• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.9
• /
• pp.1-10
• /
• 2006

An optimization study on a small turbopump impeller operating at the low specific speed is conducted to obtain high output head at the impeller exit. Its specific speed in SI unit (RPM, m3/sec, m) is 4.0, and the outer diameter is 56mm. On the optimization, the outer diameter of the impeller is maintained constant to restrict the pump size, and an objective function of pressure head is maximized with eight design variables, which are related with designing an impeller shape. The response surface method is used to the optimization scheme, and the commercial code CFX-10 is applied for numerical analysis. The pressure head of the objective function obtained with an optimized impeller is increased by 9.7% compared with that obtained on an impeller designed with typically recommended design parameters. This increment is caused by reducing the recirculation region within the impeller passage.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.4
• /
• pp.70-75
• /
• 2006

The performance of a turbopump system composed of an inducer, an impeller, a volute and seals has been computationally analyzed. To save the computational time, only one flow passage of the inducer and impeller is considered for the computations. A steady mixing-plane method is used on the impeller/volute interface for simulating the unsteady interaction phenomena. The axial thrust is predicted from the turbopump calculation in its entirety, which is necessary for such estimation. Moreover, the effects of each component on the pump performance are investigated at a design condition through the analysis of flow structures. The predicted performance is in good agreement with experimental data in terms of head rise, efficiency and volute wall pressure distributions despite of highly complex flow structures being present. The computational results also show that the axial and radial thrusts are within the design limit although corresponding experimental measurements were not taken.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.317-320
• /
• 2011

Hydrogen peroxide turbopump was designed for bi-propellant liquid rocket engine using hydrogen peroxide and kerosene as propellants. Turbopump operation was verified through water tests. Design conditions of hydrogen peroxide turbopump were determined, and impeller was designed. Turbine which drives pump was selected from commercial turbocharger. Gas generator was designed by reference from turbine map. Pump, turbine, gas generator were integrated, and turbopump system was constructed. Turbopump supplied water by 1.47 bar of pressure and as well as 3.4 kg/s of mass flow rate.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.16-25
• /
• 2011

A Turbo-impeller is widely used in industries as well as in aero engines. Its design technology has been developed since the early 20th century. However, the final configuration of the impeller depends on the designers. In this study, a whole design process was introduced and an optimization method to design an impeller was studied in order to design a better impeller without influence by designers. In particular, as the Artificial Neural Network was applied to the optimization, the computational time for the optimization was equivalent to the time consumed by the gradient method and its result was guaranteed as the optimum in the whole design domain. Using this method, any impeller can be improved by selecting design variables after measuring profiles of the impeller.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.531-534
• /
• 2006

This study is concerned with radial turbine design and performance improvement of a turbo generator system, which is used for maximizing performance of a 250kW MCFC fuel cell system. A preliminary design of a radial turbine has been performed under the thermodynamic and fluid-dynamic conditions determined by a cycle analysis of the MCFC BOP system. Basic demensions are determined by a meanline analysis and calculation of radial variation at the exit of the turbine. The turbine impeller is designed and modified by iterative processes of three dimensional flow analysis.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.675-679
• /
• 2004

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.205-210
• /
• 2007

A LOX pump rotordynamic design was performed for a 75 ton thrust liquid rocket engine. Axial positions of an inducer, an impeller and bearings on a shaft are decided on the basis of the experience achieved by previously developed turbopump which has the similar layout. The result of pump hydraulic design was reflected in the present study to decide axial length of the inducer and impeller. A distance from the rear bearing to the impeller was considered as a design parameter for load distribution of the bearings. Asynchronous eigenvalue analysis was performed as a function of rotating speeds and bearing stiffness to investigate critical speed of the LOX pump. From the numerical analysis, it is found that the LOX pump with the proper bearing loads safely operates as a sub-critical rotor of which critical speed is high enough compared to the operating speed 11,000 rpm.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.72-80
• /
• 2004

LOX pump is one of the sub-assemblies constructing turbopump unit. In the current study, static structural analysis on such rotating parts as impeller and inducer has been carried out. Three major factors which can affect the structural stability of the rotating parts of LOX pump, are temperature, pressure, and centrifugal force. The effect of each factor was preliminarily investigated, then the analysis under the consideration of the combined loading conditions has been carried out. The major factor that affects the structural stability was proved to be temperature. The analyses of the combined cases showed that the designed impeller and inducer had reasonable safety margins, which means that the impeller and the inducer will be stable in static structural strength. Although there was no problem in the structural strength of the impeller and the inducer, a model analysis should be followed in order to verify the interference between the rotating part and the inner surface of casing.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.219-225
• /
• 2000

Primary function of a centrifugal compressor volute is to serve the flow from the impeller and diffuser to pipe system. But losses in volutes at off-design lead to poor stage efficiency and reduction of operating range. This is largely caused by the interaction between the impeller and volute flow fields. The magnitude of distortion is increased as the operating point is away from the design point and, as a result, the interaction between the impeller and volute is stronger. The objective of present study is to find the characteristics of tile flow in the diffuser and volute of the centrifugal compressor with rectangular cross-sectional volute. The measurements are carried out in two cases with the existence and nonexistence of the volute casing. The detailed pressure is presented by comparing the experimental results obtained at two cases with each others.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.4
• /
• pp.5-10
• /
• 2010

This study is concerned with effects of impeller blade thickness on performance of a turbo blower. This turbo blower is developed as an air supply system in 250 kW MCFC system. The turbo blower consists of an impeller, two vaneless diffusers, a vaned diffuser and a volute. The three dimensional, steady state numerical analysis is simultaneously conducted for the impeller, diffuser and volute to investigate the performance of total system. To consider the non-uniform condition in volute inlet due to volute tongue, full diffuser passages are included in the calculation. The results of numerical analysis are validated with experimental results of thin blade thickness. Total pressure ratio, efficiency, slip factor and blade loading are compared in two cases. The slip factor is different in two cases and the comparison of two cases shows a good performance in thin blade thickness in all aspects.