• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.220.2-220.2
• /
• 2014

플라즈마 질화 기술은 기존의 침탄 혹은 고주파 표면 경화 기술 대비 낮은 온도에서 열처리 공정이 진행됨에 따라 열 변형을 최소화 시킬 수 있으며, 후 가공을 간소화 시킬 수 있다는 장점으로 인해 자동차 부품 및 기타 응용 산업 분야에 있어 큰 관심을 받고 있다. 그러나 공정 진행에 장시간이 소요되고 복잡한 형상 및 홀 가공에 의한 기능부, 특히 내경부에 대한 균일 질화 처리가 어려워 실제 응용분야 확장에 큰 제약이 따르고 있다. 이를 해결하기 위해 본 연구에서는 일반 글로우 방전 대비 플라즈마 밀도가 10배 이상 높은 공공 음극 방전(Hollow Cathode Discharge, 이하 HCD) 현상을 이용하여 고속 고균일 질화공정을 개발하고자 하였으며, 상용화 적용을 위한 연구를 함께 진행하였다. 사용된 시료로는 실제 자동차 부품으로 사용되는 SCM415 소재의 ring gear와 slip yoke pipe를 사용하였으며, HCD 형성을 위해 특화된 플라즈마 질화장비를 활용, 공정 압력 및 인가 전력 등을 변수로 실험을 진행 하였다. 그 결과 질화 처리 속도에 있어 기존 글로우 방전 플라즈마 질화 대비 1/4 이하 수준으로 그 소요 시간을 단축시킬 수 있었으며, 다량 장입된 시료의 내경 기능부에 있어서도 높은 균일도를 갖는 질화표면이 형성됨을 확인할 수 있었다. 또한 기능부 표면에 형성된 HCD 현상을 열원으로 사용함으로써 외부가열 장치를 사용하지 않으면서도 기존의 hot wall 방식보다 높은 질화 균일도 구현이 가능하였으며, 소요 자원 및 전력 사용 측면에 있어서도 공정 시간 단축 및 외부 가열 공정 제거에 의한 높은 수준의 에너지 절약이 가능하였다.

• Journal of the Korean Professional Engineers Association
• /
• v.20 no.4
• /
• pp.5-11
• /
• 1987

The experiment was carried out for the purpose of studying the carburization of pure iron ingot and sintered iron powder by solid carbon in the atmosphere of $N_2$ gas. The velocity of carburization was estimated by the diffusion coefficient D calculated by carburization equation. The results obtained were as follows ; 1. The briqueted sample of iron fine powder which made by higher pressure, carburization depth and carbon concentration were increased as much, and pure iron shelved the maximum value. 2, The higher the carburization temperature, carburization depth and carbon concentration were increased, and the melting zone which had 3.0~3.3%C at the interface of carburization was formed at 130$0^{\circ}C$. As the pure iron ingot was carburized, the diffusion coefficient D of carbon were 0.211$\times$$10^{-6}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 120$0^{\circ}C$ and 0.391$\times$$10^{-6}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 130$0^{\circ}C$, respectively. 4. As the sintered iron powder was carburized at the pressure of 4 ton/$\textrm{cm}^2$, the diffusion coefficient of carbon were 0.157$\times$$10^{-6}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 120$0^{\circ}C$ and 0.103$\times$$10^{-5}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 130$0^{\circ}C$, respectively.

• Journal of Powder Materials
• /
• v.24 no.1
• /
• pp.29-33
• /
• 2017

Titanium carbide (TiC) powders are successfully synthesized by carburization of titanium hydride ($TiH_2$) powders. The $TiH_2$ powders with size lower than $45{\mu}m$ (-325 Mesh) are optimally produced by the hydrogenation process, and are mixed with graphite powder by ball milling. The mixtures are then heat-treated in an Ar atmosphere at $800-1200^{\circ}C$ for carburization to occur. It has been experimentally and thermodynamically determined that the de-hydrogenation, "$TiH_2=Ti+H_2$", and carburization, "Ti + C = TiC", occur simultaneously over the reaction temperature range. The unreacted graphite content (free carbon) in each product is precisely measured by acid dissolution and by the filtering method, and it is possible to conclude that the maximal carbon stoichiometry of $TiC_{0.94}$ is accomplished at $1200^{\circ}C$.

• Journal of Surface Science and Engineering
• /
• v.41 no.2
• /
• pp.63-68
• /
• 2008

Traditionally and generally used calcined clay was carburized, and its characteristics were studied. Carburization treatment was performed by the thermally decomposed carbon and the deposit carbon which occur in a so called 'Boudouard reaction $(2CO{\rightarrow}CO_2+C)'$ at fuel combustion process in a closed-type furnace. The color of the carburized calcine clay changed from yellow to black, and the carbon component revealed as crystalline graphite by the X-ray diffraction test. The weight of the carburized calcine clay decreased to about 4 wt.% by the 1st heating to $1400^{\circ}C$ in air but it does not decreased by the 2nd heating of the same conditions. By the carburization treatment, the water absorption changed from 13 wt.% to 6 wt.%, and the contact angle for water drop changed, too, from 0 to $87^{\circ}$ which was tested by the photograph of one minute after a water drop contact. It means the carburized calcine clay does not absorb water drop so it has a hydrophobic characteristic.

• Journal of Surface Science and Engineering
• /
• v.45 no.6
• /
• pp.226-231
• /
• 2012

Characteristics of carburized surface layers in 0.18C-3.5Ni-1.5Cr-0.2Mo steels for main shaft bearings of wind turbines have been analyzed and evaluated before and after rolling contact fatigue tests. Mixed microstructure consisting of retained austenite and tempered martensite has been formed with compressive residual stresses in the surface hardened layers of the specimens showing uniform hardness distribution with value about Hv700 after vacuum carburizing and tempering. It has been found on the raceway of the layers of the specimens after rolling contact fatigue tests that the amount of retained austenite decreased and compressive residual stresses increased, resulting from cyclic contact stresses applied during the tests. It has been also revealed that higher durability of the bearings can be obtained through controlling the amount of the retained austenite in the surface of the bearing steels to be lower in this study.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.2
• /
• pp.27-32
• /
• 1989

The effect of quenchant temperature on the surface residual stress was studied for AISI 8620 steel. Specimens were carburized at $900^{\circ}C$ in all case type furnace using a gas-base atmosphere of methanol cracked and liquefied petroleum gas, and then subjected to single reheat quenchant in oil or salt bath in the temperature range of $60^{\circ}C$ to $300^{\circ}C$. After carburizing and reheat Quenching, residual stress was measured by the hole drilling method. Experimental results showed that the surface residual stress was increased as the quenchant temperature was raised. This is in contrast to the fact that the formation of phase of low transformation strain such as bainite results in lower surface compressive stress. The greater compressive stress observed in specimens Quenched at higher temperature may be attributed to the shifting of the transformation start point farther from the surface, as was reported in other carburizing steels.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.84-89
• /
• 2011

This paper studied the carburizing of chromium molybdenum steel which the heat treatment effect of gear geometric tolerance, OPD, Runout, the surface hardness, the maximum hardness, the core hardness and the bending fatigue strength were investigated. Firstly, the deformation is observed, and the results of circularity, squareness, OPD and Runout of SCM822, SCM425, and SCM415 are obtained in order. Secondly, in order to investigate the gear hardness, the surface hardness, the maximum hardness and the core hardness of SCM822, SCM425, and SCM415 are obtained; and the surface hardness of SCM822 is about 10% higher than SCM415's, and about 3% higher than SCM425's. Thirdly, the fatigue strength of SCM822 is about 10% higher than SCM415's, and about 7% higher than SCM425's in the fatigue test results. At last, for the purpose of the minimum deformation of heat treatment, and also the improvement of fatigue strength, the best gear material is SCM822 in this test.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.41.1-41.1
• /
• 2009

최근 금형은 자동차뿐만 아니라 여러 산업에서 필수적이며 제품의 품질은 물론 제조원가에 막대한 영향을 미친다. 이러한 금형은 침탄, 질화, 고주파담금질등에 의해 표면처리 되어져 왔으나, 이와 같이 기존의 처리 방법은 모두 처리물 전체를 가열하거나 균일한 가열을 하지 못하기 때문에 변형의 문제와 처리후의 후가공의 경비 문제, 그리고 극히 일부분만 경화가 필요한 부품에는 적용하기 어려운 문제점이 있다. 이러한 문제를 해결할 수 있는 표면처리로서 레이저 표면처리 방법이 대두되고 있으며, 레이저 표면처리는 레이저 빔을 피처리물의 표면에 조사하고 적당한 속도로 이동을 하게 되면 레이저조사부위가 급속하게 가열되고 레이저빔이 통과한 후에는 표면의 열이 내부로 열전도 되어 급속히 자기냉각(Self-quenching)됨으로서 표면에 새로운 기계적 성질을 갖게 하는 표면처리법이다. 이와 같이 레이저를 이용한 표면처리로 기존의 CW Nd:YAG 레이저 열원보다 효율이 좋은 HPDL(High Power Diode Laser)를 이용한 고효율, 고기능 금형 표면처리 후 재료적 물성을 평가하고자 한다. 평가방법은 레이저빔의 조사속도 및 온도변화에 따른 표면처리부, 열영향부 그리고 모재 부분에 대한 경도특성 및 미세조직 변화를 관찰하였다. 또한 조사속도 및 온도변화에 대해 경화깊이를 관찰하였다.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.341-346
• /
• 2002

In order to improve the low wear resistance of Ti-6Al-4V alloy, plasma carburization treatment was newly carried out without consumption of its good specific strength and fatigue life over the temperature. Effect of the plasma carburization was analyzed and compared with the non-treated alloy by microstructural observation, structure characterization and mechanical property test. The plasma treated alloy formed a carburized layer of about 150$\mu\textrm{m}$ in depth from the surface, where a fine and hard particles of TiC and $V_4C_3$ were homogeneously dispersed through the layer. It was also found that an increase of the wear resistance, fatigue life and hardness, due to the hard and fine dispersoids.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.112-116
• /
• 2005

In the present study, the focus is on the analysis of carbothermal reduction of oxide powder prepared from waste WC/Co hardmetal by solid carbon under a stream of argon for the recycling of the WC/Co hard-metal. The oxide powder was prepared by the combination of the oxidation and crushing processes using the waste $WC-8 wt.\%Co$ hardmetal as the raw material. This oxide powder was mixed with carbon black, and then this mixture was carbothermally reduced under a flowing argon atmosphere. The changes in the phase structure and gases discharge of the mixture during carbothermal reduction was analysed using XRD and gas analyzer. The oxide powder prepared from waste $WC-8wt.\%Co$ hardmetal has a mixture of $WO_{3} and CoWO_{4}$. This oxide powder reduced at about $850^{\circ}C$, formed tungsten carbides at about $950^{\circ}C$, and then fully transformed to a mixed state of tungsten carbide (WC) and cobalt at about $1100^{\circ}C$ by solid carbon under a stream of argon. The WC/Co composite powder synthesized at $1000^{\circ}C$ for 6 hours from oxide powder of waste $WC-8wt.\%Co$ hardmetal has an average particle size of $0.3 {\mu}m$.