• Tribology and Lubricants
• /
• v.17 no.4
• /
• pp.312-320
• /
• 2001

In magnetic hard disk drives, higher areal recording density requires reduction of head-disk spacing. To overcome the increase of stiction associated with reduction of head-disk spacing, a padder slider, which adds pads to slider's air bearing surface, can be one of the practical solution for sub 20 nm flying height, and even for near contact recording. This study investigated the tribological characteristics of a padder slider. A padder slider took off slowly but showed less friction force than a normal slider. The hot/dry CSS test and drag test indicated that pad wear of a padder slider was negligible. The tribological performance of disk is an important factor to be considered. In particular, less carbon overcoat layer of the disk will result in higher stiction and wear in slider/disk interface. In conclusion, a padder slider shows encouraging tribological performances for practical use in HDD.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.381-388
• /
• 2000

Boundary lubrication condition arises in most lubricated systems, especially during motion reversals and start up phase of operation. In this work electric contact resistance variations with respect to sliding conditions under lubrication is investigated. The motivation was to improve the understanding of the contact condition in the boundary lubrication regime. It is shown that electrical contact resistance is sensitive to sliding speed and surface condition of the specimens. Also, phenomena such as run-in during the initial phase of sliding and lubricant pile up near the sliding pin could be observed. The results of this work will aid in better understanding of the metal to metal contact condition in lubricated systems.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.127-134
• /
• 2001

Nano adhesion and friction between a Sj$_3$N$_4$ AFM tip and thin silver films were experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes in various ranges of normal load. Thin silver films deposited by IBAD (ion beam assisted deposition) on Si-wafer (100) and Si-wafer of different surface roughness were used. Results showed that nano adhesion and friction decreased as the surface roughness increased. When the Si surfaces were coated by pure silver, the adhesion and friction decreased. But the adhesion and friction were not affected by the thickness of IBAD silver coating. As the normal force increased, the adhesion forces of bare Si-wafer and IBAD silver coating film remained constant, but the friction forces increased linearly. Test results suggested that the friction was mainly governed by the adhesion as long as the normal load was low.

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.188-193
• /
• 2000

An experimental study was performed to discover the effect of environment on the tribological behavior of Si-incorporated diamond-like carbon(Si-DLC) film slid on a steel ball. The films were deposited on Si(100) wafers by a radio-frequency glow discharge of mixtures of benzene and dilute silane gases. Experiments using a ball-on-disk test-rig was performed in vacuum, dry air and ambient air conditions. It was observed that coefficient of friction decreased as the environment changed from vacuum, to dry air. Chemical analyses of debris suggested that low and stable friction is closely related to the formation of silicon-rich oxide debris and the rolling action.

• Tribology and Lubricants
• /
• v.25 no.1
• /
• pp.25-30
• /
• 2009

본 연구에서는 pin-on-disk 마찰 시험기를 통하여 Hexagonal 배열 $40{\mu}m$ Dimple 패턴의 효과를 실험하였다. 마찰 실험은 미끄럼 속도가 $0.06{\sim}0.34m/s$로 하였으며 마찰하중은 $20{\sim}100\;N$의 범위로 하였고, Dimple의 밀도는 $10{\sim}25%$의 범위로 제작하여 실험을 행하였다. 일반적으로 속도가 증가하고 하중이 감소할수록 마찰계수는 감소하는 경향을 나타내었으며, Dimple에 의한 마찰저감 효과는 속도가 $0.14{\sim}0.26m/s$의 범위에서 나타났다. $40{\mu}m$ Hexagonal 배열 Dimple 패턴의 마찰 특성에서는 밀도가 12.5%에서 가장 좋은 경향을 나타내었다.

• Tribology and Lubricants
• /
• v.24 no.5
• /
• pp.241-249
• /
• 2008

This paper describes the tribological effects on the nonlinear behavior of a spur gear pair with one-way clutch according to the direct contact elastic deformation model over a wide range of speeds, considering the hydrodynamic effects. The effects of various lubrication parameters, such as viscosity, film width, and friction, on the nonlinear dynamic behavior were analyzed. Forces due to the entraining velocity and the hydrodynamic friction were about two orders smaller than normal forces over the whole speed range. While the viscosity has a strong effect on the behavior of gear pair systems, friction has very little effect on torsional behavior. The inclusion of the hydrodynamic effect facilitates nonlinearity by increasing the overlap and damping, as well as decreasing elastic deformation and tooth reaction forces.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.115-116
• /
• 2012

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.219-225
• /
• 2013

In this study, the tribological characteristics of silver films that were deposited on a glass substrate by electroless plating were investigated. The electroless-plating method has many notable advantages. It is easy and economical to obtain solid films using this coating process, and it can be applied to both nonconducting and conducting substrates. In this study, silver was selected as the electroless-plating material because it is one of the most common materials used as a solid lubricant. The mechanical properties of silver electroless-plated specimens were investigated for various coating conditions. The thickness of the coating could be controlled by varying the electroless-plating time. The properties of the coatings were investigated using AFM, SEM, and a tribotester.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1238-1245
• /
• 1988

Friction and wear characteristics of short fiber reinforced and particulate filled composites were investigated experimentally. Two kinds of fiber composites, chopped graphite fiber reinforced PAI(polyamide-imide) and glass fiber reinforced PAI, and a particulate composite, TiO$_{2}$ powder filled PAI, were selected for the friction and wear test since these are important engineering materials based on a new high temperature engineering plastic. All the specimens were cut into proper size for cylinder-on-plate type wear test. Frictional forces were measured by employing a load transducer and wear rates were calculated by measuring weight loss during wear test. The experimental results are reported in this paper and carefully discussed to explain the friction and wear behavior qualitatively. The frictional behavior is interpreted by considering four basic friction components which are believed to the genesis of friction and the wear behavior is explained by applying delamination theory of wear.

• Journal of the Korean Society for Railway
• /
• v.15 no.3
• /
• pp.224-230
• /
• 2012

The wearing slider of the rail motor car's pantograph is considerable changed by the type and the material properties. Especially, precipitation and arc influences are main factors decided to life time of wearing slider and contact wire. This study is wearing phenomenon analysis of Cu-type wearing slider with high electric conductivity and resistance arc through experiment by running train. Author observed that wearing phenomenon of Cu-type wearing slider with normal and abnormal wearing characteristics and comparatively analysis precipitation, mileage and weight influences of exchanged Cutype and Fe-type wearing sliders. In this paper result showed that necessity for the application which is the Fe-type of wearing slider had superior wear resisting capacity etc., through tribology approach.