• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.145.2-145.2
• /
• 2014

최근 반도체 산업의 급속한 발전으로 반도체 생산 설비 시설 또한 꾸준히 증설되어가는 추세이다. 이에 따라 반도체 산업의 핵심기술로 부각되고 있는 진공 기술은 다양한 응용목적을 위한 진공시스템 설계와 운영을 필요로 한다. 진공시스템의 알맞은 설계는 시스템 구성에 따른 진공특성을 예측하는 것이 중요하며 목적에 부합한 진공펌프를 선택하고 운영하여 최소비용으로 시스템 활용효율성을 극대화할 수 있는 설계를 해야 한다. 또한 공정의 저전력, 대유량화 추세에 따라 고유량 영역의 드라이펌프 부하 내구성 대응 요구에 부응하는 객관적 내구성평가의 정립 및 표준 측정 시험평가 방법의 필요성이 점차 대두되고 있는 경향에 있다. 본 연구에서는 드라이펌프의 공정현장 적응능력 평가를 위하여 최소 1시간에서 3시간동안 압력별 가스부하에 따른 드라이펌프의 실시간 특성을 관찰하였다. 실험은 1 mbar에서 최대 300 mbar까지의 연속적인 부하 조건에서 유량, 진동, 소음, 소비전력과 Sudden Vent Test를 실시간으로 측정하였고 드라이펌프의 특성 분석은 각 용량별 압력에 따른 유량, DP BP 소비전력, 소음, 진동, DP Body Temperature 등의 데이터를 Type에 따라 비교 분석하였다. 이에 부응하는 평가 장치 구축 및 데이터분석은 한국표준과학연구원 진공펌프 평가실험실에서 수행되었다.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2022.05a
• /
• pp.712-714
• /
• 2022

스테레오 정합을 통해 산출되는 초기 시차 영상의 정합 정확도는 고주파 및 잡음 성분에 의해 감소될 수 있다. 또한, 폐색 및 질감이 없는 영역에서 잘못된 정합 결과가 산출됨으로 인해 정합 정확도가 감소될 수 있다. 정합 정확도를 향상시키기 위해 시차 정제에 관한 선행 연구들이 수행되었지만 정제 과정을 통한 정합 정확도 성능과 처리 속도간 트레이드-오프가 존재한다. 이에 본 논문에서는 종래 시차 정제 방법 대비 향상된 처리 속도와 함께 높은 시차 정제 성능을 갖는 분리형 중앙-최댓값 필터를 제안한다. 제안하는 방법의 정제 성능 및 평균 처리 시간을 객관적으로 평가하기 위해 KITTI 2015 stereo benchmark 데이터셋을 사용하였다. 제안하는 방법의 평균 오차율은 비폐색 및 폐색 조건에서 종래 방법 대비 각각 최소 25.61% 및 23.68% 감소되었다. 또한, 제안하는 방법의 처리 속도는 종래 방법 대비 최소 13.29% 향상되었다. 따라서 제안하는 방법은 빠른 처리 속도 및 높은 정확도 성능을 요구하는 스테레오 비전 시스템에 활용될 수 있다.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2010.04a
• /
• pp.43-43
• /
• 2010

국내에 천연가스버스가 보급된 이래 5차례의 용기파열 사고가 발생하였는데 그중 2005년 8월 전주 덕진충전소에서 발생한 용기파열사고는 CNG용기의 라이너를 감싸고 있는 복합재료가 손상되어 발생한 사고로 보고되었다. 복합재료용기의 외피손상이 원인이 되어 발생한 사고사례는 해외에서 약 13건이 보고되었다. CNG용기 외피손상은 용기룰 고정하는 스트랩과 밀접한 관련이 있다. 용기고정이 불완전하면 슬립이 발생하고 이는 복합재의 손상으로 이어진다. 본 연구에서는 ISO 19078, CGA C6.4 등 국제코드의 규정을 고려하여 국내에서 제조된 Type 2, 3, 4 용기와 외국에서 생산된 Type 3 용기를 대상으로 결함깊이, 길이, 넓이에 따른 복합재료 결함 내구성시험을 수행하여 CNG용기의 내구성능을 평가하였고, 시험과 동일한 조건으로 복합재료 손상결함 조건을 컴퓨터로 전산모사하여 시험결과의 타당성과 유효성을 비교 검증하였다. 실험결과, Type 2 용기의 경우, 11,250회의 최소반복가압 회수를 충족하였으나 외피손상부와 반복가압에 따른 실제누출부위가 일치하지 않아 실험조건을 달리한 추가실험이 요구되었다. Type 3 용기의 경우에는 복합재 결함부위와 누수부위가 일치된 시험용기의 수는 67%정도로, 복합재료 용기의 수명을 저하시키는 원인으로 라이너와 외피손상이 서로 밀접한 관련이 있음을 확인하였다. Type 4 용기는 국제기준에서 요구하는 반복횟수를 만족하였고, 손상깊이 0.75mm와 1.25mm에서 반복가압회수가 60,000회 이상이 되어도 누설이 발생되지 않았다. 이는 라이너의 재질이 폴리머로서 균일한데다 탄소섬유 복합재료층 위에 유리섬유 복합재료 층이 1.5mm 정도 추가로 적층되어 있어서 3등급의 손상결함(결함깊이 1.25mm)에서도 구조 층이 전혀 손상되지 않은 것으로 판단되며, 이는 Type 2 용기의 강재라이너나 Type 3의 알루미늄 라이너와 비교하여 Type 4 용기의 폴리에틸렌 라이너의 물성이 반복성능이 탁월함을 확인할 수 있었다.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.11
• /
• pp.5-10
• /
• 2020

Although pile driver overturning accidents at construction site are not frequent, most leads to serious disasters. The main cause of accidents is uneven settlement of the ground. To prevent this, related guidelines such as KOSHA-C-101-2014, KOSH-A-GUIDE-71-2012, Occupational Safety and Health Standards, and NCS stipulate the installation of steel plates over ground. However, since the required steel plate thickness considering the self-weight of pile drivers and the underlying ground condition is not quantitatively presented, it is randomly applied in the field. In this study, the required minimum steel plate thickness was analyzed based on a numerical analysis (Plaxis 2D). Settlements and soil failure were calculated according to the different type of soils (sand, clay), load distribution and steel plate thickness (10mm, 20mm, 30mm, 40mm). Under all conditions, 10mm steel plate causes soil collapse. From thickness 20mm, the ground uneven subsidence is within 2° of the allowable leader angle.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.173-181
• /
• 2013

This paper proposes a heuristic optimal solution of multicommodity transportation problem. The proposed algorithm has 3 steps. First the proposed algorithm transforms multicommodity transshipment problem to a general transportation problem, but if the problem is a multicommodity transportation problem, it is not transformed. And the multicommodity is disassembled to a single commodity. Second if it is a multicommodity transportation problem, the algorithm selects the minimum cost according to commodity, on the other hand if it is a multicommodity transshipment problem, the algorithm directly selects the minimum cost based on demand area. And the algorithm assigns carloadings to be satisfied the supply and demand quantity. The algorithm repeats these processes until a given demand quantity is satisfied. Last if it has a condition that is able to reduce the transportation expense, the proposed algorithm controls the assignment quantity of the initial value that got from the step 2. The proposed algorithm was applied to two multicommodity transportation problem and three multicommodity transshipment problem and it got more good result than an existing linear programming method.

• Water for future
• /
• v.29 no.3
• /
• pp.197-205
• /
• 1996

Flow carrying capacity of water distribution systems is getting reduced by deterioration of pipes in the systems. The objective of this study is to develop a managerial decision-making model for the rehabilitation of water distribution systems with a minimum cost. The decisions made by the model also satisfy the requirements for the discharge and pressure at demanding nodes in the system. The replacement cost, pipe break repair cost, and pumping cost are considered in the economic evaluation of the decision along with the break ratio and interest ratio to determine the optimal replacement time for each pipe. Then, the hydraulic integrity of the water distribution system is checked for the decision by a pipe network simulator, KYPIPE, if the discharge and pressure requirements, the decision made for the optimal replacement time is revised until the requirements are satisfied. The model is applied to an existing water distribution system, the Metropolita Water Supply Project (1st Phase). The result shows that the decisions for the replacement time determined by the economix analysis are accepted as optimal and the hydraulic integrity of the system is in good condition.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.1
• /
• pp.23-34
• /
• 2004

This paper presents architecture and control method of packet scheduler to guarantee QoS of high quality streaming services in high-speed packet-switched networks. Since streaming services need far more stringent QoS requirements than the typical sort of burst data applications, they should be guaranteed minimum bandwidth and end-to-end delay bound to each flow, regardless of the behavior of other flows. To meet these requirements, a packet scheduler isolate a flow from the undesirable effects of other flows and provides end-to-end delay guarantees for individual flow and divides stringently the available link bandwidth among flows sharing the link. Until now, many vendors are developing traffic management chips running at 10Gbps, but most of chips have drawbacks to support high quality streaming services. In this paper, we investigate the drawbacks of commercial TM chips and traffic characteristic of streaming services and present implementation frameworks of the proposed packet scheduler. Finally, we analyze the simulation results of the proposed scheduler.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.10
• /
• pp.493-501
• /
• 2007

The imprecise real-time system provides flexibility in scheduling time-critical tasks. Most scheduling problems of satisfying both 0/1 constraint and timing constraints, while the total error is minimized, are NP-complete when the optional tasks have arbitrary processing times. Liu suggested a reasonable strategy of scheduling tasks with the 0/1 constraint on uniprocessors for minimizing the total error. Song et at suggested a reasonable strategy of scheduling tasks with the 0/1 constraint on multiprocessors for minimizing the total error. But, these algorithms are all off-line algorithms. In the online scheduling, the NORA algorithm can find a schedule with the minimum total error for the imprecise online task system. In NORA algorithm, EDF strategy is adopted in the optional scheduling. On the other hand, for the task system with 0/1 constraint, EDF_Scheduling may not be optimal in the sense that the total error is minimized. Furthermore, when the optional tasks are scheduled in the ascending order of their required processing times, NORA algorithm which EDF strategy is adopted may not produce minimum total error. Therefore, in this paper, an online algorithm is proposed to minimize total error for the imprecise task system with 0/1 constraint. Then, to compare the performance between the proposed algorithm and NORA algorithm, a series of experiments are performed. As a conseqence of the performance comparison between two algorithms, it has been concluded that the proposed algorithm can produce similar total error to NORA algorithm when the optional tasks are scheduled in the random order of their required processing times but, the proposed algorithm can produce less total error than NORA algorithm especially when the optional tasks are scheduled in the ascending order of their required processing times.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.12
• /
• pp.2219-2225
• /
• 2016

Mobile communication systems should be able to support multimedia traffics with limited transmit power due to the frequency reuse for maximizing the channel accommodation. Real-time data is very sensitive to delay, and they need to be transmitted instantly. On the other hand, non-real time data is less sensitive to delay, and their packet loss can be handled more flexibly. Therefore an adaptive resource management scheme is essentially required which enables to keep the minimal power allocated in the base station while guaranteeing the user requirements for QoE within a permissible range. Power-saving techniques are required in order to support multimedia services in the mobile networks because the power consumption increases greatly with the transmission rate increase. This paper proposes a novel scheme which enables to keep the allocated power minimal while guaranteeing the user requirements for QoE within a permissible range.

• Journal of Korean Society of Transportation
• /
• v.22 no.4 s.75
• /
• pp.43-56
• /
• 2004

The KHCM procedure is a micro level analysis at signalized intersections requiring a lot of input variables and complex computations. The research was to investigate the possibility of simplifying the analysis procedures by using the generalized or the combined variables that less influence on the adjusted traffic volume and through-car equivalents of left or right turns. It was also tried to make lane grouping into directional flow ratio(v/s) based on a field surveys. The maximum and minimum values of each variables were compared with each other through the KHCM analysis procedures in terms of control delay. The lane grouping and the synthetical influence of a simplified method was evaluated with the scenario built in prevailing maximum and minimum conditions. The study showed that the control delay was not significantly sensitive to the selected variables and the lane grouping and their synthetical influence as well.