• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.146-154
• /
• 2010

The effects of severe plastic deformation, equal channel angular pressing, and annealing of Al 5052 alloy on elastic modulus have been studied. The AI 5052 alloy was plastically deformed by ECAP method after solution treatment, and then finally annealing heat treated. Elastic modulus was measured by conventional tensile and nano-indentation test, and also measured on the surface of the specimen using acoustic material signature of the acoustic microscope. The variation in the elastic modulus influenced by plastic deformation and heat treatment, inaccessible by the conventional techniques, was successfully measured by acoustic material signature and obtained the elastic modulus depending on crystal orientation at each grain.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.253-256
• /
• 2011

본 논문에서는 표면효과와 비선형 탄성효과를 고려한 FCC 나노박막의 순차적 멀티스케일 해석 모델을 제시한다. 표면에서의 구성방정식은 표면응력과 표면탄성계수를 이용하여 선형으로 표시되며, 표면효과를 나타내기 위한 표면물성들은 EAM 포텐셜을 이용한 원자적 계산 방법으로 계산된다. 두께가 얇은 나노박막은 표면응력으로 인하여 면내 방향으로 수축 또는 인장의 변형이 발생하게 된다. 나노박막의 평형상태에서의 변형율은 두께가 얇은 박막의 경우 재료가 선형 탄성 영역을 벗어나는 값을 가지는 경우가 많으므로 나노박막의 해석시 벌크 영역의 비선형 탄성 효과를 고려해야 한다. 이러한 비선형 탄성 효과를 고려하기 위해 본 연구에서는 FCC 구조를 가지는 금속의 비선형 탄성 모델을 제시하고, EAM 포텐셜로 계산된 응력과 탄성 계수를 이용하여 매칭 기법을 통하여 비선형 탄성 모델의 계수들을 결정한다. 또한 Cauchy-Born Rule 모델과 분자동역학 전산모사를 통하여 본 연구에서 제안된 비선형 탄성 모델에 대한 검증을 수행한다.

• The Journal of Engineering Geology
• /
• v.16 no.1 s.47
• /
• pp.1-14
• /
• 2006

Various measurements were carried out to estimate the modulus of deformation in two dominant rock types in Korea: granite and gneiss. Four most commonly used methods were utilized: Goodman jack tests, PS well logging, laboratory ultrasonic tests and laboratory uniaxial loading tests. Laboratory static and dynamic Young's moduli depend on the magnitude of the applied axial stress, range of Sequency used for measurement and the loading/unloading condition. As the laboratory measurement condition approaches to that in situ, the resultant moduli also appear to be comparable to that in situ. This suggests that the simulation of in situ stress condition is important when the modulus of rock is determined in the laboratory Dynamic Young's modulus is generally higher than static Young's modulus because of (micro)crack behavior in response to the stress, different range of frequency used for measurements, and the effect of the amplitude of deformation. Understanding of the relations in moduli from different measurement methods will help estimate appropriate in situ values.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.48-55
• /
• 2009

In the glulam beam deflection it is necessary to check the reliability of theory formula, because of wood anisotropy and wood qualities (knot, slop of grain). In this experiment, when bending stress occurred on glulam, practice deflection of glulam measuring with AICON DPA-Pro 3D system were compared with prediction deflection calculated as substituting MOE through non-destructive testing and static MOE through bending test in differential equation of deflection curve. MOE using ultrasonic wave tester of laminae, MOE using natural frequencies of longitudinal vibrations ($E_{cu}$, $E_{cf}$), MOE using ultrasonic wave tester of glulam ($E_{gu}$) and MOE using natural frequencies of longitudinal vibrations ($E_{gf}$) were substituted in this experiment. When practice deflection measured by 3D system was compared with prediction deflection calculated with differential equation of deflection curve, within proportional limit the ratio of practice deflection and prediction deflection was similar as 1.12 and 1.14, respectively. Deflection using ultrasonic wave tester was 0.89 and 0.95, Deflection using natural frequencies of longitudinal vibrations was 1.07 and 1.10. The results showed that prediction deflection calculated by substituting using non-destructive MOE of glulam having anisotropy in differential equation of deflection curve was agreed well with practice deflection.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.3
• /
• pp.63-72
• /
• 2015

This paper describes the correlation and relationship between elastic moduli measured by three stiffness measurement methods with different mechanical characteristics to evaluate the compaction characteristics of subgrade soils. The Soil Stiffness Gauge (SSG) with very small strain (${\approx}0.001%$) ranges, static Plate Loading Test (PLT) with mid-level strain (${\approx}0.01{\sim}0.1%$) ranges, and Dynamic Cone Penetrometer (DCP) using penetration resistance were implemented to measure the elastic modulus. To use the elastic modulus measured by different measurement methods with a wide range of strain in practice, it is required to identify the correlation and relationship of measured values in advance. The comparison results of the measured elastic moduli ($E_{SSG}$, $E_{PLT}$, $E_{DCP}$) using the three measurement methods for domestic and overseas subgrade soils under various conditions indicate that the evaluated elastic modulus relies on the types of soils and the level of stress condition. The correlation analysis of the measured elastic moduli except the data of cement treated soils indicates that the static elastic modulus ($E_{PLT}$) is evaluated as about 60 to 80% of the dynamic elastic modulus ($E_{SSG}$). Unusual soils such as cement treated soils are required to be corrected by the stress correction during the correlation analysis with typical soils, because these types of soils are sensitive to the stress condition when measuring the static elastic modulus ($E_{PLT}$) of soils. In addition, when considering the use of DCP data for the evaluation of the elastic modulus ($E_{DCP}$), the measured data of the elastic modulus less than 200 MPa show more reliable correlation.

• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.67-75
• /
• 2002

For the design of concrete structures in the serviceability limit state, the uniaxial static modulus of elasticity may be a most important parameter. In particular, this may be so just for a deflection control of the structure. Even in new concrete codes, however, the elastic modulus is normally presented on the form of general empirical relationships with the compressive strength and density of concrete. Normally, there is a large uncertainty associated with the general equations obtained by regression. Thus, in a typical plot of static modulus of elasticity vs. compressive strength, a large scatter can be observed at same strength. The aim of this study is to present the method for obtain the maximum modulus of elasticity at same compressive strength. In the present paper report the effects of mix ingredients on the modulus of elasticity of high-strength concrete. The test of 284 cylinder specimens arc conducted for type I with 11 ％ replacement of fly-ash cement concretes. Different water-hinder ratio, amounts of water and coarse aggregate as variables were investigated. And also analyzed it statistically by using SAS.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.71-77
• /
• 2010

Anti-freezing layer does not used in case of non frost heaving in subgrade soils. In this case, the modulus of subgrade soils were varied with freezing and thaw cycles under non frost heaving. That effect should be properly considered in pavement design. Impact resonance test that is nondestructive testing method was used for continuously determining the modulus of subgrade soils during freezing and thaw cycle. The modulus of subgrade soils was identical with freezing and thaw cycles under closed freezing and thaw system which is no water supplement into specimen during testing. There was also no difference in the modulus of subgrade soil between before and after freezing-thaw cycles for all specimens with different water content and density. That is thaw-weakening of subgrade soils do not occur under closed freezing and thaw system. The moduli at freezing conditions are varied with water content and density, but it can be ignored in practical design sense.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.11a
• /
• pp.110-115
• /
• 1991

일반적으로 거의 모든 재료의 기계적인 물성치들이 여러가지 하중조건에 의해 변화하는데 그 중 탄성계수는 하중속도, 온도, 재료의 특성에 따라 변화한다. 지금까지 국내에서의 연구동향을 보면 하중속도가 탄성계수에 미치는 영향에 대한 연구보고는 미약한 실정이다.(중략)

• Journal of Korea Foresty Energy
• /
• v.22 no.1
• /
• pp.44-48
• /
• 2003

Flexural properties were investigated on clear specimens made from small diameter thinned trees of pitch pine (Pinus rigida Mill.), Japanese red pine (Pinus densiflora Sieb. et Zucc), Japanese larch (Larix kaempferi Carr.), and sawtooth oak (Quercus acutissima Carr.). MOR and MOE values of small clear specimen were depended on the species. The highest density of sawtooth oak shows the highest values of MOR and MOE. However, the lowest density of Japanese larch shows the lowest values of MOR. It was also shown that flexural properties could be predicted by stress wave MOE, since the correlations between stress wave MOE and flexural properties were relatively good.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.4
• /
• pp.47-55
• /
• 2007

Using the results of the Piezocone Penetration Test (PCPT) which were executed at the Yangsan-Mulgum site, the applicability of the interpretation methods for estimating the coefficient of consolidation ($C_v$) of soft clay was evaluated. At the same time, laboratory soil tests using the total of 172 undisturbed soft clay samples from the 44 regions of the Yangsan-Mulgum site were performed to study the differency in the coefficient of consolidation ($C_v$) compared to the results of PCPT. The calculated constrained modulus ($M_{\varepsilon}$) and coefficient of consolidation ($C_v$) using the results of consolidation laboratory tests which are based upon the consolidation theory of Terzaghi were compared with the predicted constrained modulus ($M_p$) and coefficient of consolidation ($C_{v-{M_p}}$) from the PCPT. The relationship between the predicted constrained modulus ($M_p$) and the calculated constrained modulus($M_c$) were showed good correlation. The $M_p$ by the Jones & Rust method were showed mostly similar to the calculated constrained modulus ($M_c$). The relationship between the coefficient of consolidation ($C_v$) obtained from the consolidation tests and the calculated coefficient of consolidation ($C_{v-{M_p}}$) were showed a linear relationship. The results of the calculated coefficient of consolidation ($C_{v-{M_p}}$) were about 54% of the value of the coefficient of consolidation ($C_v$) obtained from the consolidation tests.