• Clean Technology
• /
• v.19 no.2
• /
• pp.128-133
• /
• 2013

Catalytic combustion of benzene over $CeO_2$-supported copper oxides has been investigated. The supported copper oxides catalysts were prepared using ball mill method and characterized by XRD, FT-IR, TEM and TPR. In the CuO/$CeO_2$ catalysts prepared using ball mill method, highly dispersed copper oxide species were shown at high loading ratio. The CuO/$CeO_2$ prepared using ball mill method showed the higher activity than those prepared using impregnation method. The catalytic activity increased with an increase in the CuO loading ratio, 10 wt% loaded CuO/$CeO_2$ catalyst giving the highest activity. In addition, the promoting of 10 wt% loaded CuO/$CeO_2$ catalyst with $Fe_2O_3$ and CoO enhanced the dispersion of CuO and then increased the catalytic activity.

• Korean Chemical Engineering Research
• /
• v.51 no.3
• /
• pp.364-369
• /
• 2013

Oxidative dehydrogenation of n-butane over mesoporous Cr catalysts were studied. Catalysts were prepared by Cr impregnated method over Ti or Zr dispersed mesoporous support such as SBA-15, ${\gamma}$-alumina and characterized by XRD, SEM, TEM, FT-IR UV-Vis and ICP-AES. The effect of high surface area was not noticed appreciably in terms of conversion, but for Cr catalysts with Ti and Zr-incorporated on SBA-15 and ${\gamma}$-alumina. showed high selectivity of trans-2-butene.

• Applied Chemistry for Engineering
• /
• v.34 no.6
• /
• pp.584-589
• /
• 2023

The physicochemical properties of VOx/TiO₂ catalysts with different TiO₂ supports were analyzed, and SCR reactions were performed. VOx/TiO₂ catalysts were prepared by impregnation using anatase TiO₂, which was manufactured by Sigma Aldrich and prepared from TiOCl₂ and titanium isopropoxide (TTIP) as a precursor. They are denoted as VS, VC, and VP. The specific surface area of the VS was 1/10 or less of that of the VC and VP, and the dispersibility of vanadium oxide was relatively low. As a result of XPS analysis, the ratio of adsorbed oxygen was higher in VS and VP with Ti³⁺ than in VC. In VC and VP, vanadium mainly existed in V⁴⁺ and V³⁺ states in relation to the dispersibility of vanadium oxide. The amount of adsorbed oxygen contributed more to NH₃-SCR activity than vanadium oxide dispersibility below 250 ℃, while vanadium oxide dispersibility contributed more to activity beyond 300 ℃. The fast SCR activity in all three samples was the highest at NO₂/NOx = 0.5, followed by VS < VC < VP samples. It was determined that the dispersibility of vanadium oxide had a significant effect on fast NH₃-SCR activity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.97-97
• /
• 2015

전 세계적으로 화석연료의 고갈 및 환경오염 문제를 해결하기 위해 신재생에너지에 대한 관심이 급증하고 있다. 이러한 신재생에너지에는 수소 에너지, 자연 에너지(태양열, 지열 등), 바이오 매스 에너지 등이 포함된다. 이 중 수소 에너지는 지구상에 풍부하게 존재하고 있는 물과 탄화수소로부터 얻어지며, 연소 시에도 다시 물을 형성하여 오염 물질을 배출하지 않는 차세대 무공해 에너지원으로써 주목을 받고 있다. 수소 제조를 위한 공정에는 수증기 개질 공정(steam reforming), 부분 산화(partial oxidation) 및 자열개질(autothermal reforming) 등이 있으며 실제로 생산되는 대부분의 수소는 탄소/수소비(1:4)가 높은 메탄($CH_4$) 가스를 이용한 메탄 수증기 개질 공정(steam methane reforming)을 통하여 제조된다. 이 때 수소 제조의 고효율화 및 저비용화를 위해서는 반응물에 대한 높은 선택도, 고활성도 및 높은 안정성을 갖는 촉매가 반드시 필요하며, 대표적으로 Ni, Pt, Ru 등이 보고되고 있다. 이러한 촉매들은 대부분 세라믹 pellet 형태로 제작되어 왔으나 열전도도가 낮고 물리적 충격에 취약하다는 단점이 존재한다. 따라서 우리는 이러한 단점을 극복하고, 촉매의 활성을 높이기 위하여 다공성 금속 합금 폼을 촉매 지지체로 도입하였다. 또한, 다공성 금속 합금 폼 표면에 촉매의 분산 및 안정성을 향상시키기 위해 지지체와 촉매 사이에 원자층 증착법을 이용하여 inter-layer를 도입하였다. 이들의 구조, 형태, 및 표면의 화학적 상태는 주사전자현미경, EDS (energy dispersive spectroscopy)가 탑재된 주사전자현미경, X-선 회절, 및 X-선 광전자 분광법을 이용하여 규명하였다. 더하여 정전압-전류 측정법 및 유도 결합 플라즈마 분광 분석기을 이용하여 전기 화학 반응을 유도하고, 반응 후 전해질의 성분분석을 통해 촉매와 지지체 간의 안정성을 평가하였다. 따라서 본 결과들은 한국진공학회 하계정기학술대회를 통해 좀 더 자세히 논의될 것이다.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2004.05a
• /
• pp.46-48
• /
• 2004

현재 섬유산업에서 배출되는 톨루엔을 제어하기 위해 고가의 귀금속을 제외한 다양한 전이금속촉매를 사용하여 촉매산화반응을 모사가스로 평가하였다. 전이금속촉매의 톨루엔 촉매산화반응 및 표면특성을 요약 정리하면 다음과 같다. 반응온도 160~$640^{\circ}C$에서 톨루엔의 완전산화반응을 나타내었으며 이중 Cu와 Cr 촉매는 $340^{\circ}C$에서 99% 이상의 제어효율을 보여주는 활성이 우수한 촉매로 평가되었다. 또한 $­Al_2O_3$와 5%wt Cr/ $­Al_2O_3$의 FE­SEM을 측정한 결과 전이금속을 첨가 시 지지체 표면에 균일하게 분산되어 있음을 알 수 있었다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.127-132
• /
• 1996

촉매탑에서 수소와 물사이의 수소 동위원소 교환 반응에 의한 중수 분리 및 삼중수소 제거를 위한 소수성 촉매집합체 제조기술을 개발하기 위하여 소수성 촉매집합체 제조 특성에 대하여 연구하였다. 본 연구에서 먼저 일반적인 함침법 및 colloidal method 의하여 각각 백금을 activated carbon에 담지시켜 Pt/Carbon 촉매를 제조하고, 수소 흡착법에 의하여 촉매의 백금 분산도를 비교 분석하였다. 제조된 Pt/Carbon 촉매를 Wanke등의 방법에 따라 소수성 teflon 수지를 binding agent로 사용하여 ceramic bell-saddle 및 육면체형 packing등의 충전물 표면에 coating시켜 촉매 집합체를 제조하고 소결 온도, 충전물의 형태 및 표면 부위에 따른 surface coating 특성에 대하여 연구하였다.

• Clean Technology
• /
• v.23 no.2
• /
• pp.213-220
• /
• 2017

Dry reforming of methane to synthesis gas was investigated over a series of Ni/HY catalysts promoted by Mg, Ca, K and Mn. These catalysts were characterized by XRD, BET, SEM, and TGA analyses before and after the reaction. Conversions and product yields were increased with increasing nickel loading up to 13 wt%. Among the catalysts tested in this work, the Ni-Mg/HY catalyst showed the highest carbon resistance and the most stable catalytic performance. It was revealed that the addition of Mg promoter reduced the nickel particle size and produced the highly dispersed nickel particles, and consequently, retarded the catalyst deactivation.

• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.1-9
• /
• 2011

Platinum catalysts were prepared by impregnating platinum precursor on titania-, vanadia-, zirconia- and ceria-incorporated silicas followed by hydrogen peroxide treatment. The effects of the oxide incorporation and the hydrogen peroxide treatment in the preparation of the platinum catalysts on their platinum dispersion and catalytic activity in carbon monoxide oxidation were investigated. XRD, TEM, EXAFS, XPS and carbon monoxide chemisorption studies confirmed the high dispersion of platinum even on silica by the oxide incorporation and hydrogen peroxide treatment. However, the type of oxides incorporated on silica caused considerable variances in the adsorption and the catalytic activity in the oxidation of carbon monoxide on them. The incorporation of titania, zirconia and ceria on silica and further hydrogen peroxide treatment enhanced the platinum dispersion, resulting in the improved catalytic activities. Among the catalysts supported on the oxide-incorporated silicas, the platinum catalyst supported on zirconia-incorporated silica exhibited the highest activity because of the highest platinum dispersion due to the formation of Pt-O-Zr bonds.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.357-364
• /
• 2023

Selective catalytic reduction (SCR) is the most effective method for reducing nitrogen oxide emissions, but the operating temperature range of V₂O₅-WO₃/TiO₂ catalysts is narrow (300~400℃). In this study, a new catalyst with an operating temperature range of 200~450℃ was developed. The catalyst poison, ammonium bisulfate, generated during the SCR process can be removed by heating above 350℃. To increase the number of active sites and promote the dispersion of active materials, titanium isopropoxide (TTIP) treatment was performed on the TiO₂ support with various TTIP/TiO₂ mass ratios. Among them, the 5 wt% TTIP loaded catalyst showed improved performance due to higher thermal stability caused by high W dispersion and the formation of V⁵⁺. In addition, the 5 wt% TTIP-loaded catalyst prepared by a one-step co-precipitation method showed greater V-OH and W-OH dispersion and enhanced interactions in contrast to conventional methods, resulting in higher catalytic activity at lower temperatures. This review article aims to provide an accessible explanation for researchers investigating how to improve the surface properties of TiO2 catalysts using TTIP.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.224-231
• /
• 1990

To improve the dispersion of platinum catalyst, the effects of carbon black surface treatment, solvents, surfactants, and ultrasonic homogenizing were examined. Upon introducing the hydrophilic groups acting as an anchorage center of the catalyst on the surface of carbon black by oxidation, the migrating and growing of platinum particles(or ions) during reduction could be restricted. When mixed solvents, surfactants, or ultrasonic homogenizer were used to disperse catalysts on the carbon black, the dispersion of catalyst could be improved, due to the good permeation of chloroplatinic acid through the pore of carbon black. Among the impregnation methods, the method using ultrasonic homogenizer with mixed solvent was the most excellent. Using this method the particle sized could be minimized in less than $30A^{\circ}$ and distributed homogeneously.