• Journal of KIISE:Information Networking
• /
• v.28 no.2
• /
• pp.229-235
• /
• 2001

With the explosive popularity of the World Wide Web, the low penonnance of network often leads web clients to wait a long time for web server's response. To resolve this problem, web caching (proxy) has been considered as the most efficient technique for web server to handle this problem. The placement of web proxy is critical to the overall penonnance, and Li et al. showed the optimal placement of proxies for a web server in the internet with the linear and tree topology when the number of proxies, ]M, is given [4, 5]. They focused on minimizing the over all access time. However, it is also considerable for target web server to minimize the total number of proxies while each proxy server guarantees not to exceed certain res(Xlnse time for each request from its clients. In this paper, we consider the problem of finding the optimal number and placement of web proxies with the lin~ar and tree topology under the given threshold cost for delay time.

• Journal of Korea Water Resources Association
• /
• v.35 no.5
• /
• pp.501-510
• /
• 2002

During drought or impending drought period, the reservoir operation method is required to incorporate demand-management policy rule. The objective of this study is focused to the development of demand reduction rule by incorporating hedging-effect for a single reservoir system. To improve the performance measure of the objective function and constraints, we could incorporate three risk performance criteria proposed by Hashimoto et al. (1982) by mixed-integer programming and also incorporate successive linear programming to overcome nonlinear hedging term from the previous study(Shih et al., 1994). To verify this model, this hedging rule was applied to the Daechung multi-purpose dam. As a result, we could evaluate optimal hedging parameters and monthly trigger volumes.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.2
• /
• pp.41-53
• /
• 2006

The brittle materials like rocks show complicated strain-softening behavior after the peak which is hard to model using the classical constitutive models based on the relation between strain and stress tensors. A kinematically constrained three-dimensional microplane constitutive model is developed for granite. The model is verified by fitting the experimented data of Westerly granite and Bonnet granite. The triaxial behavior of granite is well reproduced by the model as well as the uniaxial behavior. We studied the development of the fracture zone in granite during blasting impact using the model with the standard finite element method. All the results obtained from the microplane model developed are compared to those from the linear elasticity model which is commonly used in many researches and practices. It is found that the nonlinearity of rocks sigificantly affects the results of analysis.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.195-195
• /
• 2011

국가하천의 주변지역을 체계적이고 계획적으로 조성 이용하여 난개발을 방지하고 지속가능한 발전을 도모하며, 그에 따른 이익을 하천의 정비 및 관리 등에 활용함으로써 공공복리의 증진에 기여함을 목적으로 하는 친수구역활용에 관한 특별법이 곧 시행될 예정이다. 친수는 단순히 하천 보전과 상대되는 수변이용의 측면이 아니라 하천의 경관, 생태계, 물 등 전체적인 하천공간에서 이루어지는 인간의 활동과 심리적 만족감으로 해석할 수 있다. 이러한 친수활동 유형을 정립하기 위하여 전문가 및 실무자들의 도움으로 설문지를 작성하고, 조사하였다. 또한 평가 항목간의 중요도를 합리적으로 부여하고자 전문가 집단 활용을 통한 다기준의사결정 기법 중 계층분석과정 AHP(Analytic Hierarchy Process)와 이의 일반적인 형태인 ANP(Analytic Network Process) 기법을 이용하여 비교 분석하여 보았다. AHP는 의사결정의 목표 또는 평가기준이 다수이며 복합적인 경우, 다수의 속성들을 계층적으로 분류하여 각 속성의 중요도를 파악함으로써 최적 대안을 선정하는 기법으로 다수의 목표, 다수의 평가기준, 다수의 의사결정주체가 포함되어 있는 의사결정 문제를 계층화하여 해결한다. 그러나 의사결정 문제는 대부분 요소들 간의 수평적 상호작용과 수직종속성이 존재하기 때문에 단순히 계층적 구조만으로는 설명할 수 없는 경우가 있다. ANP는 AHP 분석을 확장한 개념으로 평가 요소가 계층구조를 가지고 있으면서 각 평가 요소간 네트워크 구조를 가지는 경우에 해당한다. 즉, 시스템 분석, 통합 및 조정을 위한 방법으로 요소들 간의 비선형 관계를 모델화하는 복잡한 의사결정에 적용이 가능하다. ANP는 AHP의 기본 공리인 독립성이 유지되지 않을 때도 적용할 수 있는 의사결정 방법이기 때문이다. AHP와 ANP 분석을 위해 평가기준은 하천특성, 생태환경특성, 인문환경특성, 경관, 유지관리 등으로 분류하였으며, 세부평가항목은 하천의 물리 생태학적 특성, 개발여건과 관련된 특성, 경관의 이용가치, 유지관리 용이성 등 20여 개로 나누었다. AHP와 ANP를 이용하여 친수공간 이용지수 가중치를 산정한 결과, 두 기법은 큰 차이를 보이지 않았다. 그러나 ANP를 이용하여 가중치를 결정하는 방법은 최종 결정의 공정성이나 신뢰성을 확보하는데 기여를 하는 것으로 나타났다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.5
• /
• pp.337-343
• /
• 2014

This paper presents a continuum-based shape design sensitivity analysis(DSA) method for crack propagation problems using a reproducing kernel method(RKM), which facilitates the remeshing problem required for finite element analysis(FEA) and provides the higher order shape functions by increasing the continuity of the kernel functions. A linear elasticity is considered to obtain the required stress field around the crack tip for the evaluation of J-integral. The sensitivity of displacement field and stress intensity factor(SIF) with respect to shape design variables are derived using a material derivative approach. For efficient computation of design sensitivity, an adjoint variable method is employed tather than the direct differentiation method. Through numerical examples, The mesh-free and the DSA methods show excellent agreement with finite difference results. The DSA results are further extended to a shape optimization of crack propagation problems to control the propagation path.

• Korean Chemical Engineering Research
• /
• v.53 no.2
• /
• pp.156-163
• /
• 2015

This paper presents a new framework for design and economic evaluation of wind energy-based electricity supply system. We propose a network optimization (mixed-integer linear programming) model to design the underlying energy supply system. In this model we include practical constraints such as land limitations of onshore wind farms and different costs of offshore wind farms to minimize the total annual cost. Based upon the model, we also analyze the sensitivity of the total annual cost on the change of key parameters such as available land for offshore wind farms, required area of a wind turbine and the unit price of wind turbines. We illustrate the applicability of the suggested model by applying to the problem of design of a wind turbines-based electricity supply problem in Jeju. As a result of this study, we identified the major cost-drivers and the regional cost distribution of the proposed system. We also comparatively analyzed the economic performance of on/off shore wind farms in wind energy-based electricity supply system of Jeju.

• Journal of Environmental Impact Assessment
• /
• v.29 no.6
• /
• pp.403-413
• /
• 2020

A mathematical model comprised with eight simultaneous quasi-linear partial differential equations was suggested to provide optimal chlorination strategy. Upstream weighted finite element method was employed to construct multidimensional numerical code. The code was verified against measured concentrations in three type of reactors. Boundary conditions and reaction rate were calibrated for the sixteen cases of experimental results to regenerate the measured values. Eight reaction rate coefficients were estimated from the modeling result. The reaction rate coefficients were expressed in terms of pH and temperature. Automatic optimal algorithm was invented to estimate the reaction rate coefficients by minimizing the sum of squares of the numerical errors and combined with the model. In order to minimize the concentration of chlorine and pollutants at the final usage sites, a real-time predictive control system is imperative which can predict the water quality variables from the chlorine disinfection process at the water purification plant to the customer by means of a model and operate the disinfection process according to the influent water quality. This model can be used to build such a system in water treatment plants.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.891-898
• /
• 2007

Optimal aerodynamic design for the pitch-controlled horizontal axis wind turbine and its aerodynamic performance for various pitch angles are performed numerically by using the blade element momentum theory. The numerical calculation includes effects such as Prandtl‘s tip loss, airfoil distribution, and wake rotation. Six different airfoils are distributed along the blade span, and the special airfoil i.e. airfoil of 40% thickness ratio is adopted at the hub side to have structural integrity. The nonlinear chord obtained from the optimal design procedure is linearized to decrease the weight and to increase the productivity with very little change of the aerodynamic performance. From the comparisons of the power, thrust, and torque coefficients with corresponding values of different pitch angles, the aerodynamic performance shows delicate changes for just $3^{\circ}$ increase or decrease of the pitch angle. For precisive pitch control, it requires the pitch control algorithm and its drive mechanism below $3^{\circ}$ increment of pitch angle. The maximum torque is generated when the speed ratio is smaller than the designed one.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.657-663
• /
• 2018

In this study, shape optimization was performed to improve the vibration isolation capability of an anti-vibration rubber assembly, which is used in the field option cabin of agricultural tractors. A uniaxial tension test and biaxial tension test were performed to characterize the hyper-elastic material properties of rubber, and the data were used to calibrate the material model used in the finite element analyses. A field test was performed to quantify the input excitation from the tractor and the output response at the cabin frame. To account for the nonlinear behavior of rubber, static analyses were performed and the load-displacement curve of rubber was derived. The stiffness of the rubber was calculated from this curve and input to the harmonic analyses of the cabin. The results were verified using the test data. Taguchi's parameter design method was used to find the optimal shape of the anti-vibration rubber assembly, which indicated a shape with reduced stiffness. The vibration of the cabin frame was reduced by the optimization by as much as 35% compared to the initial design.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.548-549
• /
• 2015

무인 잠수정은 자율 무인잠수정(이하 'AUV' 또는 '자율무인잠수정'을 혼용)과 원격조정잠수정(이하 'ROV'로 지칭)으로 분류를 할 수 있다. ROV는 테더 게이블로 인한 작업 범위의 한계와 운동성능 효율이 떨어지는 단점을 지니고 있어, 테더 케이블이 필요 없는 AUV에 대한 필요성이 증대되고 있다. 추측 항법 시스템인 관성 항법 시스템(inertial navigation system, 이하 'INS'로 지칭)은 외부 도움없이 관성측정 장치(inertial measurement unit, 이하 'IMU'로 지칭)를 활용하여 구성된 시스템을 말한다. IMU는 자이로 스코프(gyroscope), 가속도계(accelerometer), 지자기(magnetic)센서로 구성된 측정 장치로 3개의 센서를 사용하여 상호 보정을 통한 기동 체의 위치, 속도 및 자세 정보를 제공한다. 복합항법시스템은 추측항법시스템이 가지는 누적오차와 측위 항법시스템이 가지는 외부환경에 대한 단점을 상호 보완하는 방법으로 연구가 진행 중이다. 하지만 심해서 또는 해양의 특성에 따라 측위 시스템이 사용되지 못하기 때문에 추측 항법시스템의 다양한 관성 센서를 활용한 상로 보완과 신호처리 방법을 통한 연구 개발이 진행 중이다. 다양한 센서 정보를 통합하는 목적으로 칼만 필터와 같은 최적 필터기법이 보편적으로 사용되고 있다. 칼만 필터는 확률 선형 시스템에 대하여 공정잡음 및 측정 잡음이 가우시안 확률 분포를 따를 때 최적의 추정자가 된다. 또한 가우시안 조건을 만족하지 않는 경우에도 선형 추정자 중에 추정 오차의 분산이 가장 작은 추정자이다. 칼만 필터가 최상의 성능을 발휘 하려면 공정잡음과 측정 잡음의 실제 값을 정확히 알아내는 것이 중요하다. 잡음 수준에 대한 정보가 부정확 할 경우 칼만 필터는 발산 할 수 있기 때문에 시스템에서 잡음 수준의 공산은 칼만 필터의 최적 이득을 결정하는 중요한 요소로 추정치에 큰 영향을 준다. 따라서 칼만 필터를 추측항법시스템에 적용 시킬 경우 실제 모텔의 잡음 공분산을 정확히 추정할 수 있는 기법이 요구된다. 추측항법시스템은 다양한 센서를 활용하기 때문에 움직이는 기동 표적에 적용시 잡음공분상이 변하기 때문에 항법시스템이 저하 될 수 있다. 본 연구에서는 다양한 센서를 융합하여 해양 생체 로봇의 정밀 자세 제어가 가능한 시스템을 제안하고자 한다.