• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.2150-2158
• /
• 1992

This study was carried out to investigate the flow structure and mixing process of a cross mixing flow formed by two round jets with respect to the ratio of mass flow rate. This flow configuration is of great practical relevance in a variety of combustion systems, and the flow behaviour of a cross jet defends critically on the ratio of mass flow rate and the cross angle. The mass flow rate ratios of two different jets were controlled as 1.0, 0.8, 0.6, and 0.4, and the crossing angle of two round jets was fixed at 45 degree. The velocities issuing from jet nozzle with an exit diameter of 20mm were adjusted to 40m/s, 32m/s, 24m/s, and 16m/s, and the measurements have been conducted in the streamwise range of $1.1X_0$to $2.5X_0$ by an on-line measurement system consisted of a constant temperature type two channel hot-wire anemometry connected to a computer analyzing system. The original air flow was generated by a subsonic wind tunnel with reliable stabilities and uniform flows in the test section. For the analysis of the cross mixing flow structure in the downstream region after the cross point, the mean velocity profiles, the resultant velocity contours, and the three-dimensional profiles depending upon the mass flow rate ratio have been concentrately studied.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.177-180
• /
• 2010

Two-stage light gas gun, sorted with Ballistic Range System, is used to research spray characteristics of supersonic liquid jets. When high pressure tube was pressurized to the 135 bar, diaphragm films which composed with OHP film are ruptured. Expansion gases accelerate a projectile approximately 250 m/s at the exit of pump tube. And accelerated projectile collides with liquid storage part and liquid jets were injected into supersonic conditions. Supersonic liquid jets show the multiple jets and generate shockwave at the forward region of jets. Supersonic liquid jets of speed and shockwave angle have different value at each case. Supersonic liquid jets with minimum velocities are injected with M=1.53 at the geometry condition of L/d=23.8.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.482-482
• /
• 2013

반도체 소자의 미세화와 더불어 세정공정의 중요성이 차지하는 비중이 점점 커지고, 이에 따라 세정 기술 개발에 대한 요구가 증대되고 있다. 기존 세정 기술은 화학약품 위주의 습식 세정 방식으로 표면 손상, 화학 반응, 부산물, 세정 효율 등 여러 가지 어려움이 있다. 따라서 건식세정 방식이 활발하게 도입되고 있으며 대표적인 것이 에어로졸 세정이다. 에어로졸 세정은 기체상의 작동기체를 이용하여 에어로졸을 형성하고 표면 오염물질과 직접 물리적 충돌을 함으로써 세정한다. 하지만 이 또한 생성되는 에어로졸 내 발생 입자로 인해 패턴 손상이 발생하며 이러한 문제점을 극복하기 위하여 본 연구에서는 가스클러스터 장치를 이용한 세정 특성 평가에 관한 연구를 수행하였다. 가스 클러스터란 작동기체의 분자가 수십에서 수백 개 뭉쳐 있는 형태를 뜻하며 이렇게 형성된 클러스터는 수 nm 크기를 형성하게 된다. 그리고 짧은 시간의 응축에 의해 수십 nm 크기까지 성장하게 된다. 에어로졸 세정과 다르게 클러스터가 성장할 환경과 시간을 형성하지 않음으로써 작은 클러스터를 형성하게 되며 이로 인해 패턴 손상을 최소화 하고 상대적으로 높은 효율로 오염입자를 제거하게 된다. 클러스터 세정 장비를 이용한 표면 처리는 충돌에 의한 제거에 기반한다. 따라서 생성 및 가속되는 클러스터로부터 대상으로 전달되는 운동량의 정도가 세정 특성에 영향을 미치며 이는 생성되는 클러스터의 크기에 종속적이다. 생성 클러스터의 크기 분포는 분사 거리, 유량, 분사 각도, 노즐 냉각 온도 등의 변수에 관한 함수이다. 따라서 본 연구에서는 $CO_2$ 클러스터를 이용한 세정 특성을 평가하기 위하여 이러한 변수에 따라서 오염 입자의 종류, 크기에 따른 PRE (particle removal efficiency)를 평가하고 다양한 선폭의 패턴을 이용하여 손상 실험을 수행하였다. 제거 효율에 사용된 입자는 $CeO_2$와 $SiO_2$이며, 각각 30, 50, 100, 300 nm 크기를 정량적으로 오염시킨 쿠폰 웨이퍼를 제조하여 세정 효율을 평가하였다. 정량적 오염에는 SMPS (scanning mobility particle sizer)를 이용한 크기 분류와 정전기적 입자 부착 시스템이 사용되었다. 또한 패턴 붕괴 평가에는 35~180 nm 선폭을 가지는 Poly-Si 패턴을 이용하였다. 실험 결과 클러스터 형성 조건에 따라 상대적으로 낮은 패턴 붕괴에서 95% 이상의 높은 오염입자 제거효율을 전반적으로 보이는 것을 확인할 수 있었다. 따라서 이론적 계산에 기반하여 세정에 요구되는 클러스터 크기를 가정하고, 이를 통하여 세정에 적용할 경우 높은 기존 세정 방법의 단점을 보완하면서 높은 세정 효율을 가지는 대체 세정 방안으로 이용할 수 있음을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.110-120
• /
• 1986

45.deg. corss jet flow, at the mixing of two jet flows, was experimentally studied. For this study, only the statistical turbulent characteristics and high order moments will be analysed by on-line computer system (hot-wire anemometer system, dynamic analyser and computer system, plotting and printing system). Since mean velocity distributions, intensities of turbulence, Reynolds stresses, correlation coefficients, and other general results were already studied and presented. One dimensional probability density distributions of u', v', and w' were analysed comparing with Gaussian curve, which showed skew and flat tendency according to the Y and Z directions. For the analysis of the joint flow of turublent components, the joint probability density distributions were examined. The fagures were drawn so as to be read joint probabilities, joint probability densities, fluctuating velocities u', v', and w'. For further detailed examination of the variations of skewness and flatness phenomena, iso-joint probability density contours obtained from the profiles of the joint probability density distributions were studied. According to the displacement of positions from the center of the mixing flow and the directions, the flatness and skewness factors were increased.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.799-800
• /
• 2004

한전전력연구원에서는 한국표준형 원전 증기발생기인 시스템 80 모델의 튜브시트 상부에 침전된 슬러지를 제거하기 위한 고압 분사식 슬러지 세정장비를 개발하였다. 국내에는 영광 3,4,5,6 호기 및 울진 3,4,5,6 호기 등 총 8 기의 한국표준형 원전이 운전중에 있으나 기 사용하고 있던 증기발생기 세정 장비가 자동화가 미흡하여 작업자의 방사선 쪼임량이 과대하고 장비가 전열관에 충돌하여 전열관이 손상될 가능성이 상존하며 세정 방식이 증기발생기 가장자리인 annulus 에서 중앙의 center stay cylinder 로 향해 슬러지가 증기발생기 중앙 부분에 집중적으로 침적될 가능성이 있는 등 문제점을 해결하기 위하여 개발에 착수하였다. 개발된 증기발생기 세정 장비는 2004 년 4 월 중 울진 3 호기 증기발생기 세정 작업에 성공적으로 활용되었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.128-136
• /
• 2003

In today's design trend of vehicle structure, crush zone is fiequently reinforced by adding a box-shaped sub-frame in order to avoid an excessive deformation against a high-speed offset barrier such as EU Directive 96/97 EC, IIHS offset test. That kind of vehicle structure design results in a relatively monotonic crash pulse for airbag ECU(Electronic Control Unit) located at non-crush zone. As for an angular crash event, the measured crash signal using a single-axis accelerometer in a longitudinal direction is usually weaker than that of frontal barrier crash. Therefore, it is not so easy task to achieve a satisfactory crash discrimination performance for offset and angular crash events. In this paper, we introduce a new crash discrimination algorithm using an electronic X-Y 2-axis accelerometer in order to improve crash discrimination performance especially for those crash events. The proposed method uses a crash signal in lateral direction(Y-axis) as well as in longitudinal direction(X-axis). A crash severity measure obtained from Y-axis acceleration is used to improve the discrimination between fire and no-fire events. The result obtained by the proposed measure is logically ORed with an existing algorithm block using X-axis crash signal. Simulation and pulse injection test have been conducted to verify the performance of proposed algorithm by using real crash data of a 2,000cc passenger vehicle.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.9-14
• /
• 2020

Four developed patents have applied for a new type of Composite Cyclone Scrubber followed by the previous research (Cho and Kim, 2017), including dust reducing fan with filters. Regarding target installation and maintenance cost, 64% reduction for investment costs (6.2 billion won vs. 17 billion won) compared to existing road pollution reduction system, while social benefit costs increase by 43% compared to existing road pollution reduction measures (72.6 billion won vs. 50.8 billion won). The composition of the device is an air blower type spiral guide vane, and an injection pressure collecting dust efficiency. A nozzle varies Injection angle and contact range, spray liquid species (waterworks, salty water). The proposed patent tests are circulation water Time-by-Time Spray and collected 41.4% more increased micro dust since the sprayed water meets contaminated gas due to the 45° degree colliding, which is 141% increased conventional dust collector. (Ratio of collection over 85%). As regards the source of collection liquid, circulated rainwater and well water, we expect a huge amount of energy and economically saved eco-friendly system in our patent. Finally, the guided vane and metal filter reduced over 90% micro-dust, while sprayed water cleans the vane and filters, resultantly minimizing the maintenance budget. The preliminary evaluations of the developed design make it possible to reduce not only cheaper maintenance budget due to the characteristic water spraying but the cost of water comes from mainly rain and underground.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2204-2209
• /
• 2008

Flame pattern in burner used in steel industry that constitutes 30% of country energy consumption is generally characterized as long narrow flame pattern so that localized heating causes product quality worse and many burners are needed for proper heating. This paper deals with flat wide flame pattern which has advantage in terms of uniform heating using less number of burners. For that purpose, impinging jet system of fuel and oxidant was used for making flat wide flame. Results show that nozzle angle $75^{\circ}$ of impinging jet is found to be optimum configuration for making effective wide flame which has uniform radiation heat transfer and flame temperature is also most uniform along the flame width for that nozzle angle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.69-77
• /
• 1991

A collision-free trajectory planning algorithm using an iterative learning concept is proposed for dual robot arms in a 3-D common workspace to accurately follow their specified paths with constant velocities. Specifically, a collision-free trajectory minimizing the trajectory error is obtained first by employing the linear programming technique. Then the total operating time is iteratively adjusted based on the maximum trajectory error of the previous iteration so that the collision-free trajectory has no deviation from the specified path and also that the operating time is near-minimal. To show the validity of the proposed algorithm, a numerical example is presented based on two planar robots.

• Fire Science and Engineering
• /
• v.28 no.4
• /
• pp.1-7
• /
• 2014

Several complex devices and equipments are installed in the car's engine room, including various kind of oils or other flammable materials. So re-ignition is very likely to take place in it. In addition, it is restrictive for the driver or the occupant to open the bonnet and to spray the fire extinguisher in the engine room due to the high possibility of explosion. Therefore, a fire extinguishing system, which can detect a fire and inject the fire extinguishing agent to extinguish it, and fire extinguishing agents including HFC-227ea, which can stand the high temperature within the engine room and hold the viscosity sufficient to keep it in the kind of foam, were developed and tested. And the suffocation effect and the cooling effect come from the fire extinguishing principle of the foam fire extinguishing agent and the inhibiter catalyst effect come from the one of HFC-227ea was led simultaneously, and fire extinguishing agents without the secondary damage caused by residuals after the fire extinguishment like a case of the powder fire extinguishing agent, were developed. And experiments using a vehicle collision after the discharge is complete, foreign material can be removed without extinguishing the advantage that experimental results obtained.