• Journal of the Korean Solar Energy Society
• /
• v.33 no.3
• /
• pp.58-66
• /
• 2013

Recently, PV module that the most important part of the photovoltaic system is more widened to lower manufacturing costs for module. However, the broad PV module results to the serious mechanical damage corning from installation circumstances such as snow, wind etc of snow and finally lead to the dramatic degradation of the electrical behavior of PV module. In this paper, 3 kinds of PV modules that consist of the different thickness and area of front glass and the diverse cross sectional structures of the frame are prepared for this experiment. The drooped length and electrical outputs of the PV modules are measured by means of applying 600Pa mechanical load to the PV modules from 1200Pa to 5400Pa base on the mechanical load test procedure of K SC IEG 61215 standard. The simulation data are obtained by the simulation tool as ANSYS and those are validate by comparing with the those experimental results figure out relations between the deformation and the constituent part of PV module.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.3
• /
• pp.23-28
• /
• 2007

In this study, we analyzed the maximum output power characteristics of crystalline silicon photovoltaic module by change of environmental effects. The electrical, optical and thermal property of PV modules were investigated during outdoor test period about 70 days. There was a fluctuation in maximum output power by change in transmittance caused by environment effects like rain, snow and dust. The effects of external environmental change were analyzed using climate data. Also local thermal temperature variation and transmittance imbalance on surface of PV module which might lead degradation of constituent material were detected using infrared camera. The further analysis is describe in the following paper.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.3
• /
• pp.1-6
• /
• 2007

In this study, we analyze the maximum power generation of photovoltaic(PV) module depending on constituent materials and incidence angle dependence of light. To verify characteristics of constituent materials, we made photovoltaic modules with 4 kinds of solar cells and textured glass according to fabrication method. To find the degree of the maximum power generation dependence on intensity of light, Solar Simulator is applied by changing angle of module and light intensity. Through this experiment, to obtain maximum power generation from limited PV modules, it is needed to fully understand constituent materials, fabrication method and dependence of incident light characteristics.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.5
• /
• pp.63-68
• /
• 2010

To guarantee life time more than 20 years for manufacturer without stopping photovoltaic(PV) system, it is really important to test the module in realistic time and condition compared to outside weather. In here, we tested PV modules in highly stressed condition compared to IEC standards. In IEC 61215 and IEC 61646 standards, damp-heat, thermal cycle(TC200) and mechanical test are main test items for evaluating long-term durability of PV module in controlled temperature and humidity condition. So in this paper, we have lengthened the test time for TC200 and damp-heat test and increased the loading stress on surface of module. Through this test, we can get some clue of proper the method for measuring realistic life cycle of PV modules and suggested the minimum time for PV test method. The detail description is specified as the following paper.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.6
• /
• pp.125-130
• /
• 2010

Normally, PV system is designed using local weather condition like lowest and highest temperature and irradiance. But this might give misleading results because it is not realistic data of PV module itself. To give more specific description of PV system, we tested photovoltaic(PV) modules' temperature, irradiance and maximum power generation characteristics from January to December in 2008 for 3kW PV system. From this, we could deeply analyze the accumulation temperature, electrical characteristics of PV module in various condition. So precise approach to PV system design can be done. The detail description is specified as the following paper.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1297-1298
• /
• 2007

염료 감응형 태양전지(DSSC)의 개발 이후 많은 연구와 실험이 상용화를 위한 대면적화에 중점을 두고 진행되고 있다. 대면적화에 대한 대부분의 연구에서 그리드 전극을 넣고 내부적으로 직, 병렬 구조를 조합해 확장 시키는 방법을 채택하고 있지만, 그리드 전극을 넣음으로써 발생하는 손실, 즉 실링 공정의 어려움으로 발생하는 전자의 손실과 제작 공정상에 있어서의 복잡한 절차 및 그에 따라 소요되는 시간 등을 감안할 때 이는 그리 효과적이지 못하다고 할 수 있다. 면적이 작은 여러 셀을 외부에서 연결시켜 대면적화 시켰을 때 그 효과에 대해서 알아보고, 동일한 면적의 대면적화 된 단일 셀과 비교, 그 결과를 분석해 보았다. 그 결과, 우리는 동일한 면적을 가지고 있는 대면적의 단일 셀보다 여러 셀의 병렬 조합으로 이루어진 것이 더 좋은 결과를 나타냄을 알 수 있었다. 이를 바탕으로 유효면적 $8cm^2$을 가지는 셀을 외부적으로 연결시켜 대면적화 시켰을 때 그 효과에 대해서 알아보고 실험하였다. 하나의 모듈을 만들기 위해 직 병렬의 다양한 조합을 시도하여 직렬 연결이 많이 된 모듈일수록 이를 다시 병렬로 연결했을 때 전류의 손실을 많이 줄일 수 있다는 결론을 얻었다.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.69-75
• /
• 2021

In this work, we consider the fabrication method and electrical characteristics of dye-sensitized solar cells (DSSCs), which use titanium (Ti) metal thin films to replace expensive fluorine tin oxide (FTO) electrodes. The thickness of the Ti thin film was changed by adjusting the deposition time of the Ti, and the surface resistance decreased as the thickness of the Ti thin film became thicker. The thickness of the Ti thin film was shown to be similar to the surface resistance of the FTO thin film at approximately 190nm and the DSSC with a thickness of approximately 250nm showed the highest energy conversion efficiency of 4.24%. Furthermore, the possibility of commercialization was confirmed by fabricating and evaluating the DSSC module.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.102-107
• /
• 2012

The purpose of thesis is to improve output of solar cell module by enhancing transmission efficiency. To improve transmission efficiency, transmission interconnection ribbon which is used to connect solar cells and busbar which contacts with it has been improved. To secure reliability, comparison research on output of solar cell modules has been conducted by manufacturing PCB module formed by laminated metal with the same output. The result of this research is based on a output efficiency test of modules by comparing electric conductivity of soldering busbar and laminated PCV type of busbar.

• Journal of the Korea Convergence Society
• /
• v.11 no.4
• /
• pp.157-163
• /
• 2020

This paper is a product design convergence study to improve the aesthetic quality of CIGS solar cells for utilizing urban living structures, identifying problems of existing solar cell panels and drawing expert aesthetic elements for improving CIGS solar cells through survey and [Group discussion of experts] based on aesthetic elements of product design. Out of the aesthetic elements derived, the top three models of the product design process were 'environmental harmonization', 'pattern balance', and 'period universality' to derive the design and assembly design of the CIGS solar cell module for improving aesthetic quality, and applied to apartments, veranda, windows, and streetcar through product simulation. This study is suitable for applying aesthetic and CIGS solar cell function later to actual urban living structure, and future research direction needs to be studied on various patterns and structural design development of design.

• New & Renewable Energy
• /
• v.6 no.1
• /
• pp.38-45
• /
• 2010

Abstract Under the physical stress on photovoltaic (PV) module, it will be warped according to elongation of the front glass and then micro-crack will be occurred in the thermally sealed solar cell. This micro-crack leads to drop of short circuit current of the PV module. This is because of increase of resistance component by micro-crack. Micro-crack at specific solar cell in the module lessens the durability of PV module with reduced output, hot-spot caused by solar cell output mismatch and increased resistance component. This study shows the relation between electrical characteristics and micro- cracks due to mechanical stress on PV module.