• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.1
• /
• pp.46-52
• /
• 2000

A computational analysis has been made on fluid flow in a regenerative cooling Passage for a reduced size liquid rocket engine to predict pressure drop and heat transfer rate in it. The contraction/expansion of the cross sectional area of the passage turn out to increases both the pressure loss and the heat transfer rate of the duct. The changes of the cross sectional area near the nozzle throat are effective to protect the throat which suffers from severe thermal load. Also given is the qualitative characteristics of the performance of the regenerative cooling system due to the variation of coolant flow rate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1056-1067
• /
• 1997

Present study visualized flow pattern and investigated spray characteristics of twin-fluid atomization with converging-diverging nozzles. Particle sizes were measured by using the Malvern particle analyzer, and the radial size distributions were evaluated by using the tomographic transform technique. The results show that the SMD generally increases in the radial direction at a prescribed liquid flow rate and the increasing rate in the SMD becomes gradual as atomizing gas pressure increases. The SMD decreases as the liquid flow rate increases at a fixed GLR (gas/liquid mass ratio). The atomization performance of the protrusion-type nozzle turned out to be superior to that of the flush-type. However, in the case of the protrusion-type, flow separation occurs outside the liquid delivery tube when the pressure at the gas nozzle chamber is high enough, which may deteriorate the atomization performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.70-77
• /
• 2000

Supersonic Dual Bell Nozzle (SDBN) is an altitude-adaptive propulsion nozzle achieved only by a nozzle wall inflection. In order to investigate the altitude adaptive capability and the effectiveness of this nozzle concept, the present study addresses a computational work of the flow through SDBN. Several types of the SDBNs are tested for a wide range of the pressure ratio which covers from an over-expended flow to a fully under-expended flow at the exit of the SDBN. Axisymmetric, compressible, Wavier-Stokes equations are numerically solved using a fully implicit finite volume differencing scheme. The present computational results reveal that the base nozzle length affects the shock wave system occurring inside SDBN. For a quit wide range of the pressure ratio the flow separation occurs at the nozzle inflection point. It is found that the maximum thrust coefficient is obtainable for the correct expansion state at the exit of SDBN.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.89-95
• /
• 2000

To obtain an exact flow loss in piping systems is very important in the face of efficiency anticipation and work control of plant. The object of this study is to get the flow loss through the experiment for sudden expansion and contraction part of circular pipe nozzle. The experiment in this study is performed after getting the flow loss factor for sudden expansion and contraction through preliminary experiments. It is confirmed that the results of this study agreed with the approximated equation of Ikeda and Matsuo. It is proved that flow loss factor ${\zeta}_3$for sudden expansion and contraction part of circular pipe is dependent on $L/D_1$in these experimental conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.2
• /
• pp.42-50
• /
• 2012

The goal of heat transfer studies is the accurate prediction of temperature and heat flux distribution on material boundaries. To this purpose, general-purpose computational fluid dynamics(CFD) code is used : FLUENT. Mass fluxes and pressure ratio are calculated for two types of nozzle. The comparative studies reveal that the computational results are in agreement with the experimental data. Also, heat transfer coefficients from FLUENT for one type of nozzle are very similar and agree well with the experimental data in the diverging part of the nozzle, but the calculated results are large in the converging part. The heat transfer coefficients from Bartz equation are over-predicted. We can consider various reasons for these differences, i.e., laminarization by the highly accelerated flow in the nozzle, turbulent flow model and grid generation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.167-171
• /
• 2012

A computational analysis of nozzle flow is conducted to investigate effects of the flight altitude on thrust performance. Reynolds-averaged Navier-Stokes equation with k-${\omega}$ SST(Shear Stress Transport) turbulence model is employed to simulate the nozzle flow in various altitude conditions, where continuum mechanics is to be valid. Thrust performance of the nozzle is exceedingly poor upto 10 km of flight altitude because of the irreversible phenomena such as shock and/or flow separation occurring inside the nozzle, whereas it is restored to the nominal value as the altitude is attained higher than 30 km.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.62-69
• /
• 2014

This paper presents a preliminary study of a convergent divergent nozzle in an afterburning turbofan engine of a supersonic aircraft engine. In order to design a convergent divergent nozzle, cycle model of a low bypass afterburning turbofan engine of which thrust class is 29,000 lbf at a sea level static condition is established. The cycle analysis at the design point is conducted by Gasturb 12 software and one dimensional gas properties at a downstream direction of the turbine are obtained. The dimension and configuration of an model turbofan engine are derived from take-off operation with wet reheat condition. The off-design cycle calculation is conducted at the all flight envelope on the maximum flight Mach number of 2.0 and maximum flight altitude of 15,000 m.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.4
• /
• pp.1-8
• /
• 2014

Overexpanded flow of an axisymmetric thruster nozzle is numerically simulated to investigate effects of nozzle pressure ratio (NPR) on the shock structure and thrust performance. The Reynolds-averaged Navier-Stokes equations with k-${\omega}$ SST turbulence model are solved utilizing FLUENT solver. As the NPR is raised, thrust performance monotonically increases with the shock structure and flow-separation point being pushed toward the nozzle exit. It is also discussed that the flow structure at nozzle-exit plane which is immediately affected by a position of nozzle-interior shocks and expansion waves, has strong influence upon the thrust performance of thruster nozzle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.1-9
• /
• 2013

Variable area nozzle, where both throat and exit area vary, is required for optimal expansion and optimal nozzle shape upon operation of after-burner. Steady-state and transient analyses are carried out for each condition with and without afterburner operation and as a function of the location of the nozzle flap. Effects of that nozzle displacement on flow and thrust characteristics are analyzed from numerical results. With variable area nozzle adopted, the combustion field is variable in time, leading to periodically variable thrust. For off-design conditions, flow separation shows up due to over expansion at the flap tips and shock wave does in the nozzle due to under expansion. The undesirable phenomena can be solved by control of variable area nozzle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.2
• /
• pp.1-7
• /
• 2002

In the modern propulsion systems, requited thrust is obtained using a nozzle. Sometimes shock and induced boundary layer separation is generated in an over-expanded convergent-divergent supersonic nozzle. It occurs because the nozzle expansion ratio is too large for a given nozzle pressure ratio (NPR). This phenomenon can be explained that it redefines effective nozzle geometry, shorer nozzle geometry and lower pressure ratio, in a given pressure ratio. Numerical studies were conducted about a fixed geometry 2D nozzle in overexpanded condition and compared with Hunter's experimental result. For the numerical simulation of the supersonic nozzle, Navier-Stokes equations are considered and as a turbulent model, $\kappa$-$\varepsilon$ /$\kappa$-$\omega$ blended SST two equation turbulent model is used. The characteristics of $\lambda$-shape shock systems due to the interaction of shock and boundary layer was investigated in a low NPR. And the result of comparison of thrust value shows that a fixed geometry nozzle can cover required flight mission.