• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.84-84
• /
• 2000

수소화된 비정질 실리콘(a-Si:H)과 미세결정질 실리콘 ($\mu$c-Si:H)은 저온.건식 공정인 PECVD로 값싼 유리 기판을 사용하여 넓은 면적에 증착이 가능하다는 큰 장점으로 인해 광전소자(photovoltaic device)와 박막 트랜지스터(TFTs)등에 폭넓게 응용되어 왔으며 최근에는 nm 크기의 실리콘 결정(nc-Si)에서 가시광선 영역의 발광 현상이 발견됨에 따라 광소자로서의 특성을 제어하기 위해서는 성장 조건과 공정 변수에 따른 구조 변화에 대한 연구가 선행되어야 한다. 본 연구에서는 UHV-ECR-PECVD 법을 이용하여 H2로 희석된 SiH4로부터 a-Si:H과 $\mu$c-Si:H를 증착하였다. 그림 1은 SiH4 20sccm/H2 50sccm/25$0^{\circ}C$에서 기판의 DC bias를 변화시키면서 박막을 증착시킬 때 나타나는 박막의 구조 변화를 raman spectrum의 To phonon peak의 위치와 반가폭의 변화로 나타낸 것이다. 비정질 실리콘 박막은 DC bias를 증가시킴에 따라 무질서도가 증가하다가 어떤 critical DC bias에서 최대치를 이룬후 다시 질서도가 증가한다. 이온의 충격력에 의해 박막내에 응력이 축적되면 박막의 에너지 상태가 높아지고 이 축적된 응력이 ordering에 대한 에너지 장벽을 넘을 수 있을 만큼 커지게 되면 응력이 풀리면서 ordering이 가능해지는 것으로 생각된다. 그림 2는 수소 결합 형태의 변화이다. 박막의 무질서도가 증가할 경우 알려진 바와 같이 2000cm-1근처의 peak은 감소하고 2100cm-1 부근이 peak이 증가하는 현상을 보였다. 본 논문에서는 여러 공정 변수, 특히 DC bias에 따르는 박막의 구조 변화와 다른 성장 조건(온도, 유량비)이 critical DC bias나 결정화, 결정성 등에 미치는 영향에 대한 분석결과를 보고하고자 한다.등을 이용하여 광학적 밴드갭, 광흡수 계수, Tauc Plot, 그리고 파장대별 빛의 투과도의 변화를 분석하였으며 각 변수가 변화함에 따라 광학적 밴드갭의 변화를 정량적으로 조사함으로써 분자결합상태와 밴드갭과 광 흡수 계수간의상관관계를 규명하였고, 각 변수에 따른 표면의 조도를 확인하였다. 비정질 Si1-xCx 박막을 증착하여 특성을 분석한 결과 성장된 박막의 성장률은 Carbonfid의 증가에 따라 다른 성장특성을 보였고, Silcne(SiH4) 가스량의 감소와 함께 박막의 성장률이 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 줄어들어 성장률이 Silane가스량에 의해 지배됨을 볼 수 있다. UV-VIS spectrophotometer에 의한 비정질 SiC 박막의 투과도와 파장과의 관계에 있어 유리를 기판으로 사용했으므로 유리의투과도를 감안했으며, 유리에 대한 상대적인 비율 관계로 투과도를 나타냈었다. 또한 비저질 SiC 박막의 흡수계수는 Ellipsometry에 의해 측정된 Δ과 Ψ값을 이용하여 시뮬레이션한 결과로 비정질 SiC 박막의 두께를 이용하여 구하였다. 또한 Tauc Plot을 통해 박막의 optical band gap을 2.6~3.7eV로 조절할 수 있었다. 20$0^{\circ}C$이상으로 증가시켜도 광투과율은 큰 변화를 나타내지 않았다.부터 전분-지질복합제의 형성 촉진이 시사되었다.이것으로 인하여 호화억제에 의한 노화 방지효과가 기대되었지만 실제로 빵의 노화는 현저히 진행되었다. 이것은 quinua 대체량 증가에 따른 반죽의 안정성이 저하되어 버린 것으로 생각되어진다. 더욱이 lipase를 첨가하면 반죽이 분화하는 경향이 보여졌지만 첨가량 75ppm에 있어서 상당히 비용적의 증대가 보였다. 이것은 lipase의 가수분해에 의해

• KIPS Transactions on Software and Data Engineering
• /
• v.8 no.6
• /
• pp.243-250
• /
• 2019

Because of a moving UAV has a lot of potential/kinetic energy, if the UAV falls to the ground, it may have a lot of impact. Because this can lead to human casualities, in this paper, the population density area on the UAV flight path is defined as a dangerous area. The conventional UAV path flight was a passive form in which a UAV moved in accordance with a path preset by a user before the flight. Some UAVs include safety features such as a obstacle avoidance system during flight. Still, it is difficult to respond to changes in the real-time flight environment. Using public Big Data for UAV path flight can improve response to real-time flight environment changes by enabling detection of dangerous areas and avoidance of the areas. Therefore, in this paper, we propose a method to detect and avoid dangerous areas for UAVs by utilizing the Big Data collected in real-time. If the routh is designated according to the destination by the proposed method, the dangerous area is determined in real-time and the flight is made to the optimal bypass path. In further research, we will study ways to increase the quality satisfaction of the images acquired by flying under the avoidance flight plan.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.361-370
• /
• 2021

Carbon fiber reinforced polymer (CFRP) is one of the composite materials, which has a unique property that is lightweight but strong. The CFRPs are widely used in various industries where their unique characteristics are required. In particular, electric and unmanned aerial vehicles critically need lightweight parts and bodies with sufficient mechanical strengths. Vehicles using the battery as a power source should simultaneously meet two requirements that the battery has to be safely protected. The vehicle should be light of increasing the mileage. The CFRP has considered as the one that satisfies the requirements and is widely used as battery housing and other vehicle parts. On the other hand, in the battery area, carbon fibers are intensively tested as battery components such as electrodes and/or current collectors. Furthermore, using carbon fibers as both structure reinforcements and battery components to build a structural battery is intensively investigated in Sweden and the USA. This mini-review encompasses recent research trends that cover the classification of structural batteries in terms of functionality of carbon fibers and issues and efforts in the battery and discusses the prospect of structural batteries.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.9
• /
• pp.13-20
• /
• 2011

There are many mountains in Korean Peninsula, and those used for the construction of roads and railways sectors are forming slopes. Slope collapse occurs with falling rocks and landslide because of the relaxation of the thawing rocks. The heavy rain in summer can also significantly contribute to the process, and abnormal climate change is much more influential than before. Therefore, rockfall-related accidents in rainy season are easily accessible in media every year. There has been a lot of research on application of strengthening compensation of the sections in order to minimize casualties and property damage. Rockfall Protection Net, however, has not been focused on much in the field yet. This study highlights the need of Rockfall Protection Net, since it can segregate the falling rocks inside the net relatively safely. Although there has been a little doubt about the effectiveness of rockfall protection facilities, it is obvious that relevant studies dealing with the solidity of the net are necessary for the rockfall protection net to be capable of supporting rockfall energies. As a result, Expanded metal strength is much more durable compared to the PVC coating net, and it is regarded as an excellent alternative material for the Rockfall Protection Net. In this study, the applicability of Expanded Metal as the alternative of Rockfall Protection Net is verified experimentally.

• International Area Studies Review
• /
• v.21 no.4
• /
• pp.223-245
• /
• 2017

This study is examined interaction between carbon market with stock market using a multivariate GARCH(DCC) model. Carbon market is EU ETS EUA price, stock market is the iron and cement stock price which has relatively energy intensive and massive carbon emissions sector in the industrial sector. It also analyzed changes in the correlation between the markets through an analysis of correlation coefficients. Moreover, it checked whether there was marketability expansion(or expansion of carbon emissions reduction) through the analysis above. As a result of empirical tests, it showed that the price spillover effect was insignificant. In addition, it represented that there was a weak correlation between the two markets since the volatility spillover effect disappeared in the second phase by an external shock(a financial crisis). Moreover, it was revealed that there were no significant changes although there was a weak upward trend in terms of the correlation between the carbon market and the stock market. This implies that emission rights could not expand marketability to financial market as a commodity(or did not play its natural role of the reduction of carbon emission).

• Journal of Animal Environmental Science
• /
• v.6 no.3
• /
• pp.175-184
• /
• 2000

A lab-scale MF membrane reactor was installed to investigate the membrane permeability, characteristics of membrane fouling at each conditions, and quality of permeate (liquid livestock manure) in the separation of solid-matters using membrane. Experiment was divided three filtration type such as follows; continuous filtration, gravity filtration, and intermittent filtration. As a result of experiment, flux 1 LMH was maintained for 7days, and trans-membrane pressure(TMP) was increased gradually under 10cmHg, but it was increased immediately after 10cmHg, respectively. However, the flux was increased, the Tmax was decreased exponential more and more. During the pure-flux test, most of the fouling of membrane was reversible. At the gravity filtration, permeate could be obtained as 1.75 LMH for 3.5days without any other electronic pressure. As an investigation of membrane surface, this study could be decided that the reason of fouling at the lower flux (Run 1 and 2) was attached matters in membrane surface, but at the higher flux (Run 4-6) was concentration polarization.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.9 no.3
• /
• pp.188-194
• /
• 2007

The relationships between pine mushroom emergence and meteorological factors were analyzed with three years (from 2003 to 2005) of measurement data at Yangyang site, in order to evaluate the effect of micrometeorological environment on pine mushroom production. fine mushroom was daily monitored and collected in the survey area during the its producing period (approximately one month). Pine mushroom production was highest in 2005 with the meteorological conditions of high temperature and frequent rainfalls in October. The production was lowest in 2004 due to dry conditions from mid September to late October, The meterological factors related to humidity (i.e., relative humidity, soil water content, and precipitation) were better correlated than those related to temperature (i.e., air and soil temperature, soil heat flux and solar radiation) with pine mushroom production. However, all of the correlation coefficients were statistically insignificant with values ranging from 0.15 to 0.46. Such poor correlations may be attributed to various other environmental conditions (e.g., topography, soil, vegetation, other fungi, the relationship between pine mushroom and pine forest) affecting pine mushroom production. We found that a mycelium requires a stimulation of low temperature (of three-day moving average) below $19.5^{\circ}C$, in order to farm a mushroom primordium which grows to pine mushroom after 16 days from the stimulation. We also found that the pine mushroom production ended when the soil temperature (of three-day moving average) fell below $14.0^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.68-87
• /
• 1982

In Korea, this is the situation at moment that the total demand of timber in 1972 is more than 5 million cubic meters. On the other hand, however, the available domestic supply of timber at the same year is only about, 1 million cubic meters. A great unbalancing between demand and supply of timber has been prevailing. To solve this hard problem, it has been necessitiated to build up the forest stocks as early as possible with fast grown species such as poplar. Under circumstances, poplar plantations which have been carryed on government and private have reached to large area of 116,603 hectors from 1962 up to date. It has now be come a principal timber resources in this country, and required the basic study on various properties of wood for it's proper utilization, since it has not been made of any systematic study on the properties of Populus grown in Korea. In order to investigate the properties such as anatomical, physical and mechanical properties of nine different species (P. euramericana Guiner I-214. P. euramericana Guiner I-476, P. deltoides Marsh, P. nigra var. italica (Muchk) Koeme, P. alba L.,P. alba $\times$ glandulosa P. maximowiczii Henry, P. koreana Rehder, P. davidiana Dode) of poplar for their proper use and development of new ways of grading processing and quality improving, this study has been made by the Forest Research Institute.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5A
• /
• pp.565-575
• /
• 2009

In recent years, there have been numerous explosion-related accidents due to military and terrorist activities. Such incidents caused not only damages to structures but also human casualties, especially in urban areas. To protect structures and save human lives against explosion accidents, better understanding of the explosion effect on structures is needed. In an explosion, the blast load is applied to concrete structures as an impulsive load of extremely short duration with very high pressure and heat. Generally, concrete is known to have a relatively high blast resistance compared to other construction materials. However, normal strength concrete structures require higher strength to improve their resistance against impact and blast loads. Therefore, a new material with high-energy absorption capacity and high resistance to damage is needed for blast resistance design. Recently, Ultra High Strength Concrete(UHSC) and Reactive Powder Concrete(RPC) have been actively developed to significantly improve concrete strength. UHSC and RPC, can improve concrete strength, reduce member size and weight, and improve workability. High strength concrete are used to improve earthquake resistance and increase height and bridge span. Also, UHSC and RPC, can be implemented for blast resistance design of infrastructure susceptible to terror or impact such as 9.11 terror attack. Therefore, in this study, the blast tests are performed to investigate the behavior of UHSC and RPC slabs under blast loading. Blast wave characteristics including incident and reflected pressures as well as maximum and residual displacements and strains in steel and concrete surface are measured. Also, blast damages and failure modes were recorded for each specimen. From these tests, UHSC and RPC have shown to better blast explosions resistance compare to normal strength concrete.

• Applied Chemistry for Engineering
• /
• v.21 no.2
• /
• pp.217-223
• /
• 2010

In general, fiber-reinforced plastics (FRP) wastes are simply buried or burned. Landfill brings about a permanent contamination of soil due to the inability of FRP to decompose and incineration causes an issue of generating toxic gases and dusts. There have been several ways to treat the FRP wastes such as landfill, incineration, chemical recycling, material recycling and the utilization of energy from combustion. Most methods excluding material recycling are known to have critical limitations in economic, technical and environmental manners. However it is known that material recycling is most desirable among the methods handling FRP wastes. In this study, to investigate the purpose of feasibility of material recycling, various bulk molding compound (BMC) specimens were prepared with the various contents of unsaturated polyester resin binder (25, 30, 35 wt%) and the various replacement ratios of FRP wastes powder (0, 25, 50, 75, 100 wt%) substituted for filler. To evaluate the physical properties BMC specimens, various tests such as tensile strength, flexural strength, impact strength, hot water resistance and SEM imaging were conducted. As a results, mechanical strengths decreased with an increase of replacement ratio of FRP waste powder and physical properties of BMC specimens were deteriorated in the hot water resistance. The fluidity of BMC with more than 50 wt% of the replacement ratio of FRP wastes powder decreased remarkably, causing a problem in the BMC composite.