• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.461-462
• /
• 2008

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.161-162
• /
• 2009

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.591-592
• /
• 2009

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.733-734
• /
• 2008

• 한국공작기계학회논문집
• /
• 제17권6호
• /
• pp.43-48
• /
• 2008

This study includes contents on an effective designing of the outer-wall piece removing equipment of a hull, by applying TRIZ. To remove the piece, gas torch was used. However, the heat source must be shut down since the heat source of gas torch has a bad influence on this system. This is why TRIZ and Brainstorming were used, to solve this problem. First, we analyzed the system using TRIZ, and then presented the direction a solution is expected to follow. And the most suitable scheme was derived from brainstorming which had been conducted based on the direction of a solution. Lastly we conducted an equipment modeling based on the most suitable scheme we made before, and carried out the heat analysis to inspect its effect by comparing pre-existing mechanism with most suited scheme.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.136-143
• /
• 2008

This paper presents the application of a robot which aims at grinding automatically welding-bead remained in the removal job of working pieces for shipbuilding. In specific, the investigation on this application is composed of two parts; one topic is on the development of a robot platform vertically movable on a steel plate of hull, while the other topic is of the development of a grinding tool mechanism in order to remove welding-beads by using a diamond wheel installed on a servo cylinder (which can result in high working pressure on the grinding wheel). Besides, the development of a vision system for tracking welding-beads as well as recognizing welding surfaces is added for the convenience of this robot application to the removal of welding-beads remained in the working pieces for shipbuilding.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.50-56
• /
• 2010

This paper presents a new design algorithm for piece-removing dynamical system, based on 6-Sigma DMADOV technique using ARIZ and Brainstorming. Our design target is the piece-removing system installed on a mobile platform of bead-grinding equipment. The 6-Sigma DMADOV technique guides us design process according to 6 steps, i.e., Define - Measure - Analyze - Design - Optimize - Verify. A Design strategy to reduce the weight of piece-removing dynamical system will be explored by using ARIZ, i.e.,(the abbreviation of Algorithm for Inventive Problem Solving in Russian). The ARIZ will result in a final solution that the height and angle control parts for a cutting tool should be replaced by a kinematical approach, rather than complicated mechatronic approach(using motors). The Optimize step is composed of two sub-steps: (i) Generating process for obtaining several ideas of piece-removing system by using Brainstorming technique, satisfying the final solution derived from the Design step using ARIZ, and (ii) Optimizing process for selecting the most optimal idea of piece-removing system by using Pugh's matrix from the viewpoints of weight, cost and accuracy. The laststep of Verify has shown that the final design obtained by the 6-Sigma DMADOV technique with ARIZ & Brainstormingcan improve an initial design with design requirements satisfied. In this paper, we have shown that ARIZ and Brainstorming can be cooperatively merged into 6-Sigma DMADOV to give us both a formulatedproblem-solving approach and diverse candidate solutions(or ideas) without trial-and-error efforts.