• Journal of Energy Engineering
• /
• v.6 no.2
• /
• pp.212-219
• /
• 1997

The objective of this study is to investigate the effects light diesel-water emulsified fuel on performance and exhaust emissions of the compression ignition engine. The experimental results of light diesel-water emulsified fuel operation with new type ultrasonic emulsification apparatus as compared with light diesel operation are very positive; maximum 28% reduction of SFC (in the case of 30% of water content), maximum 60% reduction of smoke (in the case of 30% of water content), maximum 79% reduction of CO emission (in the case of 30% of water content). However, comparing light diesel-water emulsified fuel and light diesel in the same engine under the same operating conditions, power and torque were lower in the case of emulsified fuel. In view of the results for the above mentioned, the mixing of water into light diesel in the form of emulsification proved to be the best means for reduction of specific fuel consumption and exhaust emissions of C.I. engines.

• Journal of Astronomy and Space Sciences
• /
• v.25 no.4
• /
• pp.481-490
• /
• 2008

Reaction wheel is one of the actuators for spacecraft attitude control, which generates torque by changing an inertial rotor speed inside of the wheel. In order to generate required torque accurately and estimate an accurate angular momentum, wheel speed should be measured as close to the actual speed as possible. In this study, two conventional speed detection methods for high speed motor with digital tacho pulse (Elapsed-time method and Pulse-count method) and their resolutions are analyzed. For satellite attitude maneuvering and control, reaction wheel shall be operated in bi directional and low speed operation is sometimes needed for emergency case. Thus the bias error at low speed with constant acceleration (or deceleration) is also analysed. As a result, the speed detection error of elapsed-time method is largely influenced upon the high-speed clock frequency at high speed and largely effected on the number of tacho pulses used in elapsed time calculation at low speed, respectively.

• The korean journal of orthodontics
• /
• v.35 no.6 s.113
• /
• pp.485-494
• /
• 2005

Maxillary anterior teeth were intruded and lingually root torqued with two maxillary anterior microimplants between the lateral incisors and canines. Overerupted maxillary canines were intruded with two other microimplants between the maxillary canines and first premolars. Maxillary posterior teeth and canines were distalized, then the maxillary incisors were retracted with two maxillary posterior microimplants between the first and second molars. The mandibular anterior teeth were intruded and the mandibular posterior teeth were extruded with conventional method such as anterior bite plane, intrusion arch and Class II elastics. The mandible moved slightly forward after the correction of deep bite and retroclination of the upper incisors. Consequently, microimplant anchorage (MIA) provided absolute anchorage for simultaneous correction of Class II canine and molar relationships and deep overbite.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.80-88
• /
• 2003

In this paper, the new robust torsional vibration suppression control scheme is proposed for the two mass system. A reduced order state feedback controller where the motor speed and the observed torsional torque are fed back and the PI controller are proposed as the torsional vibration suppression controller. Using the estimated mechanical parameters by off-line RLS(Recursive Least Square) algorithms, the speed controller for torsional vibration suppression is designed and its gains are determined using the Kharitonov robust control theory. The Kharitonov robust control theory can obtain the robust stability with a specified stability margin and a damping limit and the good performance of vibration suppression although if the parameters are varied within some specified limit. The effectiveness and usefulness of the proposed schemes are verified with the simulation and the experimental results on the fully-digitalized 5.5kW two mass system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.11
• /
• pp.1147-1152
• /
• 2004

The objective of this work is to develop a new design method to find optimal coils, especially the optimal coil configuration of an optical pickup actuator. In designing actuator coils, the developed Lorenz force in the coils along the desired direction should be made as large as possible while forces and torques in other directions should be made as small as possible. The design methodology we are developing is a systematic approach that can generate optimal coil configurations for given permanent magnet configurations. To consider the best coil configuration among all feasible coil configurations, we formulate the design problem as a topology optimization of a coil. The present formulation for coil design is noble in the sense that the existing topology optimization is mainly concerned with the design of yokes and permanent magnets and that the optimization of actuator coils is so far limited within shape or size optimization. Though the present design methodology applies to any problem, the specific design example considered is the design of fine-pattern tracking and focusing coils.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.11
• /
• pp.179-185
• /
• 2020

In this paper, we propose impact factors and validity of blood variables on death of COVID-19 patients. The clinical-epidemiological data of 5628 COVID-19 patients, provided from Korea Disease Control and Prevention Agency as day of 30th April 2020, were used. As results, impact factors of death were dementia, older age, high lymphocyte, cancer, dyspnea, COPD, change of consciousness, heart disease, high platelets, abnormal diastolic pressure and fever. The validities of blood variables for death were high in the order of lymphocyte, hemoglobin, hematocrit, platelet and WBC. Therefore, risk factors such as initial clinical characteristics, underlying disease and blood test results, could be regarded for efficient management of COVID-19 patients.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.2 s.314
• /
• pp.24-31
• /
• 2007

This paper presents self tuning PI(STPI) controller of IPMSM drive using neural network. In general, PI controller in computer numerically controlled machine process fixed gain. They may perform well under some operating conditions, but not all. To increase the robustness of fixed gain PI controller, STPI controller proposes a new method based neural network. STPI controller is developed to minimize overshoot, rise time and settling time following sudden parameter changes such as speed, load torque and inertia. Also, this paper is proposed speed control of IPMSM using neural network and estimation of speed using artificial neural network(ANN) controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The results on a speed controller of IPMSM are presented to show the effectiveness of the proposed gain tuner. And this controller is better than the fixed gains one in terms of robustness, even under great variations of operating conditions and load disturbance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.731-738
• /
• 2013

This paper describes a fault-tolerant driving control strategy for an independent steer-by-wire system in sixwheel-drive/six-wheel-steering vehicles. An algorithm has been designed to realize vehicle maneuverability that is as close as possible to that of non-faulty vehicles by inducing high slip ratio of the wheel through a faulty steer-by-wire system in order to reduce the lateral tire force, which is resistant to the yaw motion. Considering the transition of the longitudinal tire force of a wheel with a faulty steer-by-wire component, the longitudinal tire forces are optimally distributed to the other wheels. Fault-tolerant driving performance has been investigated via computer simulations. Simulation studies show that the proposed algorithm can significantly improve the maneuverability of a vehicle with a faulty steer-by-wire system as compared to the optimal traction distribution method.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.385-391
• /
• 2005

Reactive melt processing has been carried out to investigate crosslinking characteristics of high density polyethylene OTDPE) with dicummyl peroxide (DCP) and perbutyle peroxide (PBP). The increase of torque in the internal mixer indicated that the crosslinking in HDPE has been occurred by peroxides. As a result, the substantial decrease of density, melting temperature, and melt enthalpy were found while the melt viscosity increased in partially crosslinked HDPE. In the mechanical properties of partially crosslinked HDPE, the increase of maximum strength and the decrease in elongation at break were clearly noticed and these were more pronounced when PBP was applied as a crosslinking agent. It seems that the maximum strength was obtained with reactive processing temperature at $150^{circ}C$, however, the mixing time did not affect to the strength of partially crosslinked HDPE.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.2
• /
• pp.61-70
• /
• 2013

Hydrodynamic aspects on three-dimensional effects were investigated in this study for simple and convenient conversion of tidal stream energy using a Vertical-Axis Turbine (VAT). Numerical approach was made to reveal the differences of flow physics between 2-D estimation and rigorous 3-D simulation. It was shown that the 3-D effects were dominant mainly due to the variation of tip vortices around the tip region of rotor blade, causing the loss of lift for steadily translating hydrofoil and the reduction of torque for rotating turbine blade. The 3-D effect was found to be rather prominent for the typical VATs considered in this paper. Simple and yet efficient 2-D approach with the correction of its three-dimensionality was also proposed for practical design and analysis of VAT.