• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.135-137
• /
• 2007

In this paper, an advanced torque control scheme of SRM using DITC(Direct Instantaneous Torque Control) and PWM(pulse width modulation) is presented. Different from conventional DITC method, proposed method uses one or two switching modes at every sampling time, instead of only one switching mode. The duty ratio of the phase switch is regulated according to the torque error and simple control rules of DITC. Moreover the sampling time of control can be extended, which allows implementation on low cost microcontrollers. The proposed control method is verified by the simulations and experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.196-201
• /
• 2008

This paper is about electromagnetic vibration source in outer rotor type of BLDC motors. Experiments are carried out with three pole-slot combinations which are 6 slots, 12 slots, and 24 slots with 4 poles rotor. According to results, vibration sources separate into electromagnetic and mechanical factors. Using the finite element method (FEM), It is analyed that vibration characteristics of electromagnetic source in each type. This paper shows electromagnetic sensitivity to vibration, and introduces necessary point in lower vibration motors. Also rotor balance is important to prevent uneven distribution of magnetic flux between rotor and stator.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.734-736
• /
• 2015

본 논문은 비균일 공극형 단상 4/4극 하이브리드 스위치드릴럭턴스 전동기(이하, HSRM)를 제안한다. 제안된 HSRM의 회전자 형상은 비균일한 공극을 갖는 형상으로 데드존 구간과 토크리플, 출력특성에 기여한다. 이와 같은 특성을 검증하기 위해 균일한 공극을 갖는 단상 하이브리드 SRM의 토크 및 출력특성을 유한요소해석(FEA)을 통해 비교하였다. 그 결과 제안된 HSRM을 제작하였고 시험 결과를 통해 그 타당성을 검증하였다.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2021-2023
• /
• 2001

Switched Reluctance Motor(SRM) Drive 회로의 경제성과 효율성을 감안하여 본 논문에서는 범용적으로 많이 쓰이는 비대칭 컨버터와 변형된 C-dump 컨버터를 비교 분석하였으며 산업용 저전압 SRM에 각각 적용하였을 때의 특성들을 기술하였다. 고속도 영역과 저속도 영역에서의 Advance angle과 Firing angle 제어를 하였을 때의 토크특성과 전류특성을 비교하였다. 또한, PWM 을 이용하여 토크리플을 감안한 적절한 on-off 각을 제시하여 그에 따른 저속도 영역에서의 특성들을 기술하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1923-1929
• /
• 2009

The design of SPMSM(surface mounted permanent magnet synchronous motor) has been performed to reduce cogging torque and torque ripples. In general, cogging torque and torque ripples are affected by the shapes of teeth width, yoke depth, magnet pole arc, etc. Particularly, the minimum design point of cogging torque and torque ripples are different so that the design of SPMSM should be done to compromise both of them for precision application. In this paper, the design of PMSM for EPS(electric power steering) system is performed to verify the validity, and the design characteristics versus teeth width, yoke depth, and magnet pole arc are investigated in order to find out the minimum point of cogging torque and torque ripples. In addition, skew of PM is applied for cogging torque reduction.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.142-145
• /
• 2001

In this paper the electromagnetic torque developed in IPMSM(Interior Permanent Magnet Synchronous Motor) is analyzed. If flux distributions in the motor are not sinusoidal, a sinusoidal current produces important torque ripple. Torque ripple causes vibration and noise of motors. The optimized current waveforms for ripple free is able to be obtained by analysis of Back-EMF and torque equation. The method to find the optimal current is based on numerical predetermination. In this paper proposes current waveform which can eliminate the torque ripple, and the validity is verified through the simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2618-2624
• /
• 2009

Harmonics (or distortion in wave form) has always existed in electrical power systems. It is harmless as long as its level is not substantial. However, with the recent rapid advancement of power electronics technology, so-called nonlinear loads, such as variable frequency drives for motor power/speed control, are increasingly finding their way to shipboard or offshore applications. In this paper a new approach to direct torque control (DTC) of induction motor drive is presented. In comparison with the conventional DTC methods the inverter switching frequency is constant and is dramatically increased, requiring neither any increase of the sampling frequency, nor any high frequency dither signal. The well-developed space vector modulation technique is applied to inverter control in the proposed DTC-based induction motor drive system, thereby dramatically reducing the current harmonics. As compared to the existing DTC approach with constant inverter switching frequency, the presented new approach does not invoke any concept of deadbeat control, thereby dramatically reducing the computations.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.5
• /
• pp.14-21
• /
• 2002

This paper did the study target for modeling, characteristics analysis and harmonic reduce with the detent torque of a 4 phase and 5 phase hybrid type step motor. For this, it was attempted to derive the mathematical modeling and used the permeance method for flux field analysis. Through this analysis result, this paper acquired the detent torque of this model. To compare the characteristics analysis of phase difference with two motors structure it have obtained to derive the operating detent torque with this model. Here, 5 phase motor has known the harmonic reduce of detail torque compare with 4 phase motor. Also, that has showed to improved the step response. The analysis result has represent the effect that a fundamental component of the permeance distribution produces the average torque and that harmonic components produce the ripple torque.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.112-118
• /
• 2004

Recently, development of rare earth permanent magnet with the high remanence, high coercivity allows the design of brushless motors with very high efficiency over a wide speed range. Cogging torque is produced in a permanent magnet by magnetic attraction between the rotor mounted permanent magnet and the stator teeth. It is an undesired effect that contributes to output ripple, vibration, and noise of machine. This cogging torque can be reduced by variation of magnet arc length, airgap length, magnet thickness, shifting the magnetic pole and varying the radial shoe depth and etc. In this paper, some airgap length and magnet arc that reduce cogging torque are found by finite element method(FEM) and Maxwell stress tensor method. The SPM(Surface Permanent Magnet) type of high-power Brushless DC (BLDC) motor is optimized as a sample model.

• Journal of the Korean Magnetics Society
• /
• v.24 no.5
• /
• pp.160-164
• /
• 2014

In this paper, an efficient robust design utilizing an enhanced Taguchi method is proposed to reduce cogging torque of a BLDC motor in the presence of design uncertainty. To overcome defects of the conventional Taguchi method in dealing with a generalized robust design problem, a penalty function and an optimal level searching technique are newly introduced. In order to verify the proposed method, a 5 kW, rated speed of 2,300 rpm, rated torque of 20 Nm BLDC motor for driving electric vehicles is optimized. Then, the robust design is compared with conceptual and deterministic ones in terms of the cogging torque, rated torque and torque ripple.