• The Journal of Korean Society for Radiation Therapy
• /
• v.29 no.2
• /
• pp.65-73
• /
• 2017

Purpose: Machine Performance Check (MPC) is a self-checking software based on the Electronic Portal Imaging Device (EPID) to measure daily beam outputs without external installation. The purpose of this study is to verify the usefulness of MPC by comparing and correlating daily beam output of QA Beamchecker PLUS. Materials and Methods: Linear accelerator (Truebeam 2.5) was used to measure 10 energies which are composed of photon beams(6, 10, 15 MV and 6, 10 MV-FFF) and electron beams(6, 9, 12, 16 and 20 MeV). A total of 80 cycles of data was obtained by measuring beam output measurement before treatment over five months period. The Pearson correlation coefficient was used to evaluate the consistency of the beam output between the MPC and the QA Beamchecker PLUS. In this study, if the Pearson correlation coefficient is; (1) 0.8 or higher, the correlation is very strong (2) between 0.6 and 0.79, the correlation is strong (3) between 0.4 and 0.59, the correlation is moderate (4) between 0.2 and 0.39, the correlation is weak (5) lower than 0.2, the correlation is very weak. Results: Output variations observed between MPC and QA Beamchecker PLUS were within 2 % for photons and electrons. The beam outputs variations of MPC were $0.29{\pm}0.26%$ and $0.30{\pm}0.26%$ for photon and electron beams, respectively. QA Beamchecker PLUS beam outputs were $0.31{\pm}0.24%$ and $0.33{\pm}0.24%$ for photon and electron beams, respectively. The Pearson correlation coefficient between MPC and QA Beamchecker PLUS indicated that photon beams were very strong at 15 MV, and strong at 6 MV, 10 MV, 6 MV-FFF and 10 MV-FFF. For electron beams, the Pearson correlation coefficient were strong at 16 MeV and 20 MeV, moderate at 9 MeV and 12 MeV, and very weak at 6 MeV. Conclusion: MPC showed significantly strong correlation with QA Beamchecker PLUS when testing with photon beams and high-energy electron beams in the evaluation of daily beam output, but the correlation when testing with low-energy electron beams (6 MeV) appeared to be low. However, MPC and QA Beamchecker PLUS are considered to be suitable for checking daily beam output, as they performed within 2 % of beam output consistency during the observation. MPC which can perform faster than the conventional daily beam output measurement tool, is considered to be an effective method for users.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.10
• /
• pp.1409-1415
• /
• 2021

The Gysel divider has the advantage of easily setting the resistor in the circuit. If the line impedance in the Gysel divider is set differently, the input signal can be distributed to the two output ports at various distribution ratios. This paper proposes the Gysel divider that can change the power distribution to 1:3 or 3:1 by changing the line impedance. The impedance change of the line can be implemented by placing a floating copper plate on the bottom of the microstrip-line. When the floating copper plate and the ground plane are connected, the line operates as the microstrip-line, and when the floating copper plate and the ground plane are disconnected, the line operates as the coplanar-line. The proposed Gysel divider was fabricated at the center frequency of 1.5GHz. The fabricated 3:1 Gysel divider has a stable value S₁₁ of below -17dB, S₂₁/S₃₁ of 4.8±0.2dB, S₂₁(to high output port) of -1.39±0.12dB and S₃₁(to low output port) of -6.15±0.08dB over 1.3~1.7GHz.

• Korean Journal of Optics and Photonics
• /
• v.10 no.5
• /
• pp.396-400
• /
• 1999

In the fiber-optic gyroscope employing a high-power erbium-doped fiber source, the source excess noise was subtracted from the gyro output through a single processing to improve the gyroscope sensitivity. As the result, we obtained the reduction of noise by 13.5 dB (electrical) which was measured from the noise floor spectrum when the gyro was modulated with the depth of 1.8 rad. In addition, the random walk coefficient of the gyro output was reduced by a factor of 4~5.

• Journal of Industrial Technology
• /
• v.31 no.A
• /
• pp.123-128
• /
• 2011

In this study, procedures, a power performance testing system of Wind Turbine System Research Center of Kangwon National University is introduced. Test prodedures and results are presented on a stand-alone vertical-axis 200W wind turbine manufactured by Geum-Poong Energy Inc.. Power performance test is performed according to IEC standard. The test results are compared with the power performance standard. Also, the effects of normalization and disturbed sectors are considered.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.11
• /
• pp.917-926
• /
• 2012

The analysis of aerodynamic characteristics for aircraft propellers is studied to develop high efficiency composite propellers. It is to verify the accuracy and reliability of predicting the efficiency characteristics of aircraft propellers by applying nonlinear numerical analysis. The numerical simulation method incorporated the CFD code, which is based on RANS (Reynolds Averaged Navier-Stocks) equation. The study includes a comparative analysis between the numerical simulation results and the wind tunnel test results of the full-scale aircraft propeller. The comparison shows that thrust and power coefficients of the propeller calculated by nonlinear numerical analysis are higher than those based on the results generated from the wind tunnel test. The efficiency of the propeller calculated by numerical analysis matches closely to the efficiency based on the wind tunnel test results. The verification results are analyzed, then, will be used in optimizing the design and manufacture of the subject aircraft propeller studied.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.1044-1052
• /
• 1999

A 2-stage 1 watt MMIC(Monolithic Microwave Integrated Circuits) HPA(High Power Amplifiers) at 20 GHz band has been designed and fabricated. The $0.15\mu\textrm{m}$ with the width of $400\mu\textrm{m}$for single device pHEMT technology was used for the fabrication of this MMIC HPA. Due to the series feedback technique from source to ground, bias circuits and stabilization circuits on the main microstrip line, the stability factors(Ks) are more than one at full frequency. The independent operation for each stage and excellent S11, S22 less than -20 dB have been obtained by using lange couplers. For beginning the easy design, linear S-parameters have been extracted from the nonlinear equivalent circuit in foundry library, and equivalent circuits of devices at in/output ports were calculated from this S-parameters. The measured performances, which are in well agreement with the predicted ones, showed the MMIC HPA in this paper has the minimum 15 dB of linear gain, -20 dB of reflection coefficients and 31 dBm of output power over 17~25 GHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.693-695
• /
• 2015

The design and implementation of a broadband and linear HPA for TVWS are presented in this paper. The spectrum mask and transmitted power of HPAs for TVWS must be controlled and meet the regulations to minimize interference effects on the present broadcasting systems. The implemented HPA has the operating frequency of 470 ~ 698MHz with the maximum 48.63dB and minimum 43.45dB gain, input reflection coefficient of below -21.32dB, output reflection coefficient of below -4.29dB and the linearity of -45.24dBc at 28.79dBm output power.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.4
• /
• pp.186-191
• /
• 2018

As influence of the 4th industry is growing with development of information society more electronic devices and sensor are used in the field. As this is the case, importance of signal processing during data transfer is rising Furthermore, the need for technology to remove noise caused by various reasons and to stabilize sensor output is growing as well. This research suggests digital filter algorithm that efficiently remove noise by stabilizing output of accelerating sensor. The standard value of this algorithm is calculated by applying Gaussian coefficient. To maintain its feature, final output is obtained by subtracting weight depending on variance from standard value For its evaluation, it is compared with other protocols and its function is checked through output features.

• Journal of the Korea Society of Computer and Information
• /
• v.4 no.1
• /
• pp.76-84
• /
• 1999

For FH/SS communication, We discussed the method of indirect frequency synthesizer in several methods. The problem of sing1e frequency synthesizer using with PLL is a varied coefficient value of damping factor in frequency hopping time, which is caused unstable frequency. So. for stable frequency synthesizer, a coefficient of damping factor must be optimized and synthesized to be removed excessive response time. In this paper, we studied FH using with double loop frequency synthesizer which takes stable frequency. We made up a simulator and had a good performance(real time speed).

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.311-312
• /
• 2006

본 논문에서는 선로 전력조류제약을 고려한 경제급전(SCED : Security-Constrained economic dispatch)에 내점 선형계획법을 이용하여 최적해를 구하는 문제를 다룬다. 최적전력조류(Optimal Power Flow)식으로부터 선로의 유효전력만을 근사화하여 선로 전력조류 제약을 고려할 경제급전(SCED)의 식을 정식화한다. 선형계획법을 적용하여 최적해를 구하기 위해서 발전기출력과 유효전력, 부하, 손실과의 관계를 이용하여 경제급전의 식을 선형화 하는 알고리즘을 제시한다. 선형화 알고리즘은 목적함수로 계통 발전기의 총 연료비를 취하고 전력수급평형식으로 발전기출력증분에 대한 선로의 증분손실계수를 이용하며, 선로의 제약조건은 일반화발전 분배계수(GGDF : Generalized Generation Distribution Factor)를 이용하여 선형화한다. 최적화 기법으로서 내점법(Interior Point Method)을 적용하고자 하며 사례연구를 통하여 선형계획법 중 가장 많이 사용하는 심플렉스(Simplex)법과의 수렴특성을 비교하여 내점 법의 효용성을 확인하고자 한다.