• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.971-975
• /
• 2009

본 연구에서는 격자강우량과 GIS와 연계한 격자기반의 공간수문자료들을 모형의 입력매개변수로 활용하고, 수계망을 통하여 유역 출구까지 운동파(kinematic wave)이론에 의해 유출량을 물리적으로 추적해 나가는 격자기반의 분포형 강우-유출모형인 K-DRUM(Kwater Distributed RUnoff Model)을 개발하였고, 지표유출량에 가장 큰 영향을 주지만 실제 관측 및 적용이 용이하지 않은 유역의 초기토양함수상태에 대한 자동보정기법을 개발하였다. 개발된 자동보정기법을 이용하여 남강댐유역을 대상으로 적용가능성을 평가하였다. 연구에서 사용한 강우사상은 남강댐 유역에 큰 영향을 준 태풍 루사 (2002년 8월 31일 01시$^{\sim}$9월1일 23시), 태풍 매미 (2003년 9월 12일 01시$^{\sim}$9월13일 23시), 2004년의 대류성강우 (2004년 7월14일 01시$^{\sim}$7월 16일 10시) 및 태풍 에위니아 (2006년 7월 8일 18시$^{\sim}$7월11일 12시)의 총 4개의 사상을 대상으로 하였다. 개발한 유역의 초기토양함수상태 자동보정기법에 의한 유출모의의 적용성을 검토하기 위하여 모의에 사용된 매개변수 중 토지피복도에 의해 결정되는 조도계수와 토양도에 의해 결정되는 유효토심, 흡인수두계수, 공극률 및 투수계수는 4개의 강우사상에서 모두 동일한 조건으로 설정하였고, 유역내 토양 내부 수분함유량 산정을 위한 초기 기저유출량은 검토대상 기간 시점부에서 관측된 유출량으로 설정하였다. 초기토양함수상태 자동보정기법 적용을 통한 유출해석의 정확도는 체적오차 백분율(VER)과 첨두 유량 오차 백분율(QER)을 이용하여 평가하였으며, 이를 통해 본 모형이 유출량에 대한 정확성을 확보하고자 하였다. 본 연구에서 개발된 자동보정 기법을 적용한 결과, 초기토양조건을 설정하는데 있어서 기존의 시행착오법으로 인해 소요되는 시간과 유역내 토양 특성과 지형형상을 고려하지 않는 설정으로 인해 발생될 수 있는 문제점을 해결할 수 있었으며, 유출계산 결과도 유량의 크기와 첨두시간 모두 관측값과 비교적 잘 맞는 것을 확인할 수 있었다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.4
• /
• pp.239-248
• /
• 2009

In this investigation, we observed surface morphology and porosity of a macroporous adsorbent made of Na-bentonite and Ca-bentonite as structure formation materials and grounded waste paper as macropore forming material for the development of a permeable reactive barrier to remove heavy metals in groundwater. Therefore, we selected minerals having higher cation exchange capacity among 2:1 clay minerals and other industrial minerals because sintering can significantly influence cation exchange capacity, resulting in drastic decrease in removal of heavy metals. The results showed that the increasing sintering temperature drastically decreased CEC by less than 10 % of the indigenous CEC carried by the selected minerals. One axial compressibility test results showed that the highest value was obtained from 5% newspaper waste pulp for both structure formation materials of Na-bentonite and Ca-bentonite although there were not much difference in bulk density among treatments. The pore formation influenced by sintering temperature and period contributes removal of heavy metals passing through the sintered macroporous media having different water retention capacity.

• Geophysics and Geophysical Exploration
• /
• v.15 no.4
• /
• pp.163-176
• /
• 2012

Effective porosity has been measured for cement specimen as a function of vacuum time and pressure in the vacuum saturation process. Six cement specimen are used; three of them are made of the same ratio of cement and sand, the other three are 100% cement mortar, of which average porosity is about 25% and 40%, respectively. Using the 6 samples, measured effective porosities are compared and examined with 5 different vacuum pressures (2, 4, 6, 8, 10 torr) and times (20, 40, 60, 80, 100 minute), respectively. Comparing measured effective porosity from experiments when vacuum time varies from 100 minute to 20 minute with 20 minute step and vacuum pressure is fixed to 10, 6, and 2 torr, average deviation decreases as 0.6, 0.5, and 0.2% respectively. Comparing measured effective porosity from experiments when vacuum pressure varies from 2 torr to 10 torr with 2 torr step and vacuum time is fixed to 100, 60, and 20 minute, average deviation increases as vacuum time decreases. These results can be a background of suggested method of ISRM that describes the vacuum time longer than 60 minute and vacuum pressure higher than 6 torr. In this study, only qualitative discussion can be possible for the effects on the effective porosity by decreasing 20 minute vacuuming time at the same pressure or by decreasing 2 torr of vacuum pressure at the same vacuum time. This is because the sample could not reached to perfectly dried condition even though the sample were dried at $105^{\circ}C$ and following the ISRM suggested method, so that initial water content could not be the same at each experiment.

• 한국해양학회지
• /
• v.25 no.1
• /
• pp.8-20
• /
• 1990

A series of pore water data were obtained during the different time over one year period between October 1987 and October 1988, from a site on a muddy intertidal flat, located in the Kyeong-gi Bay, west coast of Korea, The results have revealed that the tidal flat is an environment of active nutrient the subface supplied by the overlying seawater is almost completely removed from the pore water at depth of about 10 cm below the sediment surface. The nutrients such as ammonium and phosphate are produced through this process and subsequently accumulated in the pore water forming steep gradients near the sediment surface. Below the main sulfate redirection zone, a secondary peak of dissolved sulfate was often observed. Greal seasonal variation of the pore water nutrient profiles was observed, which was particularly clear in their maximum concentration as well as in their concentration gradient. The rate constants of sulfate reduction and nutrient regeneration, estimated by using a diagenetic model (Berner, 1980), differ by an order of magnitude between the summer and winter seasons. The difference in sediment temperature may account for most of the calculated variation. The C:N:P ratio, calculated from the pore water nutrient gradients also exhibits a slight seasonal difference. The organic matter being decomposed by sulfate reduction appears to be depleted in depleted in nitrogen, compared to the average marine organic matter.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.273-283
• /
• 1999

When microorganism is injected into porous medium such as soils, biomass is retained in the pore. Soil pore size and shape are varied from the initial condition as a result of biofilm formation which makes hydraulic conductivity reduced and friction rate between soil aggregates increased. In this research, hydraulic conductivity reduction was measured after microorganism are inoculated and cultured with synthetic substrate and nutrient. In addition, this research evaluated the applicability of biomass-soil mixture to the field condition as an alternative cover material in landfill by measuring hydraulic conductivity change after repetitive freeze-thaw cycles. Hydraulic conductivity of silty soil decreased by approximately 1/50 after biomass inoculation and cultivation. Biofilm attached on soil aggregates is resistant to acidic or basic condition. After repetitive freeze-thaw cycles, however, hydraulic conductivity increase implies that biomass clogging can be impaired.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2015.07a
• /
• pp.216-217
• /
• 2015

This study consist of research on the strength development properties of alkali activated slag(AAS) by differential combination of activators, initial protecting and curing conditions. 3 type of binders cured in the atmosphere, underwater and sealed were estimated compressive strength of 3, 7 and 28 days. Test results showed that strength development properties of binders varied with initial protecting and curing conditions because of ionized anions in pore water.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.622-627
• /
• 2019

This paper propose an initial rotor position detection method for sensorless operation of a single-phase permanent magnet synchronous motor(SP-PMSM) with asymmetric air-gap. In general, the sensorless control based on back-emf estimation is difficult to estimate the back-emf at the zero and low speed regions. For this reason, an open loop start-up technique is indispensable, and it is also necessary to detect the initial position of the rotor in order to rotate in a certain direction. In this paper, we propose a method to detect rotor polarity by adding offset voltage to high frequency voltage signal based on the magnetic characteristics of SP-PMSM. The validity and usefulness of the proposed algorithm are verified through several experimental results.

• Membrane Journal
• /
• v.30 no.2
• /
• pp.131-137
• /
• 2020

In this study, effect of inorganic particles on organic fouling was investigated by a laboratory-scaled pressurized membrane filtration. In order to cause organic fouling, sodium alginate (SA) was used as a feed solution. Regardless of the presence of inorganic SiO₂ particles, the complete pore blocking played an important role in determining the fouling rate during the initial period of membrane filtration. However, the formation of cake layer resulted in the membrane fouling more dominantly as filtration time progressed. In the presence of inorganic particles, both specific cake resistance and compressibility associated with the membrane fouling formed were relatively lower than that without SiO₂ particles. Membrane fouling was more severe at constant flux mode of filtration than that observed at constant pressure mode probably due to the concomitant increase of compressibility of fouling layer with transmembrane pressure (TMP). It was found that the presence of SA and SiO₂ particles in feed solution provided the synergistic effect on the hydraulic backwashing to reduce membrane fouling as compared to the SA solution alone without the inorganic particles.

• Korean Journal of Agricultural Science
• /
• v.7 no.2
• /
• pp.145-155
• /
• 1980

An engineering design of the machines and equipment for processing grain as well as an understanding of processing itself need the knowledge of thermal properties of grain. Thermal properties of grain are thermal conductivity, thermal diffusivity and specific heat. Knowledge of any two and the bulk density of grain enables the third to be calculated. Several workers have investigated these properties, with special emphasis on thermal conductivity and diffusivity. However, some information is available on the specific heat of rough rice and barley but it is available only for a foreign variety of grain and for as a function of moisture content only. The objectives of this study were to develop a model for the specific heat of rough rice and barley which were a staple products in Korea as a function of initial temperature, moisture content and porosity of grain with cooling curve method, and to analyze the effect of these factors on the specific heat of rough rice and barley. The results of this study are summarized as follows; 1. The specific heat was $1.8209-2.7041kJ/kg\;^{\circ}K$ for Naked barley, 1.8862-2.5625 k.l/kg K for Covered barley, $1.5167-2.3779kJ/kg\;^{\circ}K$ for Japonica rice and $1.5260-2.3981kJ/kg\;^{\circ}K$ for Indica rice. 2. The model for the specific heat of rough rice and barley as a function of initial temperature, moisture content and porosity of grain was developed. 3. Specific heat of rough rice was decreased with initial temperature, but specific heat of barley was increased with initial temperature. 4. On the whole specific heat of sample grain was increased with moisture content of grain. 5. Specific heat of the grain was found to decrease with porosity except Indica rice.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.1
• /
• pp.9-15
• /
• 2023

The cement is a typical CO₂ emission industry. Manufacturing process improvements and increased use of alternative materials are needed to reduce energy consumption and CO₂ emissions. This study confirmed the basic characteristics of cement hydration by sintering CAF at low temperature as a CO₂ adsorbent material. For the hydration product of the synthetic CAF, crystal phase analysis, porosity, and structural images were confirmed, and the compressive strength was measured. The replacement rate of SCAF was 10, 20, and 100 %, and the compressive strength tended to decrease as the replacement rate increased. In addition, when the SCAF substitution rate is 100 %, the hydration products of the early age are calcium aluminum oxide hydrate (Ca₃Al₂O₆ x H₂O) and calcium iron hydroxide (Ca₃Fe(OH)₁₂), and at substitution rates of 10 and 20 %, CAF compounds other than general cement hydrates brownmillerite was observed. As for the porosity, the pore size increased and the porosity increased with the increase of the replacement ratio. As a result of this study, CAF manufactured by low-temperature sintering seems to be difficult to use alone and general curing for utilization as a CO₂ adsorbing material.