• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.201-204
• /
• 2004

In this study, the GSP and in-house numerical codes have been used for analyses of the on-design, static off-design and dynamic off-design performances. Through the various missions including altitude, velocity, and power variations static engine performance have been investigated. The dynamic engine performances based on these complicated variations have been also analysed. Especially, the power, engine rpm and heat overload characteristics of a turbine have been estimated with the response time through the control of a throttle setting rather than a power setting. It could be applied to the FADEC system as an engine control device.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.12
• /
• pp.881-889
• /
• 2019

The pre-swirl system is the device that minimizes energy loss of turbine cooling airflow from the stationary parts into rotating parts. In this paper, an off-design analysis was conducted for the ambient air temperature and turbine load conditions. The discharge coefficient was constant for ambient air temperature and turbine load. However, adiabatic effectiveness was increased. This is due to the volume flow rate. The volume flow rate was increased at higher ambient temperature and higher turbine load. It means that the volume of cooling air was increased and the cooling performance of the air was improved. Consequently, adiabatic effectiveness increased by 30.46% at 100% turbine load compared to 20% turbine load. And increased by 18.42% at 55℃ ambient air temperature compared to -20℃ ambient air temperature.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.219-224
• /
• 2012

In this work, a steady-state performance modeling and off-design performance analysis of the 2-spool separate jet turbofan engine named BR715-56 which is a power plant for the narrow body commercial aircraft is carried out for engine performance behaviors investigation and condition monitoring using a commercial code MATLAB/SIMULINK. Firstly, the engine component maps of fan, high pressure compressor, high pressure turbine and low pressure turbine are generated from similar component maps using the scaling method, and then the off-design performance simulation model is constructed by the mass flow matching and the work matching between components. The model is developed using SIMULINK, which has advantages of easy steady-stare and dynamic modelling and user friendly interface function. It is found that the off-design performance analysis results using the proposed model are well agreed with the performance analysis results by GASTURB at various operating conditions.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1997.10a
• /
• pp.99-104
• /
• 1997

기존의 천연가스 가스터빈 시스템을 IGCC 발전소에 적용함에 있어 야기되는 탈설계점효과를 고려할 수 있는 압축기 성능곡선의 예측방법을 제안하였다. 압축기 성능해석방법으로는 익렬요소방법에 전압력손실, 유동편차각 모델들을 결합하여 사용하였으며, 본 방법에 의한 예측결과와 실제 압축기 성능실험결과를 비교하였다. 예측결과가 다양한 압축기 운전조건에 대해 시험결과와 비교적 잘 일치하였으며, 이를 통해 본 예측방법이 IGCC 공정설계 및 성능평가시 가스터빈 탈설계점 효과를 분석할 수 있는 기본 모듈로 사용될 수 있을 것이다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.17-24
• /
• 2005

In this study, the GSP and in-house numerical codes have been used for analyses of the on-design, static off-design and dynamic off-design performances. Through the various missions including altitude, velocity, and power variations the static engine performance have been investigated. The dynamic engine performances based on these complicated variations have been also analyzed. Especially, the power, engine rpm and heat overload characteristics of the turbine have been estimated with the response time through the control of the throttle setting rather than the power setting. It could be applied to the FADEC system as an engine control device.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.9
• /
• pp.2413-2422
• /
• 1994

The effects of compressor design conditions on the off-design performance of a single-shaft gas turbine engine have been studied. Three different geometric design conditions are considered and three different values for the specific mass flow rate at the inlet to the compressor are assumed. For each of nine compressor design, the off-design performance of the gas turbine engine is predicted using the method previously proposed by present authors. Results show that the predicted off-design performances are quite different from each other even though they have the same performance at design point: it means that compressor design conditions should be determined in consideration of the off-design performance of the engine. The specific mass flow rate at the inlet to the compressor is also shown that it might be optimized with respect to the net power of the engine.

• Journal of Aerospace System Engineering
• /
• v.13 no.1
• /
• pp.38-46
• /
• 2019

There is a growing interest in engine diagnostic technology for gas turbine engines. An engine simulation program, precisely simulating the engine performance, is required in order to apply it to the engine diagnosis technology for engine health monitoring. In particular, the simulation program can predict not only design point performance but also off-design point and partial load performance in accurate. So the engine simulation program for the 2-spool separate flow type turbofan engine was developed and the JT9D-7R4G engine of PW(Pratt & Whitney) was analyzed. The steady-sate performance analysis is conducted at both design and off-design points in flight path and the differences between analysis results of takeoff and cruise conditions are compared. The effect of Reynold's correction method was analyzed as a scaling method of the engine component performance. The simulation results was compared with NPSS.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.281-286
• /
• 2006

본 연구의 목적은 차세대 대체에너지로 각광받는 풍력발전 중에서 육상발전보다 여러 가지 이점이 있는 한국형 해상풍력터빈 블레이드의 최적형상설계를 위한 알고리즘을 구현하는 것이다. 블레이드 단면 익형의 양력과 항력 분포는 XFOIL을 이용하여 예측하였다. 첫 번째 수준의 설계변수인 각각의 블레이드 지름과 축 회전수에서 익형의 공력변수들과 최소에너지손실 조건을 이용하여 두 번째 설계변수인 각 블레이드 단면에서의 시위길이와 피치각 분포를 최적화하였다. 그리고 성능결과를 바탕으로 반응면을 구성하고, 확률적 방법을 이용하여 타당성 있는 설계공간까지 첫 번째 설계변수를 이동시키고 구배최적화 기법을 통해 각각의 제약함수를 만족하면서 목적함수를 죄대로 하는 최적블레이드 형상을 구현하였다. 설계된 최적형상에 대해 탈설계점 해석을 수행하여 성능을 구하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.3
• /
• pp.195-203
• /
• 2019

Since the hypersonic intake is directly related to the overall performance of the engine, it is essential to analyze performance characteristics under various off-design conditions. In this paper, Busemann intake and conical intake with external compression were designed, and numerical simulations were performed at on/off-design conditions. Based on the results, the overall performance characteristics of two types of intake were analyzed in various Mach numbers and angle of attacks. The results showed that performance degradation of Busemann intake with truncation angle of 2 degrees was minimal. Also, the performance of Busemann intake was higher than external compression intake at various Mach numbers, however, the starting characteristics were significantly reduced with an angle of attack.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.47-55
• /
• 1998

Steady-state and transient performance for the medium scale civil aircraft turbofan engine was analyzed. Steady-state performance was analyzed on maximum take-off condition, maximum climb condition, and cruise condition. At 90％RPM of the low pressure compressor, the partload performance was economized. The transient performance was analyzed with cases of the step increase, the ramp increase, the ramp decrease, and the step increase and ramp decrease for the input fuel flow. For the transient performance analysis, work matching between compressor and turbine was needed. Modified Euler method was used the integration of residual torque in work matching equation. At all flight condition, the overshoot of the high pressure turbine inlet temperature was appeared in the step and ramp increase case, and the surge of high pressure compressor was appeared in the step increase case and the ramp increase case within 5.5 seconds of maximum climb condition.