• Electrical & Electronic Materials
• /
• v.6 no.5
• /
• pp.446-453
• /
• 1993

초기충진압력이 서로 다른 시편에 가한 가압횟수와 열처리시간의 혼합공정이 임계전류밀도 특성에 미치는 영향을 관찰하기 위하여 power-in-tube방법으로 초전도 선재를 제조하였다. 일정 초기충진압력에서 테이프화를 위한 열처리 및 가압이 혼합공정횟수가 증가할수록 임계전류밀도가 증가하였다. 초기충진압력이 1000kg/$cm^{2}$에서 Bi-2223 고온상 체적비가 가장 높게 나타났고 결정립이 판상으로 성장되었을 뿐만 아니라 C축과 직각방향으로 잘 배양되어 있음을 관찰할 수 있었다. 특히 초기충진압력 1000kg/$cm^{2}$의 시편을 두께를 줄이기 위하여 3회 가압하고 450시간 열처리하였을때 임계전류밀도가 5800A/$cm^{2}$를 나타내었으며 이를 중심으로 500, 2500kg/$cm^{2}$이 양측단으로 가우시안분포를 보였다. 결론적으로 시편의 임계특성은 적정 초기충진압력, Bi-2223 고온상 체적비, 테이프화를 위한 가압횟수, 결정의 일방향배열, 결정립의 성장등에 강하게 의존함을 알 수 있었다.

• Nuclear Engineering and Technology
• /
• v.27 no.5
• /
• pp.775-783
• /
• 1995

This study is to assess the effects of increasing wall thickness on the safety margin of pressure tube in operating and of lowering initial hydrogen concentration on the DHC growth in respect to the improvement of the reliability of pressure tube in CANDU reactors. The pressure tube with thicker wall of 5.2 mm shows much higher safety margin for flaw tolerance by 25％ than the current 4.2mmm tube. The thicker pressure tubes have a great benefit in LBB assessment including the initial crack depth at which DHC occurs, the crack length at onset of leaking and the available time for action. The resistance for the pressure tube ballooning at LOCA accident is also increased with the thicker tube. The calculations for Heq concentration after 20 years of operation as a function of wall thickness and initial hydrogen concentration show that the 5.2 mm nil thickness tube with 5 ppm initial hydrogen concentration is the most resistant to DHC. with the lower initial hydrogen concentration, TSS temperature for the precipitation or hydride decreases and the crack growth during cooldown reduces.

• Journal of the Korean Vacuum Society
• /
• v.20 no.2
• /
• pp.141-145
• /
• 2011

ZnO:Al thin films were deposited by RF magnetron sputtering with various base pressure, and their structural, optical, and electrical properties were studied. The influence of the base pressure on the ZnO:Al thin film was confirmed and a high-quality thin film was obtained by controlling the base pressure. In all Al-doped ZnO thin films, the preferred orientation of (002) plane was observed and light transmittance in visible region (400 nm~800 nm) had above 85%. With decreasing of base pressure, crystallinity, resistivity, and figure of merit were improved. The improvement of resistivity with base pressure was attributed to the change of grain size.

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.122-129
• /
• 2002

The analytical models and algorithm of the SPIKE code, which has been developed by KAERI's KALIMER team to investigate the sodium-water reaction phenomena in the liquid metal reactor, were introduced with its verification calculation results. The sodium water reaction of KALIMER IHTS was evaluated. Early stage of the sodium-water reaction consists of wave and mass transfer regimes. The pressure variations were independent of specific design features in the wave transfer regime. However in the mass transfer regime, the pressure variations were strongly dependent on cover gas volume and rupture disk set pressure. The early stage SWR analysis showed that the KALIMER IHTS with an appropriate cover gas volume and rupture disk set pressure had enough margin to its design pressure.

• Journal of Energy Engineering
• /
• v.4 no.1
• /
• pp.85-94
• /
• 1995

본 연구에서는 최근 차량용 대체연료로서 주목받고 있는 천연가스의 연소특성을 규명하기 위해 밀폐된 정적연소실을 이용, 당량비, 초기압력 및 점화위치 변화에 따른 연소실험을 행하였으며, 그 결과 다음과 같은 결론을 얻었다. 메탄-공기 예혼합기의 화염전파과정은 이론혼합기 부근에서 구면형으로 진행되는데 반해, 과농 또는 과박 혼합기 그리고 점화위치가 연소실 벽면에 가까울수록 타원형으로 진행되며, 초기압력이 증가함에 따라 화염전파는 느려진다. 화염전파속도와 연소 속도는 초기압력이 낮고 점화위치가 연소실 중심에 가까울수록 빠르며, 당량비 1.0∼1.1 사이에서 최대치를 보인다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.138-141
• /
• 2010

A study to reduce the ignition peak pressure of gas generator for the missile launching system was accomplished. The igniter, as the energy release device for igniting the propellant, is aimed at simultaneous ignition of bundled 3-layered propellant grain without unstable burning. In case of our gas generator which must use the double-base propellant with low ignition property, the fast ignition of propellant and reduction of initial peak pressure should be required for the satisfaction of ejection velocity and acceleration condition. By applying MTV ignition charge for the igniter of gas generator, we accomplished all system performance requirements.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.5
• /
• pp.235-241
• /
• 2018

The internal pressure is a critical parameter for designing a pressure vessel. The static pressure that a pressure vessel must withstand is usually determined according to the various codes and standards with simple formula or numerical simulations considering the geometric parameters such as diameter and thickness of a vessel. However, there is no specific codes or technical standards we can use practically for designing of pressure vessels which have to endure the detonation pressure. Detonation pressure is a kind of dynamic pressure which causes an impulsive pressure on the vessel wall in a extremely short time duration. In addition, it is known that the magnitude of reflected pressure at the vessel wall due to the explosion can be over twice the incident pressure. Therefore, if we only consider the reflected pressure, the design of the pressure vessel can be too conservative from the economical point of view. In this study, we suggest a practical method to evaluate the magnitude of maximum allowable pressure that the pressure vessel can withstand against the detonation inside a vessel. As an example to validate the proposed method, we consider the pressure vessel containing hydrogen gas.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.35-38
• /
• 2004

부틸알데히드로 오염된 대상 부지에 Biosparging 공법의 현장 적용을 위해 적정 공기 주입 압력 조건을 도출한 결과, 주 오염층인 자갈질 모래층에 공기주입 가능 파괴압력(Pe)는 약 300mmAq로 측정되었으며 4,500mmAq 압력 조건에서는 용존 산소농도의 영향 반경이 약 3 m로 나타났다. 위의 조건을 적용하여 약 150일간 운전한 결과, 영양물질을 투입하지 않은 초기 90일 동안 최고농도 대비 약 90%가 저감되었으며 그 이후에 영양물질을 투입하여 초기 최고 농도 대비 96%가 저감되어 복원목표치인 50ppm을 모든 지역에서 만족시켰다. 또한 생분해 반응속도가 k=0.03/day로 나타나 휘발성이 낮고 생분 해도가 뛰어난 부틸알데히드로 오염된 자갈질 모래층에 Biosparging공법이 성공적으로 적용된 사례이다.

• Korean Journal of Food Science and Technology
• /
• v.32 no.2
• /
• pp.373-379
• /
• 2000

Low salt fermented anchovy was stored at $25^{\circ}C$ for a period of 20 days from the time of ultra-high pressure treatment under different operating conditions, such as magnitude of pressure($(200{\sim}500\;MPa)$, temperature$(20{\sim}50^{\circ}C)$ and treatment time$(5{\sim}20\;min)$ with viable cell count(VCC) and quality assessments conducted at regular intervals. VCC decreased logarithmically during storage. Lower values of VCC in the treated samples were observed compared to the untreated. A gradual increase in peroxide value was noticed during storage, compared to those of the untreated which showed a sudden rise. Thiobarbituric acid value decreased initially and remained at that level before rising almost exponentially between 12 and 20 days. Volatile basic nitrogen increased gradually during storage. Amino nitrogen remained almost constant up to 20 days, regardless of any conditions investigated. High pressure treatment maintained better quality during storage at $25^{\circ}C$ by reducing the viable cell count in low salt fermented anchovy.

• Journal of the Korean Institute of Gas
• /
• v.9 no.1 s.26
• /
• pp.38-43
• /
• 2005

To examine the characteristics of the explosion of city gas, the concentration of oxygen was changed with the change of initial pressure. From the result of the experiment, as the concentration of oxygen was low, the explosion limit became narrow and the minimum concentration of oxygen for the explosion was $12\%$. Furthermore, As the increase of the initial pressure, explosion ranges were a little increased. And as the change of the initial pressure, the maximum explosion pressure were $6.3 kgf/cm^2{\cdot}g,\;12.7 kgf/cm^2{\cdot}g$ and the maximum pressure rising velocity were $245.63 kgf/cm^2/s,\;427.88 kgf/cm^2/s$.