• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.4
• /
• pp.427-438
• /
• 1994

This experimental study was earned out to examine the heat transfer characteristics of a 2-dimensional impinging air jet on a flat plate with a set of square rods. The objectives of the study were to investigate the flow and heat transfer characteristics caused by the square rods and to find out the optimum rods arrangement. Experiment was carried out first without using the rods to establish the baseline heat transfer performance. Then, rods of different widths and clearances were installed to cause the turbulence on the fluid flow.

• Journal of the Korean Solar Energy Society
• /
• v.23 no.4
• /
• pp.55-61
• /
• 2003

Heat transfer characteristics for an air jet vertically impinging on a flat plate with a set of hybrid rods was investigated numerically using the RNG k-$\varepsilon$turbulent model. A commercial finite-volume code FLUENT is used. The rods had cross sections of half circular and rectangular shapes. The heating surface was heated with a constant heat flux value of $1020W/m^2$. Parameters investigated were the jet Reynolds number, nozzle -to-plate spacing, the rod pitch and rod-to-plate clearance. The local and average Nusselt number were found to be dependent on the rod pitch and the clearance because installing rods disturbed the flow. Higher convective heat transfer rate occurred in the whole plate as well as in the wall jet region.

• Journal of ILASS-Korea
• /
• v.13 no.1
• /
• pp.9-15
• /
• 2008

This experimental study was carried out to examine the heat transfer characteristics of impinging air jet on a flat plate with a set of right angled triangle rods. Each right angled triangle rod in the array was positioned normal to the flow direction and parallel to the flat plate surface. The clearances from a right angled triangle rod to flat plate surface (C=1, 2 and 4 mm) and the distance from nozzle exit to flat plate (H=100 and 500 mm) were changed for the pitch between each right angled triangle rods (P=40 mm). As a result, heat transfer shows best performance at the clearance of C=1 mm, in case clearance changed, and the average heat transfer enhancement rate increased up to 47% compared to the result of a flat plate without a right angled triangle rod.

• Journal of Energy Engineering
• /
• v.13 no.1
• /
• pp.28-33
• /
• 2004

The objective of the study was to investigate the characteristics of heat transfer and flow in 2-dimensional impinging air jet system, in which trapezoid rods have been set up in front of impinging plate in order to increase heat transfer. Experiments were carried out first using without the rods to establish the baseline heat transfer performance. And this result compared with the experimentation with rods. When rods are installed in front of the impinging plate, the acceleration of the flow and the eddies due to the rods seem to contribute to the heat transfer enhancement. Heat transfer performance was best under the condition of C=1 n and as the pitch is 30 mm. In this case, maximum rate of heat transfer augmentation is about 1.62 times greater compared to that without trapezoid rods.

• Solar Energy
• /
• v.17 no.1
• /
• pp.47-58
• /
• 1997

The objective of this research was to investigate the enhancement of heat transfer by wire mesh in impinging air jet system at the potential core region. The first experiment was carried out without mesh between nozzle exit and flat plate and the second experiment was done with mesh between them. When mesh was installed in front of the plate, heat transfer has been Increased due to the acceleration between rectangular halls and divided small jet In case clearances are changed, heat transfer comes to maximum under the condition of C=1mm, irrespective of nozzle exit velocity and H/B. Also the average heat transfer enhancement rate of a flat plate with mesh has been increased about 44% at maximum under the condition of U=18m/s, H/B=2 and C=1mm, compared to the result of a flat plate without mesh.

• Solar Energy
• /
• v.15 no.3
• /
• pp.127-140
• /
• 1995

This experimental study was carried out to examine the heat transfer characteristics of a 2-dimensional impinging air jet on a flat plate with a set of square rods. The objectives of the study were to investigate the flow and heat transfer characteristics caused by the square rods. Experiment was carried out first without using the rods to establish the baseline heat transfer performance. Then, rods of different widths and clearances were installed to cause the turbulence on the fluid flow. When rods are installed in front of the plate, the acceleration of the flow and the turbulence generation due to the rods and reattachment of the flow seem to contribute to the observed heat transfer augmentation and the heat transfer augmentation increases as the clearance decreases. With wider individual rod the heat transfer coefficient is higher, which is due to the increased acceleration and development of the eddies just before the rods.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.180-180
• /
• 2013

반도체, 디스플레이와 같이 저압, 극청정 조건에서 진행되는 공정에서 발생한 오염입자는 수 율에 큰 영향을 미친다. 따라서 공정 중에 발생한 오염입자를 실시간으로 모니터링할 수 있는 장비에 대한 연구가 활발히 진행되고 있다. Particle Beam Mass Spectrometer (PBMS)는 저압에서 실시간으로 나노 입자의 크기를 측정할 수 있는 대표적인 장비 중 하나이다. 입자를 포함한 가스 유동이 PBMS로 유입되면, 우선 입자를 입자빔의 형태로 집속하는 공기역학렌즈를 통과하게 된다. 집속된 입자는 노즐에 의해서 가속되며, 이로 인해 충분한 관성을 가지게 된 입자는 양극과 음극, 필라멘트로 구성된 electron gun에서 전자충돌에 의해 포화상태로 하전된다. 하전한 입자는 electrostatic deflector에서 크기에 따라 분류되어 Faraday detector와 electrometer에 의해 측정된다. 그러나 공기역학렌즈는 입자의 크기가 작아질수록 집속 효율이 급격히 낮아진다는 문제점을 지니고 있다. 이는 입자가 작아질수록 점성에 의한 영향이 관성에 의한 영향보다 커짐으로써 나타나는 현상이다. 최근 이러한 문제점을 해결하기 위해 사중극자를 사용하여 입자를 집속시키는 방법이 대안으로 제시되었다. 사중극자는 서로 마주보는 쌍곡선 형태의 전극구조에 AC 전기장을 인가하는 방식을 사용한다. 사중극자의 중심은 정확히 평형점을 가지게 되며 입자는 사중극자 내에서 진동을 반복하며 평형점을 향해 모이게 된다. 입자의 크기가 작을수록 전기력에 의한 영향을 크게 받으므로 사중극자를 이용한 입자집속 방법은 나노입자의 집속에 있어 공기역학렌즈를 이용한 집속에 비해 이점을 지닌다. 또한 집속 하고자 하는 입자 대상이 바뀔 경우 구조를 바꿔야 하는 공기역학렌즈와 달리 사중극자를 이용한 방법은 AC 전기장을 조절하는 것 만으로 제어가 가능하다. 본 연구에서는 저압 조건에서 나노입자를 집속하기 위한 사중극자의 전극 구조를 이론적인 계산을 통하여 구하였다. 그 결과 0.1 torr의 압력 조건하에서 5~100 nm 범위의 기본 입자를 AC 전압과 진동수를 조절하여 집속할 수 있는 사중극자 형태를 설계하였다.

• Solar Energy
• /
• v.15 no.1
• /
• pp.85-94
• /
• 1995

This research has been proceeded over the potential core region(H/B=2) of two-dimensional impinging air jet sytem, in which square rods(width of 6 mm) has been set up in front of heating surface in order to increase heat transfer. The objective of this research was to investigate the characteristics of heat transfer and air flow, in eases of the clearance from rods to heating surface(C=1, 2, 4, 6 mm) and the pitch between each rods(P=30, 40, 50 mm) changed. And this research compared the above with the experimentation without rods. As result, heat transfer performance was best under the condition of C=1mm, in case clearance changed, and there was no serious difference in the effect of heat transfer augmentation in the case of pitch of rods changed.

• Solar Energy
• /
• v.13 no.1
• /
• pp.22-30
• /
• 1993

This Paper deals with the experimental study of the axisymmetric air jet impinging vertically on the flat heating surface with and without swirl. The purpose of this study is to investigate the characteristics of flow, augmentation of heat transfer rate, turbulent intensity, and the comparison of heat transfer rate, the optimal swirling condition about the swirl and nonswirl axisymmetric air jet. In order to augment the heat transfer on the flat heating surface without introducing any additional power, the technique used in the present work was placement of twisted tape inserted pipe in front of the nozzle exit in order to make a swirl. The effect of swirl degree is investigated in case of S=0., 0.056, 0.111, 0.222 and the velocity of the jet was 14, 20, 26, 32, 38, 44m/s. The distance between the nozle exit and the stagnation point on the impinging plate was the H/D=$1{\sim}14$. In order to analyze of the flow structure which increase heat transfer, the velocity and the turbulent intensity of the axisymmetric jet was measured by a hot wire anemometer according to the swirl number and H/D.

• Solar Energy
• /
• v.13 no.1
• /
• pp.11-21
• /
• 1993

The purpose of this study was to investigate the enhancement of heat transfer without additional external power in the case of rectangular impingement air jet vertically on the flat heating surface. The technique used in the present study was placement of square rod bundles as a turbulence promoter in front of the heat transfer surface. The results obtained through this study were summerized as follws. High heat transfer enhancement was achieved by inserting rods in front of the heating flat plate. According to visulaization, it was examined because of flow acceleration and separation and disturbance of boundary layer. The smaller clerance between rod and heating plate was, the larger heat transfer effect became at each H/B. Arverage Nusselt number reached maximum at H/B=10 and the local augmentation rate of heat transfer became maximum at H/B=2. The maximum average heat transfer enhancement rate increase about 43% for the case of X/B=2 and C=1mm, compared to a flat plate without rods. The correlating equation of average Nusselt number and Reynolds number was obatined. As follws : ${\overline{Nu}}_0=1.249Re^{0.465}(C/A)^{-0.033}(H/B)^{0.013}$.