• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.3
• /
• pp.49-53
• /
• 2022

Ultra-thin glass (UTG) has been widely used in foldable display as a cover window for the protection of display and has a great potential for rollable display and various flexible electronics. The foldable display is under impact loading by bending and touch pen and exposed to other external impact loads such as drop while people are using it. These external impact loads can cause cracks or fracture to UTG because it is very thin under 100 ㎛ as well as brittle. Cracking and fracture lead to severe reliability problems for foldable smartphone. Thus, this study constructs finite element analysis (FEA) model for the pen drop test which can measure the impact resistance of UTG and conducts mechanical modeling to improve the reliability of UTG under impact loading. When a protective layer is placed to an upper layer or lower layer of UTG layer, stress mechanism which is applied to the UTG layer by pen drop is analyzed and an optimized structure is suggested for reliability improvement of UTG layer. Furthermore, maximum principal stress values applied at the UTG layer are analyzed according to pen drop height to obtain maximum pen drop height based on the strength of UTG.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.83.2-83.2
• /
• 2010

평판형 고체산화물 연료전지(planar SOFC : Solid oxide Fuelcell)는 높은 전류 효율 및 출력밀도를 가지는 중,대형 발전용 전기소자이다. SOFC 스택을 600~800도에서 작동할 경우, 금속 분리판에서 휘발된 크롬에 의한 열화현상과 금속의 산화에 의한 표면 저항의 증가가 큰 문제점으로 알려져 있으며, 이를 개선하기 위한 많은 연구가 진행되고 있다. 본 연구에서는 금속 분리판의 열화를 억제하기 위한 여러 보호코팅의 특성을 밝히고, 특성차이의 원인을 분석하고자 하였다. 모재는 상용 STS444합금 (Nisshin steel 생산) 2.0mmt 박판을 사용하였으며, 표면 상태를 균일하게 하기 위하여 표면은 동일한 #1200 번 사포로 연마후 코팅하였다. 적용한 코팅은 전기도금 Ni 코팅, (MnCo)3O4 wet powder spray 코팅, (MnCo)3O4 ADM코팅 3종이었으며, 코팅층의 두께는 최적 공정조건에 따라 달리 하였다. 산화후 형성되는 표면 산화물의 전기적 특성을 평가하기 위하여 시험편의 비면적 저항 (ASR : area specific resistance)을 장시간 측정하였다. 측정편의 크기는 가로 4cm ${\times}$ 세로 4cm였으며, 100시간 공기중 산화후 측정하였다. 표면 접촉을 높이기 위하여 Pt paste를 40~50um도포하였으며, 1~0.1A인가된 전류에 대한 저항을 4전극법 (4-probe)으로 측정하였다. 표면 코팅층이 크롬 휘발을 억제하는 정도를 평가하기 위하여 크롬 휘발량을 측정하였다. 시편은 가로 1.5cm ${\times}$ 세로 1cm 였으며, 공급된 공기와 수분의 혼합가스와 응축기 표면에 흡착된 크롬의 양을 ICP-MASS법으로 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.72-72
• /
• 2009

본 연구에서는 Photoconductor materials 기반의 평판형 X-ray Detector film 제작에 관한 연구를 수행하였다. 기존의 광도전성 물질로 사용되어 오던 비정질 셀레늄(Amorphous seleinum; a-Se) 기반의 디지털 방사선 검출기 보다 높은 신호 및 동작 특성을 가지는 Mercury Iodide(HgI2)와 열적, 전기적 특성이 안정적이며, 소자의 동작특성이 우수한 Lead Oxide(PbO) 기반의 X-ray Detector film의 개발에 있어서 각각 HgI2 및 PbO 두 물질 층을 적정비율에 맞추어 제작함으로써 최적의 X-ray Detector를 구현하고자 하였다. 이는 빠른 영상획득을 통해 기존의 방식이 가지는 문제점을 해결하고 의료기기 디지털화를 구현할 수 있는 차세대 시스템을 개발하고자 하는 것이다. 본 연구에서는 기존의 진공증착법의 두꺼운 대면적 필름의 제조가 어려운 문제점을 해결하고자 Particle In Binder method(PIB) 방법을 이용하여 $3"{\times}3"$사이즈의 두께 $200{\mu}m$의 다결정의 Photoconductor 필름을 제조하여 전기적 특성을 평가하였다. 제작된 필름의 전기적 특성을 dark current, X-선 sensitivity와 SNR(Signal to -Noise Rate) 등을 측정하여 정량적으로 평가 하였다. 기준 실험으로 진행한 DG 2.1 바인더를 사용한 single-HgI2 층에서 보다 높은 sensitivity 값을 보였지만 높은 dark current로 인해 SNR이 떨어지는 결과를 볼 수 있었다. 본 연구에서 제시하는 두 Photoconductor material의 Soaking method를 이용한 실험에서는 single-HgI2에 해당하는 높은 sensitivity 및 저감된 dark current로 인해 높은 SNR 값을 획득하였다. 하지만 습도와 같은 주변 환경에 의한 재현성 문제로 인한 신호값의 불안정성에 대한 문제점도 남아 있으므로, 차후 최적화된 material 제작 공정을 위한 연구가 꾸준히 진행 되어져야 할 것이다.

• Journal of Sensor Science and Technology
• /
• v.3 no.2
• /
• pp.16-23
• /
• 1994

Developed fiber-optic biosensor for the detection of organophosphorus compounds in a contaminated water needs the analysis of an enzyme kinetics and the transport phenomena in the reaction part to analyze the sensor signal and to design the sensor. The enzyme inhibition kinetics was investigated and the reactor model was proposed to design the reaction part in the proposed sensor. Since the acetylcholinesterase was inhibited by the organophosphorus compounds, experiments for enzyme inhibition reaction were performed from 0 to 2 ppm to be detected by the developed sensor, and irreversible enzyme inhibition kinetics was proposed. The reactor parts were divided into the two phases, i.e. bulk phase and immobilized enzyme layer, to analyze the flow and diffusion. Sensor signal was able to be analyzed based on the total reactor model established by linking the enzyme reaction kinetics. Based on the proposed model, the effects of loading enzyme amount and enzyme layer thickness on the magnitude of readout signal were simulated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.236-236
• /
• 2010

단일접합 $n^+-p/p^+$ (p-emitter) 및 $p^+-n/n^+$ (n-emitter) GaAs 태양전지 (Solar Cell)를 각각 제작하여, 그 소자특성을 비교 분석하였다. AM 1.5 (1 sun, $100\;mW/cm^2$) 표준광을 조사할 경우, p-emitter/n-emitter 소자의 개방회로전압 (Voc), 단락회로전류 (Jsc), 충전율 (FF), 효율 (Eff)은 각각 0.910/0.917 V, $15.9/16.1\;mA/cm^2$, 78.7/78.9, 11.4/12.1%로서, n-emitter 소자가 다소 크지만 거의 비슷한 값을 가지고 있었다. 태양전지의 집광 특성을 분석하기 위하여 조사광의 출력에 따른 태양전지의 소자 특성을 측정하였다. 조사광 강도가 높아짐에 따라 p-emitter 소자의 특성은 점진적으로 증가하는 반면, n-emitter는 1.3 sun에서 약 1.4 배의 최대 효율 (17%)을 나타내고 조사광이 더 증가함에 따라 급격히 감소하는 특성을 보여 주었다. (그림 참고) 본 연구에서 사용한 2종류 소자의 층구조는 서로 반대되는 대칭구조로서, 모두 가까이에 위치하고 있는 표면전극 (surface finger) 방향으로 소수전하 (minority carrier)가 이동하고 다수전하 (majority carrier)는 기판 (두께 $350\;{\mu}m$)을 통한 먼 거리의 후면전극 (back electrode)으로 표류 (drift)되도록 설계되어 있다. 이때, n-emitter에서는 이동도 (mobility)와 확산길이 (diffusion length)가 높은 전자가 후면전극으로 이동하기 때문에 적정밀도의 전자-정공 쌍 (EHP)이 여기될 경우에는 Jsc와 Eff가 극대화되지만, 조사광 강도 또는 EHP가 더 높아질 경우에는 직렬저항의 증가와 함께 전류-전압 (I-V)의 이상인자 (ideality factor)가 커짐으로서 FF와 효율이 급격히 감소한 결과로 분석된다. 현재 전산모사를 통한 자세한 분석을 진행하고 있으며, 본 결과는 효율 극대화를 위한 최적 층구조 및 도핑 밀도 설계에 활용할 수 있을 것으로 판단된다.

• Membrane Journal
• /
• v.33 no.6
• /
• pp.377-382
• /
• 2023

In this study, a PEBAX/PVDF composite membrane was fabricated, and its pervaporation performance was tested in an ethanol/water mixture. In addition, we attempted to improve the pervaporation performance of the composite membrane by forming a ZIF-8 layer on the surface of the PVDF substrate. The thickness of selective layer was optimized by comparing the pervaporation performance depending on the PEBAX thickness. A pervaporation test was performed on the Ethanol/Water mixture. As a result, the composite membrane using PVDF substrate with ZIF-8 layer had a flux of 1.98 kg/m²h and separation factor of 3.88, showing higher values of both permeation flux and selectivity than the composite membrane using bare PVDF substrate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.4
• /
• pp.437-445
• /
• 2015

A design method for a perforated panel is suggested to reduce the level of incident noise without obstructing the flow of incoming fluid. The key idea was to insert an array of 1/4 wavelength tubes around the holes of the perforate panel. First, various case studies were performed for a unit model with only one hole. In order to avoid any increase in the panel thickness, the unit model was vertically divided into three layers, and only the middle layer was used as the design domain. The number and array of 1/4 wavelength tubes connected to the hole were optimized to obtain the widest effective frequency range in the transmission loss curve as possible. Then, the optimally designed unit model was converted to a periodic array in the perforated panel to achieve the design goals. Even if the target frequency and the target transmission loss were set to 1000 Hz and 10 dB, respectively, the suggested design method for the a perforated panel could achieve noise reduction for various target values.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.1121-1124
• /
• 2015

In this paper, we propose and demonstrate an optimal design of wideband pulsed gamma-ray detectors. Pulsed gamma-ray detectors are designed to operate in a dose rate of $1{\times}10^6{\sim}1{\times}10^8rad(Si)/s$. The input parameter was derived based on the energy ratio of pulse gamma-ray spectrum and the time of the energy. The sensor output current was calculated based on the dose rate control circuit. Using the N-type Epi Wafer, the optimum condition detection sensor was designed based on TCAD. The simulation results show that the optimal Epi layer thickness is 45um when applied voltage 3.3V. The doping concentrations are as follows : N-type is an Arsenic as $1{\times}10^{19}/cm^3$, P-type is a Boron as $1{\times}10^{19}/cm^3$ and Epi layer is Phosphorus as $3.4{\times}10^{12}/cm^3$. Pulse gamma-ray detector diameter is the 1.3mm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.8
• /
• pp.13-19
• /
• 2001

We report on the fabrication and characterization of $Al_{0.3}Ga_{0.7}N$ HFETs with different barrier layer thickness which were grown using plasma-assisted molecular beam epitaxy (PAMBE). The barrier thickness of $Al_{0.3}Ga_{0.7}N$/GaN HFETs could be optimized in order to maximize 2 dimensional electron gas induced by piezoelectric effect without the relaxation of $Al_{0.3}Ga_{0.7}N$ layer. $Al_{0.3}Ga_{0.7}N$/GaN (20 nm/2 mm) HFET with 0.6 ${\mu}m$-long and 34 ${\mu}m$-wide gate shows saturated current density ($V_{gs}=1\;V$) of 1.155 A/mm and transconductance of 250 ms/mm, respectively. From high frequency measurement, the fabricated $Al_{0.3}Ga_{0.7}N$/GaN HFETs showed $F_t=13$ GHz and $F_{max}=48$ GHz, respectively. The uniformity of less than 5% could be obtained over the 2 inch wafer. In addition to the optimization of epi-layer structure, the relation between breakdown voltage and high frequency characteristics has been examined.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.291-298
• /
• 2020

ZITO/Ag/ZITO multilayer transparent electrodes at room temperature on glass substrates were prepared using RF/DC magnetron sputtering. Transparent conductive films with a sheet resistance of 9.4 Ω/㎡ and a transmittance of 83.2% at 550 nm were obtained for the multilayer structure comprising ZITO/Ag/ZITO (100/8/42 nm). The sheet resistance and transmittance of ZITO/Ag/ZITO multilayer films meant that they would be highly applicable for use in polymer-dispersed liquid crystal (PDLC)-based smart windows due to the ability to effectively block infrared rays (heat rays) and thereby act as an energy-saving smart glass. Effects of the thickness of the PDLC layer and the intensity of ultraviolet light (UV) on electro-optical properties, photopolymerization kinetics, and morphologies of difunctional urethane acrylate-based PDLC systems were investigated using new transparent conducting electrodes. A PDLC cell photo-cured using UV at an intensity of 2.0 mW/c㎡ with a 15 ㎛-thick PDLC layer showed outstanding off-state opacity, good on-state transmittance, and favorable driving voltage. Also, the PDLC-based smart window optimized in this study formed liquid crystal droplets with a favorable microstructure, having an average size range of 2~5 ㎛ for scattering light efficiently, which could contribute to its superior final performance.