• 설비공학논문집
• /
• 제29권8호
• /
• pp.437-445
• /
• 2017

Because of improvement of living standards and increased use of ice at home, built-in ice makers are of interest. In this study, refrigeration cycle of a unitary ice maker for residential usage was optimized using R-404A. Optimization was achieved through a search for proper refrigerant charge amount. For the present ice maker producing ice for 24 cups, the optimum charge amount was 200 g. In this configuration, the ice making cycle time was 17 minutes 53 seconds, ice production was 1.27 kg/h and COP was 0.310. After initial start-up, condensation and evaporation temperatures gradually decreased with time. As ice builds in the cup, heat transfer performance of the evaporator decreases, that results in decrease of evaporation and condensation temperatures. Replacement of existing slit nozzles with individual circular hole nozzles improved ice production capacity by 10 percent. Through visualization of ice formation in the ice cup, growth rate of the ice in the cup was relatively uniform.

• 설비공학논문집
• /
• 제14권9호
• /
• pp.725-733
• /
• 2002

In this study, the heat transport limitations of a two-phase closed thermosyphon were investigated. For the test, a two-phase closed thermosyphon ($L_t/: 600 mm,\;L_e:105mm,\;L_a:75mm,\;L_c:420mm,\;D_o:22.2mm,$ container: copper (inner grooved surface), working fluid: PFC ($C_6F_14$) was fabricated with a reservoir that can change the fill charge ratio. The following was imposed as the factors on the heat transport limitations of a two-phase closed thermosyphon. 1) Fill charge ratio of the working fluid. 2) Tilt angle of the longitudinal axis. From tile experimental data, some results were obtained as follows. When the fill charge ratio was relatively small ($\psi$20%), the heat transport limitation occurred about 100W by dry-out limitation. However over 40%, it shelved nearly constant value (500 W) by flooding limitation. The heat transport limitation according to the tilt angle increased smoothly until the tilt angle was $60^{\circ}$,/TEX>, after then decreased slowly.

• 조명전기설비학회논문지
• /
• 제26권10호
• /
• pp.111-117
• /
• 2012

Electric vehicles (EVs) are the most promising alternative substitute to a significant amount of gasoline vehicles for climate friendly transportation. This paper conducted an EV consumer survey through the telephone for 200 residents living in apartments to predict the EV penetration level in the year 2020. The results of EV consumer survey revealed that EV will be penetrated to 10% of the total vehicles in rental apartments and to 23.6% of the total vehicles in apartments for sale(condominium) until 2020. High EV penetration level, however, will lead to an increase of power consumption and over loading of electrical installations. Integrating more electric vehicles, the capacity of transformer related in apartments should be checked to prevent the over loading of the transformer. This paper checked the possibility of over loading at transformer and suggested the load control system as one of the solutions to reduce the over loading of transformers in apartments. Also this paper reviewed other components that should be checked in the designing of EV recharging infrastructure in apartments.

• 조명전기설비학회논문지
• /
• 제22권10호
• /
• pp.34-40
• /
• 2008

본 논문에서는 최근 증가 일로에 있는 자동점멸식 보안등에 대한 안전점검 방안을 제시하였다. 기술적인 측면으로서 보안등주의 하부에 안전점검을 위한 별도의 점검함을 설치하고 점검원이 누설전류, 누전차단기의 정상적인 동작 상태, 절연저항 및 접지저항을 승주하지 않고 측정할 수 있도록 하였으며, 충전부에 대한 직접 접촉의 가능성을 최대한으로 경감함으로써 감전의 위험으로부터 자유로울 수 있도록 설계하였다. 본 연구의 결과물을 실용화함으로써 보안등에 대한 점검을 최대한 안전하고 효율적으로 수행하는데 일조할 수 있을 것으로 기대한다.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2005년도 하계학술대회
• /
• pp.92-96
• /
• 2005

본 연구에서는 현재 지하공간에 설치되어 있는 기존의 피난구 유도등의 문제점을 개선하기 위하여 전력선 통신을 이용한 피난구 유도 제어장치 시스템을 제안하였다. 제안한 피난구 유도 제어장치 시스템은 주제어부, 전력선 통신 원격 제어부, 충전부, 음성발생부, 표시부, 경보알람부, 연기감지부 둥으로 구성된다. 제안한 전력선 통신을 이용한 피난구 유도 제어장치 시스템을 실험을 통하여 전력선 통신의 단점인 잡음을 개선하였으며, 기존의 피난구 유도등이 가지는 단점을 보완하는 것을 확인하였다.

• 조명전기설비학회논문지
• /
• 제12권4호
• /
• pp.100-105
• /
• 1998

본 논문은 고조파와 무효전력을 보상하는 전력용 능동펼터의 성능을 가지는 무정전 전원장치의 제어기볍올 제안 한다. 제안된 시스템은 단지 하나의 전력변환회로만올 가지고 AC/DC 정류기 및 배터리 충전기 그리고 인버터로서 동작할 수 있다. 더욱이 상용전원이 정상일 경우 제안된 시스템은 비선형 부하에 의해 발생된 고조파 및 무효 전 력올 보상하기 위해 전력용 능동필터 모드로 동작한다. 그리고 상용전원이 비정상일 경우는 인버터로 동작하여 배터리에 충전된 전력을 부하로 공급하는 배터리 방전전력 모드로 동작올 한다. 전력용 능동필터 모드에서 보상전류 를 정확히 계산하기 위한 새로운 폐-루프 방식을 제안한다. 마지막으로 제안된 5[kVA]급 시스템의 성능이 시뮬레이션과 실험결과들에 의해 입증된다.

• 조명전기설비학회논문지
• /
• 제22권6호
• /
• pp.127-133
• /
• 2008

본 논문에서는 무정전 전원시스템(UPS : Uninterruptible Power Supply)의 에너지 저장용으로 사용되는 납축전지를 최적의 상태로 유지, 관리하는 배터리관리시스템을 설계, 제작하고, 잔존용량을 추정하는 알고리즘을 제안한다. 제안된 배터리관리시스템은 배터리의 충 방전 전류를 제어하여 과방전 및 과충전으로부터 배터리를 보호하며, 충 방전 시 배터리 잔존용량(SOC)을 예측하여 배터리를 최적 상태로 유지하도록 하는 알고리즘이 적용된다. 또한 충 방전 시험기를 이용한 실험과 UPS에 장착한 후 성능 실험을 통해, 제작된 시스템의 성능 및 제안된 배터리 잔존용량 추정 알고리즘의 타당성을 입증한다.

• 조명전기설비학회논문지
• /
• 제27권9호
• /
• pp.15-22
• /
• 2013

A new LED lamp driving technology with a charge pump instead of a conventional DC-DC converter is proposed. The proposed driving technology is used to control the LED lamp with digital dimming. The power loss in the zener diodes is reduced because the charging process of the capacitors is selectively controlled according to the digital control signal. From the experimental results, when dimming four LED lamps simultaneously, the average driving circuit efficiency of 89% is obtained, regardless of the dimming level. White light with color temperature over a range of 2800~7200K was produced by dimming control of red, green, blue and amber LED lamps with the proposed driving circuit. The characteristics of the driving circuits can be changed depending on the characteristics of the R, G, B, and A LED lamps. The efficiency of the driving circuits up to a maximum 89% can also be obtained depending on the combination of LED lamps. The driving technology with digital dimming control for LED lamps proposed in this paper would be effective for obtaining high efficiency in LED driving circuits and remote control of LED lamps using digital communications.

• 설비공학논문집
• /
• 제17권6호
• /
• pp.552-559
• /
• 2005

This paper describes an experimental study on the inertance pulse tube refrigerator using a small compressor. The purpose of this experimental study is to identify the performance of the inertance pulse tube refrigerator for various operating conditions and to obtain the optimum configuration. The dead volume effect is verified by two experimental apparatuses with different dead volumes between the compressor and the aftercooler. The refrigerator of the smaller dead volume shows better performance. The influence of operating frequency and charging pressure on the performance of the refrigerator is experimentally investigated. Reducing the regenerator mesh size improves the performance of the refrigerator. Finally, the inertance pulse tube refrigerator has maximum cooling capacity at the specific combination of the pulse tube length and the inertance tube length. The loss analysis is used to analyze and predict the optimum condition of the pulse tube refrigerator.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.352-356
• /
• 2006

As a basic study to develop heating panel, the purpose of this study was to know possibility as a floor heating panel. We investigated working conditions and performance of pulsating heat pipe. Tests were conducted under the next conditions; Working fluid were R-22 and R-134a, charging ratio 40% and 50%, temperature of inlet water $60^{\circ}C$ and $70^{\circ}C$, flow rates $1{\sim}3kg/min$. The experimental results indicate that the pulsating heat pipe charged 50% showed better performance than 40%, R-22 is more suited to the working fluid than R-134a, and it has a possibility which can be applied to floor heating panel using a pulsating heat pipe.