• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.8
• /
• pp.617-625
• /
• 2002

In this study, effects of refrigerant and oil charges on the performance of a refrigeration system simulating an automobile air conditioner have been experimentally investigated using R134a and PAG oil. Measurements were taken in a breadboard type refrigeration test unit with a compressor used for a commercial automobile air-conditioner under a set of condition imposed upon normally to automobile air conditioners. Both the COP and capacity decreased rapidly as the oil charge increased because of the decrease in vapor pressure of the circulating refrigerant/oil mixture. The excess oil left in the evaporator also caused heat transfer degradation resulting in a decrease in capacity and in turn COP. It was found that there is an optimum refrigerant charge at which the COP becomes the maximum. Below this optimum charge, both the capacity and COP increased as the refrigerant charge increased and above the optimum charge, both of them remained almost constant. Hence, the COP seems to be the most important factor in determining the optimum refrigerant charge. When the system was undercharged, the refrigerant at the condenser exit lost subcooling and showed a sign of poor miscibility.

• Korean Journal of Food Science and Technology
• /
• v.11 no.2
• /
• pp.81-85
• /
• 1979

A Neotec infrared instrument was evaluated for determination of protein contents of wheat and barley. Correlation coefficients between protein content determined on the instrument and by the Kjeldahl method were highly significant (0.97 to 0.98). Accuracy of analyses, measured by the standard error of a single test was 0.07 to 0.16, giving a coefficient of variability of 0.6 to 1. 1%. Method of grinding samples affected particle size and type. Particle size did not directly influence protein values; however, greater accuracy and reproducibility were achieved with smaller particle sizes. Packing density inside the loading tell also influenced the analytical results.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.494-502
• /
• 2016

A 1-dimensional heterogeneous reactor model with the gas-solid interfacial phase gradients was developed for the simulation of the packed bed reactor where the exothermic reversible water gas shift reaction for the natural gas steam reformed gas was proceeding in adiabatic mode. Experimental results obtained over the WGS catalyst, C18-HA, were best simulated when the frequency factor of the reaction rate constant was adjusted to a half the value reported over another WGS catalyst, EX-2248, having the same kinds of active components as the C18-HA. For the reactor of the inside diameter 158.4 mm and the bed length 650 mm, the optimum feeding temperature of the reformed gas was simulated to be $194^{\circ}C$, giving the lowest CO content in the product gas by 1.68 mol% on the basis of dried gas. For reactors more extended in the bed length, the possible lowest CO content in the product gas with the optimum feeding temperature of the reformed gas were suggested.

• Journal of the Korean Institute of Gas
• /
• v.17 no.4
• /
• pp.26-32
• /
• 2013

The best way to prevent major occupational accidents is prohibiting use of hazardous substances such as flammable gas, toxic gas whereas using alternative substances that ensured safety. but if there are no economic efficiency and substituting technologies of alternative substances, the best way is preparing to prevent accidents thoroughly. Therefore, this study has developed and selected release scenarios to use and apply for consequence analysis and emergency action plan for HF charging process of chemical plants that have HF release accidents and high probability of release accidents.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.529-538
• /
• 2002

콤바인 곡물 포대 자동화장치개발은 콤바인 운전자 및 작업자의 피로경감과 안전보호 및 작업성능의 향상을 기하기 위하여 행하여 졌으며, 본 연구의 개발은 기존의 콤바인 작업이 2명이 소요되는 것을 운전자 1명이 수확작업을 할 수 있도록 하며, 노동력의 절감과 작업의 편리성을 도모하고자 하였다. 이러한 본 연구의 결과는 다음과 같다. 1) 곡물 포대의 정 위치화를 위해서 용량형 근접위치센서를 설치하였으며, 포대의 과다이송에 따른 모터의 부하를 최소화 하기위해 선단부와 슈트부에 각각 위치센서를 설치하여 포대의 위치를 제어하였다. 2) 곡물 투입장치부의 작동은 공기압축기와 공압실린더를 이용한 공압시스템을 사용하였으며, 곡물의 투입량제어는 슈트부 게이트의 열림시간을 제어하여, 곡물의 투입량을 제어하였다. 3) 포대 배출장치는 이송장치로부터 이송되어진 충진된 포대를 제 2의 포대가 충진하는 영역 밖으로 밸트 컨베이어를 이용 이송하도록 하였다. 4) 포대는 B3 포대의 경우가 가장 투입량이 많은 것으로 나타났으며, 가진을 한 경우가 하지 않은 경우보다 비교적 투입량이 많은 것으로 나타났다. 본 연구에서 개발된 포대 자동화장치에서는 포대의 가진 장치를 장착하지 않았으며, 실험은 인위적으로 가진을 하여 실행하였으며, 향후 전체적인 장치의 성능 향상을 위해서 포대의 가진 장치가 필요한 것으로 나타났다.

• The Korean Journal of Petroleum Geology
• /
• v.2 no.2 s.3
• /
• pp.71-81
• /
• 1994

Alluvial fan delta often extends into deep water, forming steep-faced delta front. Depositional features of modern steep-faced fan-delta slope and prodelta are characterized by slump scar, chute/channel, swale, lobe, splay and debris fall. These features largely originate from sediment failure or sediment-laden underflows (sediment-gravity flows) off river mouth. Sedimentary facies of equivalent ancient systems comprise sheetlike and/or wedged bodies of gravelstone and sandstones, slump-scar and -fill, chute/channel-fills, and sheetlike, lobate and slump mass on steeply-inclined fan-delta foreset and prodelta.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.8-15
• /
• 2011

제습기의 역할은 태양열제습냉방시스템 요소 중에서도 매우 중요하다. 본 논문은 이러한 특성에 맞추어 제작된 장치를 갖고서 제습능력에 영향을 미치는 유량비를 바꾸어 실험한 결과이다. 실험은 크기가 $40m^3$인 항온항습실을 대상으로 이루어졌으며, 향류형 제습기의 수직 높이는 0.4m로 고정되었다. 또한 충진층은 액체흡수제와의 접촉면을 넓게하기 위하여 플라스틱 충진재로 채워져 있으며, 흡수제의 온도는 빠른 변화를 보기 위하여 $15^{\circ}C$로, 농도는 40%로 고정하였다. 액체흡수제의 유량과 습도가 높은 공기의 유량을 각각 3단계로 바꾸어 실험한 결과, 풍량이 높을수록 제습기 효과는 낮아졌으나, 전체적인 제습량에서는 많아졌다. 한편, 제습기에서 액체흡수제 유량이 많을수록 제습되는 수분량이 많아졌으나, 시간의 변화에 따라 제습되는 속도는 현저하게 낮아졌다. 따라서, 향후 실험에서는 유량의 변화 폭을 더욱 확대해서 많은 실험 결과를 확보하고, 이를 모델링화 하여 높은 정확도를 예측할 필요가 있다.

• Journal of Practical Engineering Education
• /
• v.9 no.2
• /
• pp.119-124
• /
• 2017

In injection molding process, the runner system of the mold is a flow path for filling the cavity of the molded part during the advance of the screw by the force of the hydraulic cylinder, which involves the filling and packing process of the molten resin. Thus, the sprue, runner and gate greatly affect the appearance of the molded part, the physical properties of the resin, the dimensional accuracy and the molding cycle etc. Feed systems with incorrect runner and gate designs cause various molding defects, So it is important to maintain the optimum runner balance to prevent these defects. In order to improve the knowledge of practical mold technology, which is applied to the manufacturers of injection molds, a training model of the mold technology process is presented based on the technical guidance on the technical difficulties.

• Journal of the Korean Orthopaedic Association
• /
• v.56 no.5
• /
• pp.445-449
• /
• 2021

Insertional bone cysts of the knee joint mainly appear in the form of small cysts at the bone attachment of the cruciate ligaments, and are usually not associated with symptoms. The authors report a 31-year-old man diagnosed with a huge insertional bone cyst connected to the femoral attachment of the posterior cruciate ligament in the knee joint, who obtained good results after curettage and bone cement filling.

• Tribology and Lubricants
• /
• v.39 no.3
• /
• pp.111-117
• /
• 2023

This paper presents an experimental investigation of the tribological characteristics of PTFE composites filled with nano CuO particles under low sliding speed and load. All the specimens were prepared by sintering. Before sintering, the mixture of PTFE powder and CuO particles were mixed by a high-speed mixer using CuO volume fractions of 0.2 vol. % and 5 vol. %. Each mixture was sintered at 350 ℃ for 30 min on the steel disk. We conducted ball-on-disk sliding test an hour using a steel ball against PTFE composites, including pure PTFE. The load and sliding speed used was 2 N and 0.01 m/s, respectively. Adding nano CuO particles increases the friction coefficient because of the abrasiveness of hard nano CuO particles. The highest coefficient of frictions was obtained from 5 vol. % CuO. Conversely, the lowest wear of the composites was obtained from the 5 vol. % CuO nanocomposite. This study reveals that the addition of nano CuO particles can lower the wear of PTFE, despite an increase in the coefficient of friction. However, the coefficient friction is still moderate compared to other engineering polymers. In addition, the amount of CuO nano particles has to be optimized to reduce friction and wear at the same time.