• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.3
• /
• pp.23-30
• /
• 1985

When a digital filter implementation is based on a difference equation, the frequency characteristics cannot be obtained by direct computation, but be obtained by experiment or analogized by Z-transform. In this paper, the method to compute the frequency magnitude response of the function expressed in a difference equation is derived from PARSEVAL's relation. To verify the validity of this new method two types of digital filters are implemented. Both filters' characteristics are measured and their values are compared with the value obtained by a Z-transform and with the value by a difference equation. The result shows that the measured values and the values obtained by the difference equaton are more closer than the values by a Z-transform. And the difference-equaton-based filters' showed sharper roll off characteristics than the Z-transform-based filters. Therefore when a digital filter implementation is based on a difference equation, the characteristics computation by a difference equation predicts better practical results than based on Z-transform.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.8 s.179
• /
• pp.1931-1939
• /
• 2000

Operating excitation forces of the linear vibratory system are normally determined by direct measurement techniques using load cells, strain gauges, etc. But, hydraulic forces of the rotating turbomachinery such as centrifugal pumps are exerted on an impeller due to asymmety of the flow by the interaction between pump impeller and volute. So, investigations of wide range of hydraulic designs and geometric deviations are difficult by direct method. This paper presents a hybrid approach for fourier transformed operational excitation forces, which uses pseudo-inverse matrix of the transfer matrix for the system and the measured vibrational data with standard installed pump. The determination of the transfer function matrix is based on a linear rotor/stationary system and steady state harmonic response in finite element analysis. And, vibrational data is collected in both vertical and horizontal directions at inboard and outboard bearing housings. The results of the process may be enhanced by making acceleration measurements at many more locations than there are forces to be determined.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.217-222
• /
• 2018

The deterioration of the Battery is decided by SoC and SoH. To determine Battery deterioration, SoC measurement method of Battery by Transfer Function was studied. The SoC of the Battery changes most greatly in the 1Hz band where the DC resistance is detected. but it is a narrow band to observe, therefore, the observation band was moved to 1kHz using the tone busrst signal. Welch's method was used to observe the frequency domain characteristics of the signal. As a result of the spectral estimation, it was confirmed that the response signal of the battery is 1dB difference when the SoC is 40%, 60%, and 80%, respectively. Through this, Proposed the new method of Battery SoC measurement.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.5
• /
• pp.494-510
• /
• 2019

Underwater acoustic communication channel parameters consist of impulse response, delay spreading, scattering function, coherence bandwidth, frequency selective fading, coherence time and time variant magnitude fading statistics on which communication system modem and channel coding are designed. These parameters are influenced by sound velocity profile, platform motion and sea surface roughness in given acoustical oceanography condition. In this paper, channel model based on phasor, channel simulator, measurement and analysis method of channel parameters are given in a fixed source-to-receiver system and the parameters are analyzed using shallow water experimental data. For two different source-to-receiver ranges of 300 m and 600 m, the parameters are characterized by three multipaths such as a direct, a surface reflection path with time variant scattering and a bottom reflection path. The results present a channel modelling method of a fixed source source-to-receiver system, channel parameters measurement and analysis methods and a system design and performance assessment method in shallow water.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.12
• /
• pp.1243-1249
• /
• 2012

Finite element models are updated in two stages in this paper. In the first stage, damping is neglected, and mass and stiffness matrices of a finite element model are updated using an optimization technique. The objective function for optimization consists of natural frequencies and mode shapes obtained from experimental modal testing data and finite element analysis. In the second stage, damping is considered with the mass and stiffness matrices fixed. A damping matrix is estimated assuming a proportional damping system. Then the damping matrix is adjusted using an optimization process so that the difference between the analytical and measured frequency response functions becomes minimum. This procedure of model updating has been applied to a simulated system and an experimental cantilever beam.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.169-173
• /
• 1991

최근 자동화기술의 발달에 따라 산업용 로보트팔의 경량화, 고속화를 실행하 게 되는 경우와 우주, 원자력발전소 등과 같은 특수한 환경하에서 매니퓰레 이터(manipulator)를 제어하게 되는 경우가 많아지고 있는데, 이때 팔의 강성 이 충분하지 않으면 위치결정시 목표점에서의 과도진동이 발생하게 되어 위 치결정정도와 작업효율이 저하된다. 그러므로 이러한 경량화된 장비들의 진 동특성을 파악하고 운동시 발생하는 진동을 효율적으로 제어할 수 있는 제 어기(controller)를 설계하여 잔류진동을 감쇠시키므로써 위치결정시간을 줄 일 수 있고, 전체 작업행정시간이 단축되므로써 작업ㅎ류을 향상시키는 효과 를 가져오게 된다. 이때 원하고자 하는 제어를 하기 위해서는 제어대상 (plant)의 계규명(system identification)을 정확히 하여야 하는데 해석적으로 계를 규명하기가 까다로운 경우 제어기를 설계하는 것이 사실상 어렵게 되 므로 이러한 경우 실험적인 방법으로 주파수응답함수(frequency response function)를 구해 계의 모형(model)을 구하는 방법이 널리 사용되고 있다. 이 분야에 있어서 기존의 논문들은 팔의 변위를 측정하여 진동을 제어하나 이 러한 방법들은 간헐적으로 움직이는 산업장비(예:로보트의 팔)의 과도응답을 제어하기에는 부적합하다. 따라서 본 연구에서는 이러한 장비들의 과도응답 을 효과적으로 제어할 수 있도록 가속도계를 사용, 가속도를 측정하여 변위 를 제어하고자 한다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.85-86
• /
• 2009

A nondestructive test method based on the self-compensating frequency response function is proposed in this paper to quantitatively measure the attenuation in concrete materials. Since the proposed technique measures inherent attenuation of material itself, more stable experimental results can be expected. In advance, comparison of the experimental results to those obtained by other methods shows the repeatability and accuracy of the proposed technique.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.2
• /
• pp.97-102
• /
• 2005

Acoustic experiments were performed with Zostera marina to study the characteristics of backscattering of seagrass living in the bottom interface. Field experiments were conducted in the Dongdae man, Namhae for day and night to consider the effects of air-bubble from photosynthesis of seagrass. The multi-frequency (30$\~$120 kHz) responses were measured and the distributions of back scattering strength due to the movement of seagrass were Presented by PDF (probability density function) at 120 120 kHz. The results were shown both the frequency dependence and diurnal variation of the backscattering strength between day and night. This diurnal variation may be caused by the amount of oxygen in dissolved bubbles formed by Photosynthesis of seagrass.

• Journal of the Korean Society of Radiology
• /
• v.15 no.5
• /
• pp.705-713
• /
• 2021

The modulation transfer function (MTF) is calculated to analyze the resolution of the spatial frequency of the image acquired from the x-ray imaging system. In general, the response function of the detector acquires a line spread function (LSF) using a slit-camera, and derives a modulation transfer function through a Fourier transform. Because of the fact that the x-ray must always be incident on the center of the slit-camera, the tilt of the detector and slit-camera caused by the experimenter will affect the detector performance. In addition, if the tilt increases, the performance evaluation of the x-ray image system will be problematic. In this study, we analyzed the experimental and analytical models in the modulation transfer function, ie, the Fourier domain, based on the experimental error and analyzed the effect on the spatial frequency. Furthermore, performance evaluation is being carried out for various x-ray imaging systems, and experimental errors are indispensable, and the extent to which they can be tolerated should be reviewed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.505-513
• /
• 1996

In this paper the dual-mode bandpass filters with a Chebyshev response are designed and manufactured at Ku-band as well as K-band. Manufactured filters are resonated by two independent orthogonal $TE_{113}$ circular-cavity modes and characterized by 4-pole Chebyshev function. One is operating at a center frequency of 12.5GHz with a bandwidth of 100MHz and the other, a center frequency of 19.25GHz with 120MHz, respectively. The measureed experimental results of a 12.5GHZ dual-mode filter ahve a 1.2dB intertion loss in the passband and 65dB out-of-rejection, and a 19.25GHz filter has a 1.55dB insertion loss and 70dB out-of-rejection. These experimantal results shoults show good agreements with the design specifications.