• 대한기계학회논문집A
• /
• 제37권6호
• /
• pp.731-738
• /
• 2013

본 논문은 6 륜 독립구동/독립조향 차량의 독립 스티어-바이-와이어 장치의 고장 안전 주행 제어방법을 제시하였다. 조향부 고장 휠의 횡방향 타이어 힘이 차량 선회 운동에 저항력으로 작용할 수 있으므로, 이를 줄이기 위하여 본 고장 안전 주행 제어 알고리즘은 조향부 고장 휠에 높은 슬립률이 발생하도록 토크 입력을 가한다. 고슬립으로 인한 조향부 고장 휠의 종방향 타이어 힘 증가를 고려하기 위하여 종방향 타이어 힘을 추정하여 고장나지 않은 휠의 구동력 최적 분배에 구속 조건에 포함시킨다. 개루프 조향 및 폐루프 조향 시뮬레이션 결과 조향부 고장이 발생한 차량의 주행시 고장을 고려하지 않은 최적 구동력 분배 제어에 비하여 본 알고리즘 적용시 차량의 주행 성능이 보정됨을 확인하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2017년도 춘계학술대회
• /
• pp.252-254
• /
• 2017

자동차 타이어는 차량을 운행하는데 있어 중요한 요소 중 하나이다. 타이어가 마모됨에 따라 자동차 제동거리가 늘어나고 슬립현상이 발생할 가능성이 크다. 따라서 주기적으로 타이어의 마모도를 확인하고 교체해주어야 한다. 기존에는 사람이 직접 마모도를 확인하여 타이어 교체여부를 판단하였다. 하지만 사람에 따라 기준이 다르기 때문에 교체 주기가 불분명해진다. 본 논문에서는 모터 회전각도를 활용한 타이어 마모도 확인 기법을 통해 명확한 교체주기를 마련한다. 명확한 교체주기가 정립됨으로써 타이어로 인한 차량 사고율이 줄어들 것으로 기대되기 때문에 모터 회전 각도를 활용한 타이어 마모도 확인 기법을 제안한다.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.89-94
• /
• 2006

The tire delivering power generated from engine to the ground pulls a vehicle to move. Radius of tires is changeable due to elasticity that depends on the speed of vehicle and traction force. The main objectives on this study are real time measurement of dynamic radius and slip ratio according to the speed and traction force. The dynamic radius is proportional to speed and traction force. According to measurement, the dynamic radius is increased about 3mm under 100km/h compared to stop. It is also increased about 1.5mm when a traction force is supplied as much as 4kN compared to no load state at low speed. There is no strong relationship between slip ratio and vehicle speed. The slip ratio is measured up to 4% under WOT at first stage gear. Through this research, the method of measuring dynamic radius and slip ratio is set up and is expected to be applied to the measurement of traction force in chassis dynamometer or accelerating and climbing ability.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.353-356
• /
• 2002

In vehicle accidents, the rolling, pitching, and yawing which are produced by collisions affect the motions of vehicle. Therefore, vehicle behavior under impact situation should be analyzed in three-dimension. In this study, three-dimensional vehicle dynamic equations based on impulse-momentum conservation principles under vehicle impact are introduced for simulation. This analysis has been performed by the real vehicle impact data from JARI and RICSAC. This study suggested each system modeling such as suspension, steering, brake and tire as well as the appropriate vehicle behavior simulation model with respect to pre and post impact.

• 한국ITS학회 논문지
• /
• 제13권1호
• /
• pp.99-108
• /
• 2014

최근 들어, 차량 제어 기술의 집약체라 할 수 있는 자율 주행 차량에 관한 관심이 증대되고 있다. 특히, 자율 주행 차량의 안정적인 주행과 직결되는 자기 위치 인식 기술에 관한 연구가 꾸준히 진행되어져 왔으며, GPS가 갖는 한계점을 보완하기 위한 다양한 추측항법 기술이 소개되어져왔다. 하지만 기존의 추측항법들은 추가적으로 센서를 장착해야하는 단점과 차량 거동의 급격한 변화로 인하여 자기 위치 인식 정확도가 떨어진다는 단점을 가진다. 따라서 본 논문에서는 기존의 추측항법의 단점을 보완하기 위하여 대부분의 차량에 장착되어 있는 휠속 센서(Wheel Speed Sensor)를 활용하고, 휠속 센서에서 계측된 값을 토대로 타이어 슬립율(Slip ratio)을 추정하여 차량의 급격한 거동 변화에 대응하기 위한 새로운 개념의 슬립율 기반의 추측항법 알고리즘을 개발하였다. 기존의 추측항법 알고리즘과의 성능을 비교 평가하기 위해서 차량의 거동이 급격하게 변화하는 상황이 포함된 시뮬레이션 환경을 구성하여 그 결과를 비교하였다.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.174-180
• /
• 2006

The wheel slip control systems are able to control the braking force more accurately and can be adapted to different vehicles more easily than conventional braking control systems. In order to achieve the superior braking performance through the wheel slip control, real-time information such as the tire braking force at each wheel is required. In addition, the optimal target slip values need to be determined depending on the braking objectives such as minimum braking distance, stability enhancement, etc. In this paper, a wheel slip control system is developed for maintaining the vehicle stability based on the braking monitor, wheel slip controller and optimal target slip assignment algorithm. The braking monitor estimates the tire braking force, lateral tire force and brake disk-pad friction coefficient utilizing the extended Kalman filter. The wheel slip controller is designed based on the sliding mode control method. The target slip assignment algorithm is proposed to maintain the vehicle stability based on the direct yaw moment controller and fuzzy logic. The performance of the proposed wheel slip control system is verified in simulations and demonstrates the effectiveness of the wheel slip control in various road conditions.

• 한국자동차공학회논문집
• /
• 제20권6호
• /
• pp.126-131
• /
• 2012

Tire force is one of important parameters which determine vehicle dynamics. However, it is hard to measure tire force directly through sensors. Not only the sensor is expensive but also installation of sensors on harsh environments is difficult. Therefore, estimation algorithms based on vehicle dynamic models are introduced to estimate the tire forces indirectly. In this paper, an estimation system for estimating lateral force and states is suggested. The state-space equation is constructed based on the 3-DOF bicycle model. Extended Kalman Filter, Unscented Kalman Filter and Ensemble Kalman Filter are used for estimating states on the nonlinear system. Performance of each algorithm is evaluated in terms of RMSE (Root Mean Square Error) and maximum error.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.517-523
• /
• 2004

Recently, wheel slip controllers with controlling the wheel slip directly has been studied using the brake-by-wire actuator. The wheel slip controller is able to control the braking force more accurately and can be adapted to various different vehicles more easily than the conventional ABS systems. The wheel slip controller requires the information about the tire braking force and road condition in order to achieve the control performance. In this paper, the tire braking forces are estimated considering the variation of the friction between brake pad and disk due to aging of the brake, moisture on the contact area or heating. In addition, the road friction coefficient is estimated without using tire models. The estimated performance of tire braking forces and the road friction coefficient is evaluated in simulations.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.145-153
• /
• 2000

This paper discusses the dynamic modeling and robust control development for a differentially steered mobile robot subject to wheel slip according to high load. Consideration of wheel slip is crucial for high load applications such as construction automation tasks because wheel slip acts as a severe disturbance to the system. It is shown that the uncertainty terms due to the wheel slip satisfy the matching condition for the sliding mode control design. From the full dynamic model of the mobile robot, a reduced ideal model is extracted to facilitate the control design. The sliding mode control method ensures the dynamic tracking performance for such a mobile robot. Numerical simulation shows the promise of the developed algorithm.

• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.78-85
• /
• 2013

This paper presents the sliding mode control methods for anti-lock brake system (ABS) with the friction force observer. Using a simplified quarter car model, the sliding mode controller for ABS is designed to track the desired wheel slip ratio. Here, new method to find the desired wheel slip ratio which produces the maximum friction force between road and tire is suggested. The desired wheel slip ratio is varying according road and tire conditions to produce maximum friction force. In order to find optimum desired wheel slip ratio, the sliding mode observer for friction force is used. The proposed sliding mode controller with observer is evaluated in simulation, and the control design is shown to have high performance on roads with constant and varying adhesion coefficients.