, 수중 양생공시체 그리고 코어공시체를 이용하여 비교하였고, 모의부재(800${\times}$800${\times}$200mm)를 통하여 재령160일까지의 초음파속도를 측정하였다. 압축파괴실험을 통하여 취득한 데이터를 비교해 본 결과 순환굵은골재 치환율에 따른 강도저하현상은 나타나지 않았다. 또한, 재령일에 따른 강도 증가와 함께 파속도도 같이 증가함을 알 수 있었다.

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.44-57
• /
• 1992

본 보에서는 용접 구조물의 파괴 방지를 위한 제반 용접 구조 설계에 대하여 전반적으로 기술 하였다. 현대 용접 구조물의 각 선급이나 spec.에서 규정한 식들에 의해 산정된 정적하중으로 구조 설계되는 종래의 방법과는 달리, 유한 요소 구조 해석에 의한 강도 평가, 외부하중의 직접 계산에 의한 보다 정확한 설계 하중의 설정 및 통계적 처리를 통한 합리적인 구조해석(피로강도 포함)등으로 설계되고 있다. 더우기 구조설계시 구조물의 취성파괴를 고려한 파괴강도 및 인성 개념을 도입하였을 뿐 아니라 균열의 존재와 성장을 파괴 역학적으로 해석하여 구조물의 조업 중에서의 파괴관리 및 제어도 실시할 수 있는 총합적인 설계에 의하여 용접 구조물은 제작되고 있다. 비록 구조물의 총합적인 구조 설계로 제작되었을지라도, 구조물의 사용 성능은 용접부의 특성에 의하여 크게 변하게 되므로 용접 설계의 역할을 매우 중요하다. 용접 설계란 용접시공법, 구조부재 및 용접재료의 선정, 용접 이음부의 구조적 형상과 세부 형상 및 그외 용접에 관련된 제 인자들을 상호 유기적으로 조합함으로써 보다 경제적이고 신뢰성 있는 용접부를 얻고자 함에 그 목적이 있다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.3
• /
• pp.33-44
• /
• 1999

An energy balance procedure is developed to incorporate the effects of earthquake duration which involves the effect of cyclic loading and the corresponding cumulative plastic deformation. Particular emphasis is given to the flexural failure of non-seismically designed columns of reinforced concrete frames. For this, conceptual strength deterioration models for columns, governed by concrete, anchorage failure and longitudinal steel fracture due to low-cycle fatigue, are proposed. It is evident that the energy-based method has good agreement with the experimental data and is able to predict the failure mode.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.157-162
• /
• 1997

Silicon Nitride samples with different microstructure were prepared by hot pressing and subsequent heat treatment under N2 gas pressure. The fracture toughness (KIC)of Si3N4 increased with the increase of grain size, but the bending strength of plain specimen($\sigma$F) decreased. The relation between fracture stress($\sigma$c) and equivalent crack length(ae) agreed well with the calculated values by process zone size failure criterion. A probabilistic failure assessment curve is proposed based on both statistical character of $\sigma$F and KIC.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.6
• /
• pp.165-174
• /
• 1997

고강도 및 보통강도 콘크리트의 압축파괴 거동에 영향을 미치는 요소들 (재료의 강도, 시편의 세장비, 전단구속, 실험장치의 강성, 피드백 신호)에 관한 연구가 수행되었다. 피드백 신호로 자동 조절되는 유압 실험기계항에서 원주변형 피드백 신호를 사용하여 연화곡선을 구했다. 재하장치로부터의 단부 전단 구속을 줄이면 제한된 영역 안에서 재하방향 균형이 형성되고, 또한 연화곡선의 경사가 급해지고 파괴에너지도 작아진다. 이때 길이가 큰 시편에서 파괴에너지가 커지는 것은 안장과는 달리 단순균열이 형성되는 것이 아니고 , 파괴가 용적을 가진다는 것을 의미한다. 압축응력하의 국부 파괴는 재료특성이 아니므로, 단부 전단구속이 없더라도 재료적 특성으로서의 응력-변형도 곡선은 정하기 어렵다.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.3 s.76
• /
• pp.271-283
• /
• 2005

This paper concerns the prediction of shear capacity, as governed by steel failure and concrete breakout failure, of set anchors installed in plain concrete. For this purpose, the methods to evaluate the shear capacity of the set anchors in concrete are summarized and the experimental data are compared with capacities by the two present methods : the method of ACI349-90 and the Concrete Capacity Design (CCD) method. (1) The constant-0.684 in the steel strength equation of set anchor was determined from shear test data at the 5 percent fractile probability. Consequently, it was concluded that the constant-0.6 and 0.5 in the steel strength equation for steel failure of ACI318-02 and EOTA were safe. The nominal shear strength of set anchor was proposed as following. $V_s=0.684 A_{se}f_{ut}$. (2) The CCD method was considered reasonable in estimating the concrete breakout strength of set anchors. In terms of the CCD method, the nominal concrete breakout strength of set anchor in shear was provided as follows; $V_b=0.609(\frac{\iota}{d_o})^{0.2}\sqrt{d_0}\sqrt{f_c}(c_1)^{1.5}$(N). (3) The CCD method was considered reasonable in estimating the concrete breakout strength for spacing of set anchors. The proposed equation was considered safe in estimating the concrete breakout strength for spacing of set anchors.

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.683-691
• /
• 2013

Failure behaviour of deep beams is largely depend on shear span to effective depth ratio(a/d). For deep beams with $a/d{\leq}1.0$, the diagonal splitting of the web and local crushing of concrete near applied loads or supports is the most common failure mode. If the beam contains sufficient web reinforcement, area of local crushing will be increased while area of diagonal splitting is decreased. When web reinforcement above purpose, web should be reinforced both in the horizontal and vertical directions or be reinforced in perpendicular direction to diagonal cracks. For deep beams with 1.0${\leq}2.5$, the increment of shear strength by the horizontal web reinforcement are hardly expected unless amount of main bars very small that the main bars should be reached yielding state when shear failure occurs. In contrast, the vertical web reinforcement prevent the beam from being transferred to tied arch mechanism, and as a result th shear strength of beam increase. In this study, formulas based on upper bound theorem of plastic theory are proposed to predict the shear strength of reinforced concrete deep beams with $a/d{\leq}1.0$. Comparisons with other experiment results are performed, and good agreement between measured and predicted value by proposed formulas is obtained.

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.383-391
• /
• 2013

A number of true triaxial tests on rock samples have been conducted since the late 1960 and their results strongly suggest that the intermediate principal stress has a considerable effect on rock strength. Based on these experimental evidence, various 3-D rock failure criteria accounting for the effect of the intermediate principal stress have been proposed. Most of the 3-D failure criteria, however, are focused on the phenomenological description of the rock strength from the true triaxial tests, so that the associated strength parameters have little physical meaning. In order to confirm the likelihood that the intermediate principal stress dependency of rock strength is related to the presence of weak planes and their distribution to the preferred orientation, true triaxial tests are simulated with the transversely isotropic rock model. The conventional Mohr-Coulomb criterion is extended to its anisotropic version by incorporating the concept of microstructure tensor. With the anisotropic Mohr-Coulomb criterion, the critical plane approach is applied to calculate the strength of the transversely isotropic rock model and the orientation of the fracture plane. This investigation hints that the spatial distribution of microstructural planes with respect to the principal stress triad is closely related to the intermediate principal stress dependency of rock strength.