• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2001.02a
• /
• pp.3-9
• /
• 2001

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.07a
• /
• pp.9-14
• /
• 2000

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1998.12a
• /
• pp.16-22
• /
• 1998

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.216-223
• /
• 1999

This study was intended to determine the inertia , damping and stiffness properties of the cab-suspension of agricultural tractors by applying the direct system identification method (DSIM). Since the rigid and elastic modes of the cab-suspension are not likely to be separated clearly, direct application of the DSIM may result in large computation error. To solve such a problem, a method of locating mass center of the cab were determined by assuming the behavior of the cab-suspension is a rigid body motion. The dynamic parameters of the cab-suspension were then determined by applying the DSIM with the known coordinates of the mass center. The constraints of spatial matrices of the cab-suspension also make the algorithm for the DSIM perform better. The values of dynamic parameters determined by this method agreed well with those determined by the experiment.

• Journal of Biosystems Engineering
• /
• v.20 no.2
• /
• pp.117-126
• /
• 1995

High level of tractor noise may reduce operator's work performance and cause a hearing problem. This study was carried out to investigate the cab noise of a selected agricultural tractor. The noise was measured and analyzed in terms of sound and sound intensity levels. Form the results it was known that a structure-born noise was induced from the feet-rest and rear floor panel of the cab. The air-borne noise caused mainly by the engine was transmitted into the operator's position through the small openings of cab structures in the operator's lower front area.

• Journal of Biosystems Engineering
• /
• v.20 no.2
• /
• pp.127-132
• /
• 1995

In the first part of this paper, an analysis of the cab noise of a selected agricultural tractor was presented. In this study, using the results of the previous analysis, two passive noise control measures of the sound insulation and absorption were conducted to reduce the noise level inside the cab. These measures of noise control reduced the total noise level by 6.2㏈(A) at the operator position inside the cab. In order to further reduce the cab noise, particularly, of lower frequencies than 630Hz, stiffness and damping of the floor panel should be enforced. It was also suggested that a proper suspension for the cab mounting is necessary to reduce the level of structure-born noises.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1999.12a
• /
• pp.85-91
• /
• 1999

• Journal of Biosystems Engineering
• /
• v.23 no.4
• /
• pp.327-334
• /
• 1998

This work was intended to determine the optimum values of the cab suspension parameters by a simulation method in order to minimize the seat accelerations of agricultural tractors in the frequencies lower than 50Hz. A dynamic model of cab motions was developed and verified using a tractor excited over half-sine bumps on a concrete test road. A simulation program based on the model was also developed. A method was proposed to determine the optimum values of the suspension parameters. It was found that the natural frequencies of the cab and seat suspensions must be apart as far as possible until the sum of seat and cab accelerations is minimized, which also reduces the seat accelerations maximally.

• Journal of Biosystems Engineering
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2009

In order to evaluate environmental comfort of tractor cabs, temperature, relative humidity and noise within the cab were taken from 31 tractors during plowing and rotovating operations. The temperature and humidity were evaluated with regard to the comfort zone of KS B ISO 14269-2 and PMV of ISO 7730. The noise was evaluated with regard to the permissible sound level of OSHA for daily exposure of 8 hours. The collected data indicated that thermal environment of the cabs was out of the comfort zone, which meant tractor operators worked under uncomfortable thermal conditions. Difference in the thermal comfort by tractor power and maker, and type of works was not found. However, 25% of the studied tractors showed PMV in a range of -0.5 to +0.5, which indicated their operators worked under the comfort criteria. PMV was improved when the cab was air-conditioned. Levels of measured cab noise were lower than the permissible criteria, and 76.7% of the studied tractors had cab noise ranged from 75 to 85 dBA. There was a tendency that high powered tractors, rotovating operations and locally-made tractors had greater cab noise levels. However, their differences were insignificant.