• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.3
• /
• pp.205-212
• /
• 2021

In this study, two types of thrust stand modeling were proposed for the design of a thrust stand using flexure. Type A model generate combined load for tangential (thrust) and axial compressive load (self weight). And type B generate combined load for tangential and axial tensile load. The research was done by comparing the influence of the load between the models through a 1D calculation and computational analysis. The 1D calculated value and the computational analysis value were compared for a total of 10 sections and the results were confirmed to be very similar. In order to prove the validity of the analysis results, the equivalent stress was confirmed from the computational analysis of the flexure, and the production of the Type B model was selected from the evaluation of the yield condition (Von-Mises Yield Criterion).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.15-15
• /
• 2000

제트 베인에 의한 추력 방향 제어 장치는 롤 운동 제어를 가능하게 하고, 큰 선회 각도를 얻을 수 있는 장점이 있으나, 기계 장치가 비교적 복잡하고, 제트 베인의 열적, 구조적 문제를 해결하여야 한다. 복잡한 기계 장치는 유동 해석의 측면에서 고려해 볼 때 격자 형성을 어렵게 만들어 유동장 해석을 통한 성능예측을 어렵게 만든다. 구조물의 응력해석을 위하여 제트 베인 표면에서의 정압력과 더불어 마찰력도 고려하여야 하는데, 정확한 마찰력 계산을 위해서는 난류 모델링이 필수적이고, 그에 따라 벽면 근처에서 격자를 밀접시키는 것이 요구된다. 본 연구에서는 상용 유동해석 소프트웨어인 Fluent를 사용하여 제트 베인이 장착된 추력 방향 제어 장치의 3차원 난류 유동장 계산을 수행하였다. 피치, 요 운동의 경우와 롤 운동의 경우로 구분하여 계산하였으며, 최대 받음각을 $25^{\cire}$ 로 하여 제트 베인의 받음각에 따라 회전축에 작용하는 힘과 모멘트를 계산하였다. 본 연구의 결과는 향후 개발될 제트 베인이 장착된 추력 방향 제어 장치의 개념설계 단계에 필요한 기본자료로서 신뢰도를 높이는데 도움이 되리라 판단된다.

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.122-126
• /
• 2009

KSLV(Korea Space Launch Vehicle)-I is designed as a launch vehicle to enter a 100 kg-class satellite to the LEO(Low-Earth Orbit). Attitude angles of the upper-stage, including roll, pitch and yaw are controlled by cold gas thruster system using nitrogen gas. To verify the flow rate of the gas charging system and to prepare a nitrogen gas charging scenario, the development of a gas charging simulator for RCS(Reaction Control System) is required. This paper describes the orifice design, development, and test of the gas charging simulator for RCS of KSLV-I.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.189-199
• /
• 2013

This paper summarizes results of second stage attitude control of KSLV-I third flight test. The results show that three axes attitude control at coasting phases of KSLV-I was successfully accomplished by the reaction control system, and pitch and yaw attitude control at thrusting phase where second stage kick motor burns was also normally accomplished by using the thrust vector control system. It is verified that the second stage controller performed successfully for all flight phases regardless of some disturbances due to mass center offset, slag effects, and residual thrust of kick motor. These results may provide an important basis in enhancing domestic technology level of attitude control of launch vehicle.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.2 s.35
• /
• pp.39-43
• /
• 2006

The magnitude of the axial force acting on turbopump bearings has a great influence on the operational reliability and service life of a turbopump. In the turbopump under current investigation the cavity vanes are introduced to the pump shroud casing to control the axial thrust of the turbopump. To investigate the effect of the cavity vanes, 3D computational flow analyses for a propellant pump stage including an inducer, impeller, volute and secondary flow passages are performed with and without the vanes. The results show that the cavity vanes are very effective in reducing the magnitude of axial thrust without notable changes on the overall performance of the turbopump.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.4
• /
• pp.15-20
• /
• 2007

In order to control and balance axial thrust of turbo machine, many types of balancing devices are used but most of them are complicated and sometimes cause troubles. In this study, a very simple device of using shallow grooves mounted on a casing wall, known as "J-Groove", is proposed and studied experimentally and theoretically. The result shows that 70% of axial thrust in an industrial 4-stage centrifugal pump can be reduced at the best efficiency point. Moreover, the analytical method of "interfered gap flow" is established and a simple formula which can determine the optimum dimension of groove and its location is proposed.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.354-358
• /
• 2005

The magnitude of the axial force acting on turbopump bearings has a great influence on the operational reliability and service life of a turbopump. In the turbopump under current investigation the cavity vanes are introduced to the pump shroud casing to control the axial thrust of the turbopump. To investigate the effect of the cavity vanes, 3D computational flow analyses for a propellant pump stage including an inducer, impeller, volute and secondary flow passages are performed with and without the vanes. The results show that the cavity vanes are very effective in reducing the magnitude of axial thrust without notable changes on the overall performance of the turbopump.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.1
• /
• pp.36-40
• /
• 2012

The magnitude of the axial thrust acting on pump bearings has a great influence on the operational reliability and service life of a pump for turbopumps. In the present study, radial vanes are introduced to the pump casing to control the axial thrust by changing the cavity pressure between the impeller and the casing. To investigate the effect of the vanes on the axial thrust of the pump, experimental and computational studies were performed with and without the vanes. It is shown that the vanes reduce the cavity pressure by preventing the flow from rotating with the impeller. Experimental and computational results show similar trend for the axial thrust difference between two cases with and without the vanes. The results show that the cavity vanes are very effective in controlling the magnitude of the axial thrust.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.3 s.246
• /
• pp.230-237
• /
• 2006

Flows in the cavity with pump out vane are calculated using the CFX-Tascflow CFD code. flow calculations are performed for different values of vane height, numbers, leakage flow rate, and rotational speed. The flow is very complex and three dimensional with strong vortex and leakage flow over the vane. The variations of pressure coefficient and K-factor with these parameters and resulting effects on the thrust and torque are studied. The present study contributes to showing the capability of flow simulation of back cavity with pump-out vane. The calculated results are good enough to be used back cavity design.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.264-264
• /
• 2017