• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.86-94
• /
• 1999

Measured shock wave effects were investigated by changing shock strength and position with particular emphasis on the stability limits of hydrogen-air jet flames. For this purpose, a supersonic nonpremixed, jet-like flame was stabilized along the axis of a Mach 2.5 wind tunnel, and wedges were mounted on the sidewall in order to interact oblique shock waves with the flame. This experiment was the first reacting flow experiment interacting with shock waves. Schilieren visualization pictures, wall static pressures, and flame stability limits were measured and compared to corresponding flames without shock-flame interaction. Substantial improvements in the flame stability limits were achieved by properly interacting the shock waves with the flameholding recirculation zone. The reason for the significant improvement in flame stability limits is believed to be the adverse pressure gradient caused by the shock, which can elongate the recirculation zone.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.1-13
• /
• 2007

Scramjet engine is one of the most promising propulsion systems for future transport. For the ground test with T4 shock tunnel, model scramjet engine is designed. Design flight Mach number is 7.6 and flight altitude is 30km. Engine intake is designed by Levenberg-Marquardt optimization method and Korkegi relation. Furthermore, cowl cut out region is installed by the rule of Kantrowitz limit. Inside the combustor, cavity type flame holder is installed. Cavity is designed by Rayleigh line relation and PSR model. Numerical analysis is performed for the design confirm.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.62-69
• /
• 2014

This paper presents a preliminary study of a convergent divergent nozzle in an afterburning turbofan engine of a supersonic aircraft engine. In order to design a convergent divergent nozzle, cycle model of a low bypass afterburning turbofan engine of which thrust class is 29,000 lbf at a sea level static condition is established. The cycle analysis at the design point is conducted by Gasturb 12 software and one dimensional gas properties at a downstream direction of the turbine are obtained. The dimension and configuration of an model turbofan engine are derived from take-off operation with wet reheat condition. The off-design cycle calculation is conducted at the all flight envelope on the maximum flight Mach number of 2.0 and maximum flight altitude of 15,000 m.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.138-143
• /
• 2009

Thermal barrier efficiency and endurance of coatings in liquid rocket engine combustor were evaluated for air plasma spray coating and electro/electroless plating. The result of firing tests has revealed occasional occurrence of local delamination of $ZrO_2$, NiCrAlY coating obtained by the method of air plasma spray in the region of supersonic flow and it necessitated a new coating method as a substitution. It was found that Ni-Cr coating by means of electro/electroless plating can substitute $ZrO_2$, NiCrAlY coatings of air plasma spray in terms of thermal barrier efficiency and endurance.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.561-565
• /
• 2009

The performance of supersonic impulse turbine was investigated experimentally. Experiment was performed with the compressed air instead of the high temperature burned gas because of the limitation of test facility and danger. As a result of the experiment with the compressed air, the performance in the real gas(burned gas) was predicted by the similarity method. The nozzle area of prototype turbine was calculated based on the real gas. So, it is difficult to satisfy the similarity conditions completely. Two similarity conditions were set and the design point for real gas was existed between two similarity conditions. And, the new turbine test model with calculated nozzle area based on the compressed air was tested. Therefore, similarity point of the new turbine test model was also existed between above two similarity points. It means that the design point for real gas was similar to the test point with the new turbine model.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.14-14
• /
• 1998

램제트 엔진은 초음속에서 공기가 충격파를 통해 아음속으로 속도가 낮아지고 압력이 증가하는 램 압축 현상을 이용하되 압축기를 사용하지 않고 아음속 상태에서 연소하는 구조로 되어 있다. 따라서 각 부품의 성능은 독립적이지 않으며 전체적인 성능을 규명하기 위해서는 공기 흡입구와 연소실, 연료 분사체계 등의 상호작용을 고려하여 유동의 특성과 그에 따른 연소현상의 특성을 함께 고려해야만 한다. 본 연구에서는 속도 범위 Mach 5이내, 고도 30km이내의 운항조건을 갖는 유도 무기에 장착될 램제트 엔진 개발을 위한 연구의 첫 번째 단계로써, 램제트 연소실내의 유동장해석을 실험과 수치해석 두 분야로 나누어 수행하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.13-19
• /
• 2003

A supersonic ground test facility to develop Ramjet and SCRamjet(Supersonic Combustion Ramjet) engine should be able to simulate high altitude and high Mach number conditions including air total pressure, oxygen level and specific heat ratio at the combustion chamber entrance. The test facility also should simulate the effect of oblique shock wave caused by the flight vehicle. The test facility developed in this study is supersonic free-jet blowdown type, which consists of high pressure air supply source(maximum pressure=32MPa), air heater(vitiation type), supersonic diffuser, ejector, and test chamber(nozzle exit dimension=200mm$\times$200mm).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.4
• /
• pp.53-62
• /
• 2003

A supersonic ground test facility to develop Ramjet and SCRamjet(Supersonic Combustion Ramjet) engine should be able to simulate high altitude and high Mach number conditions including air total pressure, oxygen level and specific heat ratio at the combustion chamber entrance. The test facility also should simulate the effect of oblique shock wave caused by the flight vehicle. The test facility developed in this study is supersonic free-jet blow down type, which consists of high pressure air supply source(maximum pressure=32MPa), air heater(vitiation type), supersonic diffuser, ejector, and test chamber(nozzle exit dimension=200mm${\times}$200mm).

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.899-905
• /
• 2009

Most supersonic-flow test facility has axisymmetric nozzles or two-dimensional symmetric nozzles. Compared to these nozzles, a two-dimensional asymmetric nozzle has advantages of reducing low cost for various Mach number testing and undesirable flow structure such as shock wave reflection because the nozzle part can be directly connected to the test section part in this type of nozzle. The two-dimensional asymmetric nozzle, which was Mach number 2, was designed for supersonic combustion experiment. And it was verified with the numerical analysis and visualization of Mach wave. This study suggested the practical method for design and verification of supersonic two dimensional asymmetric nozzles.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.61-61
• /
• 2002

스크램 제트 엔진의 설계에서 초음속으로 유입된 공기의 짧은 잔류시간으로 인한 연료-공기의 혼합은 가장 중요하며 해결하기 힘든 문제이다. 전헝적인 비행 조건에서 흡입 공기가 극초음속 비행기 엔진 내에서 잔류하는 시간의 단위는 1 ms 정도이어서 짧은 시간 동안 연료와 공기는 효율적으로 혼합되어야 하며, 최대의 추진력을 얻기 위하여 과도한 공력저항없이 연소 가능한 연료-공기 혼합기를 생성시킬 수 있는 효율적인 연료-공기의 혼합 방법이 요구된다. 현재까지 가장 많이 연구되어 온 혼합 방법은 엔진 입구로 들어오는 공기 유동에 수직 방향으로 연료를 분사하는 것으로 이 방법은 연료 유동 방향과 공기 유동 방향이 수직이기 때문에 추력 손실이 생기는 단점을 갖고 있지만, 초음속으로 유입되는 공기에 수직으로 연료를 분사하게되면 분사 위치 앞에 궁형 충격파가 생겨서 감속되어 유동이 회전하는 재순환영역이 생기고 연료의 혼합이 잘 이루어지는 장점이 있다.