• Journal of the Korean Wood Science and Technology
• /
• v.13 no.1
• /
• pp.19-62
• /
• 1985

This study was performed to investigate: (i) the bending processing properties of silk worm oak (Quercus acutissima Carr.) and Korean red pine (Pinus densiflora S. et Z.) by boiling and steaming treatments; (ii) the effects of interrelated factors - sapwood and heartwood, annual ring placement, softening temperature and time, moisture content. and wood defects on bending processing properties; (iii) the changing rates of bending radii after release from a tension strap, and (iv) the improving methods of bending process by treatment with chemicals. The size of specimens tested was $15{\times}15{\times}350mm$ for boiling and steaming treatments and $5{\times}10{\times}200mm$ for treatments with chemicals. The specimens were green for boiling treatments and dried to 15 percent for steaming treatments. The specimens for treatments with chemicals were soaked in saturated urea solution, 35 percent formaldehyde solution, 25 percent polyethylene glycol -400 solution, and 25 percent ammonium hydroxide solution for 5 days and immediately followed the bending process, respectively. The results obtained were as follows: 1. The internal temperature of silk worm oak and Korean red pine by boiling and steaming time was raised slowly to $30^{\circ}C$ but rapidly from $30^{\circ}C$ to $80-90^{\circ}C$ and then slowly from $80-90^{\circ}C$ to $100^{\circ}C$. 2. The softening time required to the final temperature was directly proportional to the thickness of specimen. The time required from $25^{\circ}C$ to $100^{\circ}C$ for 15mm-squared specimen was 9.6-11.2 minutes in silk worm oak and 7.6-8.1 minutes in Korean red pine. 3. The moisture content (M.C.) of specimen by steaming time was increased rapidly first 4 minutes in the both species, and moderately from 4 to 20 minutes and then slowly and constantly in silk worm oak, and moderately from 4 to 15 minutes and then slowly and constantly in Korean red pine. The M.C. of 15mm-squared specimen in 50 minutes of steaming was increased to 18.0 percent in the oak and 22.4 percent in the pine from the initial conditioned M.C. of 15 percent The rate of moisture adsorption measured was therefore faster in the pine than in the oak. 4. The mechanical properties of the both species were decreased significantly with the increase of boiling rime. The decrement by the boiling treatment for 60 minutes was measured to 36.6-45.0 percent in compressive strength, 12.5-17.5 percent in tensile strength, 31.6-40.9 percent in modulus of rupture, and 23.3-34.6 percent in modulus of elasticity. 5. The minimum bending radius (M.B.R.) of sapwood and heartwood was 60-80 mm and 90 mm in silk worm oak, and 260 - 300 mm and 280 - 300 mm in Korean red pine, respectively. Therefore, the both species showed better bending processing properties in sapwood than in heartwood. 6. The M.B.R. of edge-grained and flat-grained specimen in suk worm oak was 60-80 mm, but the M.B.R. in Korean red pine was 240-280 mm and 260-360 mm, respectively. Comparing the M.B.R. of edge-grained with flat-grained specimen, in the pine the edge-grained showed better bending processing property than the flat-grained. 7. The bending processing properties of the both species were improved by the rising of softening temperature from $40^{\circ}C$ to $100^{\circ}C$. The minimum softening temperature for bending was $90^{\circ}C$ in silk worm oak and $80^{\circ}C$ in Korean red pine, and the dependency of softening temperature for bending was therefore higher in the oak than in the pine. 8. The bending processing properties of the both species were improved by the increase of softening time as well as temperature, but even after the internal temperature of specimen reaching to the final temperature, somewhat prolonged softening was required to obtain the best plastic conditions. The minimum softening time for bending of 15 mm-squared silk worm oak and Korean red pine specimen was 15 and 10 minutes in the boiling treatment, and 30 and 20 minutes in the steaming treatment, respectively. 9. The optimum M.C. for bending of silk worm oak was 20 percent, and the M.C. above fiber saturation point rather degraded the bending processing property, whereas the optimum M.C. of Korean red pine needed to be above 30 percent. 10. The bending works in the optimum conditions obtained as seen in Table 24 showed that the M.B.R. of silk worm oak and Korean red pine was 80 mm and 240 mm in the boiling treatment, and 50 mm and 280 mm in the steaming treatment, respectively. Therefore, the bending processing property of the oak was better in the steaming than in the boiling treatment, but that of the pine better in the boiling than in the steaming treatment. 11. In the bending without a tension strap, the radio r/t of the minimum bending radius t to the thickness t of silk worm oak and Korean red pine specimen amounted to 16.0 and 21.3 in the boiling treatment, and 17.3 and 24.0 in the steaming treatment, respectively. But in the bending with a tension strap, the r/t of the oak and the pine specimen decreased to 5.3 and 16.0 in t he boiling treatment, and 3.3 and 18.7 in the steaming treatment, respectively. Therefore, the bending processing properties of the both species were significantly improved by the strap. 12. The effect of pin knot on the degradation of bending processing property was very severe in silk worm oak by side, e.g. 90 percent of the oak specimens with pin knot on the concave side were ruptured when bent to a 100 mm radius but only 10 percent of the other specimens with pin knot on the convex side were ruptured. 13. The changing rate in the bending radius of specimen bent to a 300 mm radius after 30 days of exposure to room temperature conditions was measured to 4.0-10.3 percent in the boiling treatment and 13,0-15.0 percent in the steaming treatment. Therefore, the degree of spring back after release was higher in the steaming than in the boiling treatment. And the changing rate of moisture-proofing treated specimen by expoxy resin coating was only -1.0.0 percent. 14. Formaldehyde, 35 percent solution, and 25 percent polyethylene glycol-400 solution found no effect on the plasticization of the both species, but saturated urea solution and 25 percent ammonium hydroxide solution found significant effect in comparison to non-treated specimen. But the effect of the treatment with chemicals alone was inferior to that of the steaming treatment, and the steaming treatment after the treatment with chemicals improved 10-24 percent over the bending processing property of steam-bent specimen. 15. Three plasticity coefficients - load-strain coefficient, strain coefficient, and energy coefficient - were evaluated to be appropriate for the index of bending processing property because the coefficients had highly significant correlation with the bending radius. The fitness of the coefficients as the index was good at load-strain coefficient, energy coefficient, and strain coefficient, in order.

• Journal of Intelligence and Information Systems
• /
• v.23 no.1
• /
• pp.47-67
• /
• 2017

Steel plate faults is one of important factors to affect the quality and price of the steel plates. So far many steelmakers generally have used visual inspection method that could be based on an inspector's intuition or experience. Specifically, the inspector checks the steel plate faults by looking the surface of the steel plates. However, the accuracy of this method is critically low that it can cause errors above 30% in judgment. Therefore, accurate steel plate faults diagnosis system has been continuously required in the industry. In order to meet the needs, this study proposed a new steel plate faults diagnosis system using Simultaneous MTS (S-MTS), which is an advanced Mahalanobis Taguchi System (MTS) algorithm, to classify various surface defects of the steel plates. MTS has generally been used to solve binary classification problems in various fields, but MTS was not used for multiclass classification due to its low accuracy. The reason is that only one mahalanobis space is established in the MTS. In contrast, S-MTS is suitable for multi-class classification. That is, S-MTS establishes individual mahalanobis space for each class. 'Simultaneous' implies comparing mahalanobis distances at the same time. The proposed steel plate faults diagnosis system was developed in four main stages. In the first stage, after various reference groups and related variables are defined, data of the steel plate faults is collected and used to establish the individual mahalanobis space per the reference groups and construct the full measurement scale. In the second stage, the mahalanobis distances of test groups is calculated based on the established mahalanobis spaces of the reference groups. Then, appropriateness of the spaces is verified by examining the separability of the mahalanobis diatances. In the third stage, orthogonal arrays and Signal-to-Noise (SN) ratio of dynamic type are applied for variable optimization. Also, Overall SN ratio gain is derived from the SN ratio and SN ratio gain. If the derived overall SN ratio gain is negative, it means that the variable should be removed. However, the variable with the positive gain may be considered as worth keeping. Finally, in the fourth stage, the measurement scale that is composed of selected useful variables is reconstructed. Next, an experimental test should be implemented to verify the ability of multi-class classification and thus the accuracy of the classification is acquired. If the accuracy is acceptable, this diagnosis system can be used for future applications. Also, this study compared the accuracy of the proposed steel plate faults diagnosis system with that of other popular classification algorithms including Decision Tree, Multi Perception Neural Network (MLPNN), Logistic Regression (LR), Support Vector Machine (SVM), Tree Bagger Random Forest, Grid Search (GS), Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). The steel plates faults dataset used in the study is taken from the University of California at Irvine (UCI) machine learning repository. As a result, the proposed steel plate faults diagnosis system based on S-MTS shows 90.79% of classification accuracy. The accuracy of the proposed diagnosis system is 6-27% higher than MLPNN, LR, GS, GA and PSO. Based on the fact that the accuracy of commercial systems is only about 75-80%, it means that the proposed system has enough classification performance to be applied in the industry. In addition, the proposed system can reduce the number of measurement sensors that are installed in the fields because of variable optimization process. These results show that the proposed system not only can have a good ability on the steel plate faults diagnosis but also reduce operation and maintenance cost. For our future work, it will be applied in the fields to validate actual effectiveness of the proposed system and plan to improve the accuracy based on the results.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.54 no.1
• /
• pp.124-133
• /
• 2009

Demand for the high quality barley with fibroid material and functional substances has been increasing in recent although the amount of barley consumption decreased drastically during the last two decades. But the limited information on quality of barley makes consumers hard when they purchase barley for their own consumption. Therefore, 51 brand barley, .i.e., 28 naked barley and 23 waxy barley from supermarkets and 10 polished barley from local markets were collected, and their external quality were analyzed to provide basic information on brand barley. Among 51 brand barley, 56% were 1kg package and 25% were 800 g package and there was no significant difference ($1{\pm}3.62\;g$) between printed and actual weighs. The weight of 1,000 grains of naked barley and waxy barley ranged $18.6{\sim}26.7\;g$ and $14.6{\sim}24.7\;g$, respectively. Thousand grain weight of 38% of naked barley ranged $20{\sim}22\;g$, while that of 43% of waxy barley ranged $18{\sim}20\;g$. The ratio of normal grains was 88% and 94% for naked barley and waxy barley, respectively, when separated with 1.7 mm sieve. Although 82% of brand barley products were free from foreign substances, in 18% of brand barley products, sands, pieces of cloth and wood, other kinds of grain and insect larvae were found, Average test weight of brand barleys was $843g{\cdot}L^{-1}$ with range of $805{\sim}917g{\cdot}L^{-1}$. Water content was less than 14% in 7.8% of barley products, while it was $14{\sim}15%$ in 62.7% of them. Average whiteness of brand barley was 31.06, while waxy barley had higher whiteness with 27.28 than naked barley with 34.16. Heated water uptake rate of milled naked barley and milled waxy barley were 215.4% and 231.7%, respectively, while expansion rate of milled naked barley and milled waxy barley were 379.7% and 401.6%, respectively. Barley from local markets were as good as brand barley products in 1,000 grain weight, ratio of normal grains, inclusion of foreign substances, test weight, water content, whiteness, water uptake rate, and expansion rate, but they showed higher ratio of foreign substances included.

• Journal of Animal Science and Technology
• /
• v.45 no.1
• /
• pp.69-78
• /
• 2003

This experiment was carried out to evaluate the value of total mixed fermentation feeds(TMFF) as completely mixed ration and to observe the effect of various kinds of TMFF on the palatability, feed intake, and milk performance in Holstein cows. The dry matter (DM) content of TMFF used in the experiment was 23.98-28.42% range, and CP, TDN, ADF and NDF were 16.2${\sim}$19.2%, 58.3-65.1%, 34.4-39.6% and 46.9${\sim}$49.9% levels, respectively. The relative feed value (RFV) in rape-, alfalfa-, grass-, oat-, corn-TMFF groups were 138.6, 133.9, 116.5, 111.8, 111.4 and 108.1, respectively. Among these groups, RFV of rye-TMFF group was lowest. Dry matter disappearance(DMD) showed 0.8${\sim}$.9% to the all kinds of TMFF groups. The pH was 3.89${\sim}$.87 and $NH_3$-N concentration was 6.93-8.66 mg/$d\ell$. The acetic acid concentration in the raw material of TMFF showed low level of 0.19${\sim}$0.57%, lactic acid showed high level of 1.17${\sim}$3.21% and butyric acid was very high as 0.03${\sim}$0.32%. Therefore, these results provide evidence that the quality of TMFF was not so bad. In the daily fresh matter intake on the alfalfa-, grass-, rape-, corn-, oats- and rye-TMFF were showed 62.85, 60.48, 58.04, 57.11, 54.61 and 45.74 kg respectively. All TMFF showed high palatability as daily dry matter intake of 1.95 to 2.90% by body weight of experimental cows. Body condition score(BCS) was gradually increased in during 60 days of the experiment term. Average daily gain(ADG) showed about 140.0${\sim}$326.7g. In alfalfa-TMFF group, the ADG was higher than in the other groups (p<0.05). Also, the increase in BCS was observed in grass-TMFF group (3.07 to 3.34) and rye-TMFF group was decreased in 3.07 to 3.34 (p<0.05). The milk yield appropriately showed a range of 16.16${\sim}$18.95 kg in all groups. Among these groups, alfalfa-TMFF group was highest(P<0.05). Average milk fat contents showed high levels of 4.06${\sim}$4.79% and the level was high in order of rape-, grass-, corn-, alfalfa-, rye- and oats-TMFF. Milk protein was highest in forage-TMFF and level of lactose in milk was approximately 4.56% in overall groups. Solid non fat(SNF) and total solid(TS) contents were 8.75% and 12.8%, respectively. However, milk composition was not significantly affected by TMFF.