• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.04a
• /
• pp.32-38
• /
• 1993

최적의 회전기계 시스템을 설계하기 위해서는 시스템의 운전특성에 적합한 제어링이 선정$\cdot$설계되어져야 한다. 그러기 위해서는 회전 기계에 사용되는 베어링의 운전특성을 잘 예측하는 것이 무엇보다도 중요하다. 대형 틸팅패드 저어널베어링은 고속안정성 특성이 우수한 베어링으로서 터빈발전기 등 대형 고속 회전기계에 널리 사용되고 있다. 하지만, 틸팅패드 저어널베어링은 구조가 복잡하고 경계조건 선정이 까다로와서, 동 베어링에 대하여 여러 논문들이 발표되어 왔지만, 대부분의 결과들이 특정한 가정을 이용하여 정성적인 경향만 제시하고 있다. 다라서 대형 틸팅패드 저어널베어링의 보다 엄밀한 성능예측을 위해서는 실제 운전조건에 적합한 경계조건을 제시하기 위한 실험적 연구가 우선적으로 요구되고 있다. 본 실험 연구에서는 대형 틸팅패드 저어널베어링에서 선단압력 발생에 대하여 실험적으로 관찰함으로써 동 베어링의 성능에 미치는 선단압력의 효과와 압력 및 무부하측패드의 거동에 대한 경계조건을 실험적으로 제시하고자 한다.

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.114-122
• /
• 2007

This paper addresses the measurement of structural loads on the Unison U50 wind turbine. The load measurement are carried out to determine the actual loads acting on a wind turbine. This is needed not only the certification process but also improving the technical development for prototype wind turbine. The measurement system is consists of measuring load, operating quantities and meteorological signal. All data that occur during the operating of a WT are stored the data acquisition system automatically. With using the measured data, load spectrum and equivalent load are evaluated according to IEC61400-13 "Measurement of mechanical loads".

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.882-883
• /
• 2011

This paper deals with comparison on Electromagnetic losses of slotted and slotless high-speed PM Machine for Micro Turbine. Losses are consist of core losses, copper losses and eddy current losses. We are using both analytical method and 2D Finite Element Method for more detailed losses analysis. And then We compare Electromagnetic losses of slotted and slotless PM synchronous machine. This machine has designed of a generator of 800W, 400000rpm and a starter of 400W, 200000rpm.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.152-153
• /
• 2011

원자력발전소(원전) 터빈발전기에서 생산된 전력은 송전망과 발전소 운전에 필요한 기기 작동을 위해 소내로 공급되도록 설계되어 있다. 최근 신규원전의 전원 공급을 위해 가동중 원전의 송전선로 휴전 작업시 운영기술지침서의 운전제한시간을 초과한 휴전작업에 대한 안전성 문제가 대두되었다. 본 논문에서는 정상운전중인 원전의 송전선로 1개 휴전 작업중 운전중인 송전선로 상실시 리스크를 분석하여 허용기준 만족 여부를 평가하고, 리스크관리 대책을 수립하여 전력계통의 신뢰성 및 안전성 향상에 기여하고자 한다.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.1
• /
• pp.5-10
• /
• 2011

MTG(Micro turbine generator) operating at 400,000 rpm is under development and the impact test rig to measure the dynamic stiffness and damping coefficient of air foil bearing for high speed rotor is presented in this study. The stiffness and damping coefficient of air foil bearing depending on the rotational speed can be measured easily and effectively by using the simple configuration of impact test rig which is composed of air gun, gap sensors and high speed motor. The estimation results of stiffness and dampling coefficient using least square estimation method is presented as well.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.10
• /
• pp.159-165
• /
• 2007

This paper presents a method for the derivation of model parameters of a co-generation system using data measured through on-site generator characteristic testing and validates its model parameters. Dynamic models such as generator, excitation system, and turbine/governor are mainly dealt in this paper. For the purpose of validation of derived model parameters, the measured results are compared with simulation results. The comparisons between measured results and simulation results show good match.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.8
• /
• pp.1555-1559
• /
• 2011

Turbine generator(13.8 kV, 137.5 MW) has high bearing vibration at rotation speed. Shorted turns in generator rotor windings have strong correlation with increased field current which is thus related to increase in bearing vibration. The recurrent surge oscillograph (RSO) test is performed on the rotor winding in turbine generator to detect shorted turns. The result of the RSO test indicates that shorted turns of rotor winding are generated in two locations. The RSO test was capable of identifying the presence, number, and location of shorted turns in generator rotor windings.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.8
• /
• pp.1423-1428
• /
• 2010

The results of off-line and on-line diagnostic tests performed on the stator winding of an air-cooled gas turbine(G/T) generator are reported in this paper. Off-line diagnostic tests included measurements of the ac current, dissipation factor(tan${\delta}$), and partial discharge(PD). Six epoxy-mica capacitors were installed in the three phases of G/T generator for performing on-line diagnostic testing with the turbine generator analyzer(TGA). The TGA showed that the normalized quantity number(NQN) and the PD magnitude($Q_m$) were high in phase A of the stator winding. Internal discharges were generated in phases B and C, and slot discharge occurred in phase A. According to the trend analyses of the NQN and $Q_m$ values available for insulation condition assessment for G/T generator stator windings, it was concluded that phases B and C were in good condition, whereas phase A has been significantly deteriorated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1818-1821
• /
• 2008

Several off-line diagnostic tests which include the insulation resistance(IR), polarization index(PI), low-voltage AC, and recurrent surge oscillograph(RSO) tests were performed to assess the condition of generator rotor windings. The low-voltage AC and the RSO tests were performed on the gas turbine generator rotor winding to detect shorted turns. Before intentionally applying artificial shorted faults, it was confirmed by the low voltage AC and the RSO tests that the winding was in sound condition. For simulated shorted rotor winding turns, the RSO test detected the fault in the winding. The RSO test was capable of identifying the number and pole location of the shorted turns for a number of simulated shorted coils.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.504-507
• /
• 2009

The purpose of this work is to predict the low frequency aero-acoustic noise generated from the horizontal axis wind turbine, NREL Phase VI using large eddy simulation and Ffowcs-Williams and Hawkings model provided in the commercial code, FLUENT. Calculated aerodynamic performances such as shaft torque and power are compared with experimentally measured value. Performance results show a good agreement with experimental data within about 0.8%. If the distance by two times is changed from 32D to 64D toward the downstream region, sound pressure level is reduced by about 6.4dB.