• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.55-59
• /
• 2007

It is known that the adhesive interface testing of the rocket motor which using the ultrasonic wave iS superior to the other testing methods about the economically detectable abiliη of the defects. But, the signal analysis of the ultrasonic wave takes too much time and effort that the time interval of the transmitted pulse and the received pulse is too short to be separated the reflected signals because the structure of the rocket motor is multi-layers. The ultrasonic testing of rocket motor have been only applied with automatic system about extremely limited area like the debond in adhesive interface between the motor case and insulator. In this study the new technique to detect the debond between the liner and the propellant using the property of the resonance and Lamb waves was described as comparing the existence ultrasonic testing.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.4
• /
• pp.401-409
• /
• 2012

Ultrasonic testing are far superior to other nondestructive tests for detecting the disbond interface which occurred in adhesive interface. However, a solid rocket motor consisting of a steel case, rubber insulation, liner, and propellant poses many difficulties for analyzing ultrasonic waves because of the superposition of reflected waves and large differences in acoustic impedance of various materials. Therefore, ultrasonic tests for detecting the disbond interface in solid rocket motor have been applied in very limited areas between the steel case and rubber insulation using an automatic C-scan system. The existing ultrasonic test cannot detect the disbond interface between the liner and propellant of a solid rocket motor because most of the ultrasonic waves are absorbed in the rubber material which has low acoustic impedance. This problem could be overcome by analyzing the resonance frequency from the frequency spectrum using the ultrasonic resonance method. In this paper, a new technique to detect the disbond interface between the liner and propellant using ultrasonic resonance characteristics is discussed in detail.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.27-27
• /
• 1999

본 연구에서는 초음파 Immersion법을 이용하여 복합재 연소관내에 존재하는 결함을 검출하는 방법에 대하여 연구하였으며, 이를 위하여 FRP의 delamination, FRP-EPDM간의 미접착을 모사한 모의 결함 시편을 제작하여 시험하였다. 먼저 복합재료에 대한 초음파 시험방법을 최적화하기 위하여 가장 검출 감도가 좋은 탐촉자의 적용 주파수조건 및 물거리를 구하였으며, 이들 최적 조건으로 모의 결함 시편을 A, B, C-Scan하여 결함을 검출 분석하였다. 그리고 시험 자료를 바탕으로 데이터 값을 분석함으로써 복합재료에서의 음파 속도, 음향 임피던스, 반사율 및 투과율 등 복합재료의 초음파 특성을 산출하였으며, 동 시편에 대한 X-ray 필름을 촬영하여 그 결과를 초음파 시험 결과와 비교 분석하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.11-16
• /
• 2006

The object of this study is to develop new examination techniques for detecting the debonds in adhesive interface of different kinds of the material. Ultrasonic signal was modeled by theoretically analyzing ultrasonic propagation phenomenon of the adhesive interface and debonding interface. The test method using the phase reversal of the debonding interface applied to the FRP/Rubber test block. Aluminum/Rubber test block with the flat bottom hole was manufactured to quantitatively evaluate the minimum detection ability of the defects. The pulse echo reflection method and the phase reversal method were mutually compared and it was estimated that the phase reversal method could detect the debonds on the basis of the theoretically predicted ultrasonic signal and ultrasonic test data.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.2
• /
• pp.9-16
• /
• 2009

The object of this study is to develop new examination technique for detecting debond in adhesive interface of different kinds of materials. Ultrasonic signal was modeled by theoretically analyzing ultrasonic propagation phenomenon of the adhesive interface and debonding interface. The test method using the phase reversal of the debonding interface applied to the FRP/Rubber test block. Aluminum/Rubber test block with the flat bottom hole was manufactured to evaluate quantitatively the minimum detection ability of defects. The pulse echo reflection method and the phase reversal method were mutually compared and it was estimated that the phase reversal method could detect the debond on the basis of the theoretically predicted ultrasonic signal and ultrasonic test data.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.967-973
• /
• 2013

An accelerated ultrasonic fatigue test(UFT) has been used for analyzing very high cycle fatigue( VHCF, $N_f$ > $10^7$). This study reviews how the test specimen is to be determined. We focus on UFT using a resonance of 20 kHz. The specimen geometry is determined by selecting test materials by using a dynamic Young's modulus and wavelength of 20 kHz. The dynamic Young's modulus is calculated at the resonant frequency. Through a resonant vibration test at 20 kHz, the length of the specimen is calculated. By determining the shape of the specimen, the stress during the UFT is calculated. The UFT results should be comparable at the test frequency and the specimen geometry obtained by the conventional fatigue tests.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.711-717
• /
• 2014

An accelerated ultrasonic fatigue test (UFT) was used for analyzing very high cycle fatigue (VHCF, $N_f$ > $10^7$) behaviors of a specimen with a test resonance of 20 kHz. Using the finite element method (FEM), the dynamic behaviors of the specimen was studied by calculating the stresses along its gauge portion, with displacement. The shape of gauge portion profile was assumed to be a hyperbolic according to the stress equation of the UFT. However, as the specimen used in the test had a circular arc profile, the FEM was used for studying the local stresses for two cases of the gauge profile. The results were compared with those obtain from the stress equation of the UFT. The dynamic behavior of the gauge portion could be understood for further comparison with the actual results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.5
• /
• pp.89-96
• /
• 2012

The rubber side could be contaminated using the existing pulse echo method because the ultrasonic wave was incident on the rubber side from the interior of the steel motor case, which could lead to the critical disbond defect. To develop the test method which can be replaced the existing method, the ultrasonic wave was incident on steel face of the steel/rubber adhesive test block. Rubber resonance frequencies measured from the steel/rubber adhesive test block were in good agreement with theoretically predicted rubber resonance frequencies. This paper was described about the ultrasonic resonance method to convert the rubber resonance frequency into the rubber thickness.

• 연구논문집
• /
• s.28
• /
• pp.229-238
• /
• 1998

Materials and parts required for nondestructive testing should be evaluated using with standard block. And it is ruled that standard blocks should be fabricated from same or similar material with test specimen. In order to manufacture and export materials and parts, quality assurance system should be required. In this paper, ultrasonic characteristics of ASTM 4340 steel ultrasonic standard block are investigated for nondestructive evaluation of udimet 720Li disc. Microstructures of udimet 720Li alloy are investigated using with optical and transmission electron microscope. Also ultrasonic transit time and attenuation are measured from high power ultrasonic analysis system with phase adjustment method. Conclusively, it is proved that 4340 steel ultrasonic standard block can be use for nondestructive evaluation of udimet 720Li disc.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.562-569
• /
• 2012

The rubber side could be contaminated using the existing pulse echo method because the ultrasonic wave was incident on the rubber side from the interior of the steel motor case, which could lead to the critical disbond defect. To develop the test method which can be replaced the existing method, the ultrasonic wave was incident on steel face of the steel/rubber adhesive test block. Rubber resonance frequencies measured from the steel/rubber adhesive test block were in good agreement with theoretically predicted rubber resonance frequencies. This paper was described about the ultrasonic resonance method to convert the rubber resonance frequency into the rubber thickness.