• Korean Journal of Agricultural Science
• /
• v.23 no.1
• /
• pp.39-50
• /
• 1996

The normal cement concrete is widely used material to build the construction recently, but it has a fault to increase the dead load on account of its unit weight is large compared with strength. So, many engineers are continuously searching for new materials of construction to provide greater performance at lower density. Many studies were carried out on the lightweight aggregate concrete in foreign country in the latter half of the 19th century, therefore lightweight aggregate concrete has been used successfully for many years for structural members. The main purpose of the work described in this paper were to establish its physical and mechanical properties of no-fines lightweight concrete using synthetic lightweight coarse aggregates. Test results are summarized as follows ; The water-cement ratio was shown less than 33% in use synthetic lightweight coarse aggregates, unit weights of synthetic lightweight concrete was shown less than $1,800kg/m^3$ and compressive strength was higher than $200kg/m^2$. And the pulse velocity was more than 3,000m/sec. The relationship of compressive strength between unit weight and pulse velocity was shown to be approximately linear.

• The Journal of Engineering Geology
• /
• v.21 no.1
• /
• pp.15-24
• /
• 2011

To clarify the distribution of joints and fracture zones in the Cheongju granitic mass, we analyzed drill-core and geophysical well-logging data obtained at two boreholes located 30 m from each other. Lithological properties were investigated from the drill-core data and the samples were classified based on the rock mass rating (RMR) and on rock quality designation (RQD). Subsurface discontinuities within soft and hard rocks were examined by geophysical well-logging and cross-hole seismic tomography. The velocity structures constructed from seismic tomography are well correlated with the profile of bedrock depth, previously mapped from a seismic refraction survey. Dynamic elastic moduli, obtained from full waveform sonic and ${\gamma}-{\gamma}$ logging, were interrelated with P-wave velocities to investigate the dynamic properties of the rock mass. Compared with the correlation graph between elastic moduli and velocities for hard rock at borehole BH-1, the correlation points for BH-2 data showed a wide scatter. These scattered points reflect the greater abundance of joints and fractures near borehole BH-2. This interpretation is supported by observations by acoustic televiewer (ATV) and optical televiewer (OTV) image loggings.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.4
• /
• pp.337-346
• /
• 1992

Hydroacoustic surveys were conducted in the East China Sea, in the summers of 1990-1991 to investigate the distribution and migration behavior of fish, such as the diel changes in the distributions of fish, the thermoselection behavior of fish, and the fish reactions to a surveying vessel. The hydroacoustic observations were taken with a scientific echo sounder operating at 50kHz and a microcomputer-based echo processor. Fish samples were collected by bottom trawling and temperature was measured with a DBT system. The patterns of fish distributions were compared with the vertical profiles of water temperature. The results obtained can be summarized as follows: 1. The time series of hydroacoustic observations on the downward migration at dawn in the central region of East China Sea showed that the migration rate was 0.24 m/min. In this region, most of the fish collected by bottom trawling during the surveys were squid (Photologio edulis f. budo) and horse mackeral (Trachurus japonicus). 2. The hydroacoustic observations, which together associated with temperature data, indicated that squid and horse mackeral concentrated nocturally in a narrow vertical band of thermocline, particularly in summer when the survey region was strongly stratified. This result suggest that the nocturnal vertical distribution of these species evidently is controlled by temperature. 3. When the survey vessel, that is running at a speed of 11 knots, has suddenly stopped, the fish which concentrated beneath the transducer showed a strong avoidance reaction in the form of rapid downward migration. After a few minutes, the descending reaction disappeared and the fish slowly began the upward migration toward their original swimming positions. Trawl data suggest that the fish, which showed the avoidance reaction, was Liparis tessellatus.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.55-59
• /
• 2004

We fabricates the $TiO_2$ thin film from anatase phase $TiO_2$ powder having good photocatalytic property using aerosol deposition method at room temperature. Aerosol deposition method, which sprays an aerosol powder with ultrasonic velocity and deposits a thin film on substrate at low temperature, has the advantages of low thermal stress and low cost. To fabricate the $TiO_2$ thin film, the aerosol bath pressure and chamber pressure were 500 torr and 0.4 torr, respectively. The difference of aerosol bath pressure and chamber pressure accelerated the $TiO_2$ nano powder to ultrasonic velocity through the nozzle of $0.4 mm{\times}10 mm$ and $TiO_2$ thin film was finally formed. SS mesh with diameter of 50 mm was used as a substrate to apply the $TiO_2$ thin film to water quality purification. The raw powder was dehydrated for the good dispersion of $TiO_2$ powder. To suppress the formation of second particle, the powder was dispersed for 90 min in alcohol bath by ultrasonic treatment and desiccated. The grain size of $1 {\mu}m$ was observed in $TiO_2$ thin film deposited on SUS mesh by scanning electron microscopy (SEM). The anatase phase of $TiO_2$ thin film was also observed by X-ray diffraction (XRD) and the anatase phase of raw powder was nicely maintained after aerosol deposition. The results are applicable to water treatment filter having photocatalytic reaction.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.3
• /
• pp.269-275
• /
• 2017

Shipwreck remains below the seabed not only effect the ocean currents and tides, but influence the physical properties of sediments and sedimentary environments that comprise the seabed. In particular, the influence of local shipwrecks discovered buried in the seabed on the sediment is visible. In this study, sediments were collected from the surrounding area of Taean Mado No.3 shipwreck using grab samplers and vibro-corers. The physical properties of these sediments were analyzed to evaluate the impact of the Taean Mado shipwreck No.3 remains. Sediment core analysis by means of density and ultrasonic velocity showed that shear strength tended to increase with depth, whereas moisture content and porosity tended to decrease with depth. Grain size analysis results are shown in terms of Folk's classification, where the grain size of the core samples in the study area indicate mud or sandy mud, and that of the grab sample indicates a muddy sand. Results of the sedimentation rate analysis indicate a rate of 2.84 cm/year and carbon dating of the 150 cm deep seashell indicates the Neolithic age. These sediments were analyzed for the study of the relationship between the Taean Mado shipwreck No.3 remains and the physical properties of the sediment.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.2
• /
• pp.63-69
• /
• 2012

Recently, the cement industries brought very severe environment problems such as resource depletion and global warming with massive carbon dioxide during its production. The number of cases using industrial by-products such as the ground granulated blast furnace slag (GGBFS) in concrete mixtures is increasing to resolve the environmental issue. GGBFS is mainly used in the range between 20 to 50% to replace cement, but nowadays lots of researches are carried out to develop the alkali-activated slag (AAS) concrete with no cement. In this study, the early age properties of alkali activated slag (AAS) mortar are investigated to obtain the fundamental data for AAS concrete application to structural members. The experimental variables were the water-binder ratios of 0.3, 0.4, and 0.5 and NaOH as the alkali activator of 4%, 8%, and 12% by the mass of GGBFS, and compressive strength, flow, setting time, and ultrasonic pulse velocity of AAS mortars were measured and analyzed. It is found from the test results that as the normal concrete the lower W/B, the higher compressive strength. However, superplasticizer has to be used for producing high strength AAS concrete because the workability of AAS mortar are significantly lowered.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.774-779
• /
• 2007

IDF 곡선은 전통적으로 지점에서의 과거 관측 강우량 시계열 자료를 수집하여 작성하여 왔으며, 이때 과거 강우량 자료는 정상성을 지니고 있고 미래를 대변한다는 가정을 전제로 한다. 그러나 이미 많은 연구자들에 의해 기후변화가 전구적으로 발생하고 있으며 우리나라에서도 더 이상 기후변화의 사실여부는 이제 더이상 논란 꺼리가 아니다. 특히, 기후변화의 영향을 직접적으로 받을 수밖에 없는 수자원 분야에서는 1990년대부터 잦은 홍수와 가뭄의 반복으로 곤란을 겪고 있다. 특히, 우리나라는 협소한 국토면적과 과다한 인구로 토지나 수자원 등 국토자원 이용의 강도가 다른 나라에 비하여 현저하게 높기 때문에 지구온난화에 따른 기후변화와 같은 약간의 기후변동으로도 심각한 문제가 발생할 가능성이 내포되어 있다. 특히, 기후변화는 유역 규모의 강우 발생 패턴과 강우량의 증가 및 감소에 영향을 미치게 되며 이로 인해 강우 시계열 자료는 비정상성과 경향성을 지니게 된다. 그러나 지금까지는 IDF 곡선의 작성시 강우의 경향성을 무시해 왔다. 본 연구에서는 기후변화가 IDF 곡선에 미치는 영향을 분석하기 위하여 GCM 기후변화 시나리오를 이용하여 IDF 곡선을 작성하였다. 이를 위하여 먼저, YONU CGCM의 제한실험과 점증실험을 실시하여 전구적 규모의 기후변화 시나리오를 작성하였으며, 통계학적 축소기법과 추계학적 일기발생기법을 이용하여 대상지점의 일 수문기상 시계열을 모의하였다. 그리고 BLRP(Bartlett Lewis Rectangular Pulse) 모형과 분해(koutsoyiannis, 2000) 기법을 이용하여 모의된 일 강우 자료를 시자료로 분해하였으며 이를 이용하여 IDF 곡선을 작성하였다. 그 결과, 기후변화 시 지속기간별 재현기간별 강우량이 현재에 크게 비해 증가됨을 확인할 수 있었다.으며 여러명이 동시에 서버에 접속을 하기 때문에 컴퓨터에 부하가 많이 걸리는 모델링이나 복잡한 분석은 실시하기 어려우며, 대용량 데이터를 전송할 수 있는 대역폭이 확보 되어야 한다. 또한, Internet 환경으로 개발을 해야되기 때문에 데스크탑용 GIS에 비해 개발속도가 느리며 개발 초기비용이 많이 들게 된다. 하지만, 네트워크 기술의 발달과 모바일과의 연계 등으로 이러한 약점을 극복할 수 있을 것으로 판단된다. 따라서 본 논문에서는 인터넷 GIS를 이용하여 홍수재해 정보를 검색, 처리, 분석, 예경보할 수 있는 홍수방재정보 시스템을 구축토록 하였다.비해 초음파 감시하 치골상부 방광천자가 정확하고 안전한 채뇨법으로 권장되어야 한다고 생각한다.應裝置) 및 운용(運用)에 별다른 어려움이 없고, 내열성(耐熱性)이 강(强)하므로 쉬운 조건하(條件下)에서 경제적(經濟的)으로 공업적(工業的) 이용(利用)에 유리(有利)하다고 판단(判斷)되어진다.reatinine은 함량이 적었다. 관능검사결과(官能檢査結果) 자가소화(自家消化)시킨 크릴간장은 효소(酵素)처리한 것이나 재래식 콩간장에 비하여 품질 면에서 손색이 없고 저장성(貯藏性)이 좋은 크릴간장을 제조(製造)할 수 있다는 결론을 얻었다.이 있음을 확인할 수 있었다.에 착안하여 침전시 슬러지층과 상등액의 온도차를 측정하여 대사열량의 발생량을 측정하고 슬러지의 활성을 측정할 수 있는 방법을 개발하였다.enin과 Rhaponticin의 작용(作用)에 의(依)한 것이며, 이는 한의학(韓醫學) 방제(方劑) 원리(原理)인 군신좌사(君臣佐使) 이론(理論)에서 군약(君藥)이 주증(主症)에 주(主)로 작용(作用)하는 약물(藥物)이라는 것을 밝혀주는 것이라고 사료(思料)된다.일전 $13.447\;{\mu}g/hr/g$, 섭취 7일중 $8.123

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.325-331
• /
• 2016

Computational fluid numerical analysis using the commercial code CFX was performed to develop a Pelton turbine for a pico hydro power generator using the circulating water of a cooling tower in a large building. The performance of the Pelton turbine was examined for different design factors, such as the bucket shape, in which the Pelton wheel was connected in an appropriate manner to the pipe section, and the number of buckets in order to find the optimal design of Pelton turbine for a pico hydro power using surplus water. A benchmark test was carried out on the manufactured small scale Pelton turbine to validate the design method of the Pelton turbine by numerical analysis. The results obtained by comparing the flow characteristics and power output measured using the ultrasonic flowmeter, the pressure transducer and the oscilloscope with the numerical results confirmed the validity of the analytical design method. The possibility of developing Pelton turbines for kW class pico hydro power generators using surplus water with an average circulation velocity of 1.2 m/s for the chosen bucket shape and number of buckets in a 30 m high building was confirmed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.128-128
• /
• 2018

최근 디스플레이 기술은 보다 가볍고, 얇고, 선명한 스마트 형태로 발전되고 있다. 특히 스마트산업의 성장으로 터치스크린패널(Touch Screen Panel, TSP)을 사용하는 기술이 다양해짐에 따라 더 높은 감도와 해상도를 달성하기 위한 핵심기술이 필요한 실정이다. TSP는 저항막 방식, 정전용량 방식, 적외선 방식, 초음파 방식 등 다양한 방식이 있다. 그 중 정전용량방식 터치 패널 (Capacitive type touch panel, CTTP)은 다른 유형에 비해 빠른 반응속도 및 멀티 터치 기능 등의 이점을 가지고 있기 때문에 연구의 초점이 되고 있다. 이를 실현하기 위해서 CTTP은 가시광영역의 높은 투과율과 낮은 비저항을 필요로 하기 때문에 박막의 초 슬림화 및 고 결정화도가 선행되어야만 한다. CTTP에 사용되는 투명전극 소재 중에서 40%의 비중을 차지하고 있는 ITO박막은 내구성과 시인성이 좋으나 생산 비용이 비싸다는 단점이 있다. 한편, 반응성 스퍼터링은 기존에 단일 소결체를 사용한 DC마그네트론 스퍼터링법보다 높은 증착률과 낮은 생산 비용으로 초박막을 만들 수 있다는 장점을 가진다. 본 실험에서는 In/Sn (2wt%) 금속 합금 타깃을 사용한 반응성 스퍼터링법을 이용하여 기판 온도 (RT 및 $140^{\circ}C$)에서 두께 30 nm의 In-Sn-O (ITO)박막을 증착하고, 대기 중 $140^{\circ}C$ 온도에서 시간에 따라 열처리한 후 박막의 물성을 관찰하였다. 증착 중 기판 가열을 하지 않은 ITO 박막의 경우, 열처리 시간이 증가함에 따라 비저항은 감소하였고, 홀 이동도는 현저하게 증가하였으며 캐리어 밀도에서는 별다른 차이가 없었다. 이를 통해 비저항의 감소는 캐리어 농도보다는 결정화를 통한 이동도의 증가와 관련 있다는 것을 확인할 수 있었다. 열처리 시간에 따른 박막의 핵 생성 및 결정 성장은 투과 전자 현미경(TEM)으로 명확하게 확인하였으며, 완전 결정화 된 박막의 grain size는 300~500 nm로 확인되었다. 기판온도 $140^{\circ}C$에서 증착한 박막의 경우, 후 열처리를 하지 않은 상태에서도 이미 결정화 된 것을 확인할 수 있었으며, 후 열처리 시에도 grain size에는 큰 변화가 없었다. 이는 증착 중에 박막의 결정화가 이미 완결된 것으로 판단된다. 또한, RT에서 증착한 박막의 경우에는 후 열처리 초기에는 산소공공등과 같은 결함들의 농도가 감소하여 투과율이 증가하였으나 완전한 결정화가 일어난 후에는 투과율이 약간 감소한 것을 확인할 수 있었다. 이는 결정화 시 박막의 표면 조도가 증가하였고 이로 인해 빛의 산란이 증가하여 투과율이 감소한 것으로 판단된다. 이러한 결과로 반응성 스퍼터링 공정으로 제조한 ITO 초박막은 후열처리에 의한 완전한 결정화를 이룰 수 있으며, 이를 통해 얻은 낮은 비저항과 높은 투과율은 고품질 TSP에 적용될 가능성을 가진다고 판단된다.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.12 no.1
• /
• pp.37-43
• /
• 2006

PURPOSE: Previous studies have documented the lack of ultrasound's non-thermal effects on nerve conduction using frequencies of 1 MHz and 870 kHz. The purpose of this study was to determine the biophysical effects of continuous ultrasound on median local forearm temperature and motor nerve conduction velocities using frequencies of 3.0 MHz. SUBJECTS: Twelve healthy subjects (6 males, 6 females, age $22.30{\pm}2.41$ yrs, weight $61.33{\pm}10.16$ kg, height $167.58{\pm}8.04$ cm) without a history of neurological or musculoskeletal injury to their dominant arm volunteered for this study. METHODS AND MATERIALS: Each subject received a total of five treatments, one each at .0, 0.5, 1.0, 1.5, 2.0 W/$cm^2$ of 3 MHz continuous ultrasound on the anterior surface of the middle area of dominant forearm for 10 minutes. Dependent measures for forearm local temperature and median motor nerve conduction velocity (MNCV) were taken pretreatment and immediately post-treatment. One-way ANOVA were used for each dependent measure. RESULTS: The posttreatment forearm local temperature were differed significantly (p<0.001) between intensities of ultrasound. The posttreatment forearm local temperature of the ultrasound treated with 1.0 w/$cm^2$, 1.5 w/$cm^2$ and 2.0 w/$cm^2$ were significantly higher than 0.5 w/$cm^2$ and 0.0 w/$cm^2$ of ultrasound (p<0.05). The posttreatment median MNCV were differed significantly from the respective pretreatment velocities (p<0.001). The MNCV of the ultrasound treated with 0.0 w/$cm^2$ and 0.5 w/$cm^2$ were significantly (p<0.05) slower than that observed pretreatment, while the three ultrasound intensities produced significantly increased posttreatment MNCV: 1.0 w/$cm^2$ and 1.5 w/$cm^2$ and 2.0 W/$cm^2$. The posttreatment MNCV at 2.0 w/$cm^2$ and 1.5 w/$cm^2$ was significantly faster than that at 0 w/$cm^2$, 0.5 w/$cm^2$ and 1.0 w/$cm^2$ (p<0.05), the MNCV at 1.0 w/$cm^2$ was significantly faster than that associated with 0 w/$cm^2$ and 0.5 w/$cm^2$ of ultrasound (p<0.05). CONCLUSIONS: The decreased median motor forearm local temperature and MNCV of the ultrasound treated with 0.0 w/$cm^2$ and 0.5 w/$cm^2$ were attributed to the cooling effect by ultrasound transmission gel. Local forearm temperature and nerve conduction velocity were directly related to the intensity of ultrasound. Alterations in MNCV from ultrasound on healthy nerves appeared to be related to temperature changes induced by thermal effects of ultrasound.