• Journal of the Society of Disaster Information
• /
• v.14 no.1
• /
• pp.79-88
• /
• 2018

In this study, the changes of the expansion and strength according to the temperature of the emergency repairing expansion material were examined by cup foaming test and uniaxial compressive strength test, and the accelerated compression creep test was carried out to confirm the long term stability. Ramp & Hold test and accelerated compressive creep test were performed to evaluate the creep performance. The short - term creep test was used to determine the initial creep strain of the expanding material. The isothermal method using time - To evaluate the long - term compressive creep performance.

• The Journal of Engineering Geology
• /
• v.19 no.2
• /
• pp.165-175
• /
• 2009

This study is concerned with creep characteristics of red shale in the Haman Formation by the single stage and multi stage loading tests. Creep constants in the Griggs's experiential equation, ${\epsilon}_t$= a+$b{\cdot}log$ t + $c{\cdot}t$, are determined by regression analysis on the total data obtained. The transition time between the primary and second creep means the time when the differential value of $b{\cdot}log$ t is equal to the differential value of $c{\cdot}t$. The correlation equation between loads (${\sigma}$%) and creep constants is deduced from the three times multi stage loading tests. Also a failure time under each loads is anticipated from creep constants and maximum strain at the failure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.2
• /
• pp.195-204
• /
• 2004

A series of constant creep and repeated creep tests are performed to investigate the behavior of visco-elasto-plastic materials of chemical grouted sands. In the result of constant creep test, the material exhibits three types of shear strain : elastic, plastic, viscoelastic. The elastic, plastic and viscoelastic strains are linear, i.e., the strains are proportional to the stresses for loading. Good agreement is found between the predicted viscoelastic and test results by the power law and the generalized model. In the repeated creep test, the instantaneous recoverable strain is time-independent and the magnitude of accumulated plastic strain increases with number of cycles. Also it is seen that the accumulated plastic strains are approximately proportional to stress. There are no significant differences between test results predicted values for first cycle, and the differences increase relatively insignificantly with number of cycles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.8
• /
• pp.103-111
• /
• 2002

Steady-state creep analysis of power generation turbine blade is carried out considering thermal loads and centrifugal forces. Creep strains and stresses of the turbine blade are calculated for 3-D finite clement model of the turbine blade. From the numerical results, creep life of the turbine blade is predicted. The results of creep analysis during about 200 hours indicate that creep strains of the turbine blade do not reach the rupture strain of GTD111. Creep stresses of the turbine blade are relaxed as time increases. Maximum creep strain occurs at the tip section of the airfoil pressure surface. The maximum creep strain of the turbine blade is expected close to the rupture strain after 50,000 hours approximately. The turbine blade may not have creep damage for the starting procedure of the turbine.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.4
• /
• pp.321-331
• /
• 2011

The present work is aimed to analyze the creep characteristics of a turbojet engine turbine blade using the theta projection method. The theta projection method has been widely used due to its advantages and flexibility. For the creep characteristic analysis of the turbine blade, tests are performed considering the operating conditions and the non-linear material properties. Results from the creep test are fitted using the four theta model. The predicted proprieties using the four theta model are compared with the prediction model and creep test results. To obtain an optimum value of the four theta parameters in non-linear square method, a number of computing processes in the non-linear least square method were carried out to obtain full creep curves. Results using the theta model has more than 0.95 value of $R^2$. The results between the experimental values and predicted four theta model has about 90.0% accuracy. The theta projection method can be utilized for a design purpose to predict the creep behavior.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.5
• /
• pp.75-83
• /
• 2023

As part of a study to analyze the excessive camber occurring in prestressed concrete railway bridges, this paper presents a calculation method and analysis results for the creep coefficient which defines the increase in camber of a concrete structure over time. Using the creep coefficient formula of the design code, the coefficient is obtained by applying the climatic conditions (relative humidity and temperature) of 12 regions in Korea. The effects of differences in climatic conditions by region and starting time of load on the creep coefficient are analyzed. In order to properly calculate the creep, most of which occurs in the early stages of loading, a detailed analysis is performed by applying a time step analysis method to consider varying climate conditions through loaded period. The creep coefficient obtained by applying the average climate conditions of the region is similar to the average of the creep coefficients obtained by time step analysis. Through time step analysis, it is shown that the offset and overlap effects of relative humidity and temperature on the creep coefficient and the climate effect at the time of initial loading can be appropriately represented.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.3
• /
• pp.409-413
• /
• 2006

The accumulated deformation due to the undrained creep causes the general stability problem for the overall soil mass. In this study, the time-dependent constitutive equation, into which a damage law, modified cam clay model, and Perzyna's generalized viscous theory were incorporated, was derived microscopically. The model prediction agreed well with the experimental result including the case of the undrained creep rupture.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.337-338
• /
• 2010

In this study, the test results on creep properties of high strength concrete are shown compared with various prediction equations about creep. So in order to investigate the creep properties of high strength concrete, the application possibility of prediction equations about creep is studied compared with the equations in ACI-209 and CEB/FIP-90 for concrete produced using Portland cement.

• Geotechnical Engineering
• /
• v.9 no.4
• /
• pp.93-102
• /
• 1993

Soil structures which are constructed over the soft ground settle continuously by the self-weight of embankment for a long time. It is because of timetependent behaviours . consolidation and creep occurring simultaneously. This paper tries to determine the required parameters for analysis of the creep behaviour in marine clays and studied the effect of the confining stress and stress level on the creep parameters . As a result, it presents an equation for the determination of creep parameters according to stress level considering that elastic modulus El and creep parameter f are found to be affected by the applied stress level.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.415-422
• /
• 2001

The present paper focuses on the development of a realistic analysis model for the deformation calculation of reinforced concrete beams subjected to fatigue loadings. The proposed model considers the effect of cyclic creep, which arises from the repeated loading, to calculate the deformation of reinforced concrete beams. A comprehensive experimental program has been set up to identify the deformation accumulation of reinforced concrete beams under repeated loadings. The major test variables were the concrete compressive strength and the magnitude of fatigue loads. The model was calibrated from the present test results. The proposed model allows more realistic analysis of reinforced concrete beams under fatigue loads, especially deformation accumulation of such beams.