• Electrical & Electronic Materials
• /
• v.6 no.5
• /
• pp.446-453
• /
• 1993

초기충진압력이 서로 다른 시편에 가한 가압횟수와 열처리시간의 혼합공정이 임계전류밀도 특성에 미치는 영향을 관찰하기 위하여 power-in-tube방법으로 초전도 선재를 제조하였다. 일정 초기충진압력에서 테이프화를 위한 열처리 및 가압이 혼합공정횟수가 증가할수록 임계전류밀도가 증가하였다. 초기충진압력이 1000kg/$cm^{2}$에서 Bi-2223 고온상 체적비가 가장 높게 나타났고 결정립이 판상으로 성장되었을 뿐만 아니라 C축과 직각방향으로 잘 배양되어 있음을 관찰할 수 있었다. 특히 초기충진압력 1000kg/$cm^{2}$의 시편을 두께를 줄이기 위하여 3회 가압하고 450시간 열처리하였을때 임계전류밀도가 5800A/$cm^{2}$를 나타내었으며 이를 중심으로 500, 2500kg/$cm^{2}$이 양측단으로 가우시안분포를 보였다. 결론적으로 시편의 임계특성은 적정 초기충진압력, Bi-2223 고온상 체적비, 테이프화를 위한 가압횟수, 결정의 일방향배열, 결정립의 성장등에 강하게 의존함을 알 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.94-99
• /
• 2003

For the assessment of combustion stability of a liquid rocket engine, a device called "Pulse Gun" should be developed first, which can induce artificial perturbations that may lead to excitations of pressure oscillations in a combustion chamber. A model chamber has been used for identifying design parameters of a pulse gun that defines its characteristics. Dynamic pressure measurements showed that shock waves generated from pulse guns are axisymmetric around the axis of a pulse gun barrel. Pressure waves perturbed by a pulse gun induce resonant acoustic frequencies of a model chamber. This fact indicates that successful pressure field perturbations of the KSR-III combustion chamber can be performed by a newly developed pulse gun device. A maximum value of dynamic pressure peaks measured at the opposite point against a pulse gun outlet becomes stronger as charge mass of pulse gun powder increases.

• Composites Research
• /
• v.20 no.4
• /
• pp.9-17
• /
• 2007

Powder metallurgy has been employed for the development of SiC particle reinforced aluminum metal matrix composites by means of hot isotropic pressing and vacuum hot pressing. A material model based on micro-mechanical approach then has been presented for the processes. Densification occurs by the inelastic flow of matrix materials during the consolidation, and consequently it depends on many process conditions such as applied pressure, temperature and volume fraction of reinforcement. The model is implemented into finite element software so that the process simulation can be performed enabling the predicted relative density to be compared with experimental data. In order to determine the performance of finished products, further tensile test has been conducted using the developed specimens. The effect of internal void of the materials on mechanical properties therefore can be investigated.

• Resources Recycling
• /
• v.7 no.4
• /
• pp.27-34
• /
• 1998

In this research, the processing control of NiCuZn Ferrite (NCZF) had been studied. NiCuZn Ferrite, which calcined at $700^{\circ}C$ for 3 bours, was ball milled for about 60 hours to ill김ke a size of $0.5\mu\;extrm{m}$ followed by granulation using spray dryer Apparent densincatioo rate and initial permeability of NiCuZn Ferrite with an initial packing density had been investigated as f follows. 1.The relative packing density of NCZF green body increas$\xi$d in the range of 48.6-56.8% with an increased forming pressure of 20-170 MPa. 2. The higher the relative pac퍼ng density of NCZF and the sintering temperature are, the higher the initial densification rate. The increased bulk rlcnsity of NCZF was attributed to the densification rate with decreased open pore and increased closed pore as the relative packing density, sintering temperature, and sinteriog tim$\xi$ increased. 3. The initial P permeability of NCZF with constant composition is logarithmically proportional to the bulk density of NCZF sintered at $875~925^{\circ}C$ for 0-5h, and strongly depended on the relative packing density of NCZF green body. The empirical equation is as f follows; log $\mu$i=$G1{\times}BD$+$G2{\times}RPD$+b(0);where, G1, G2; gradient, B.D: bulk density, RPD; relative packing density, b(0); intercept.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.89-89
• /
• 2003

로켓엔진의 연소에 필요한 추진제를 안정적으로 공급하기 위한 추진제 공급시스템의 주요 구성과 설계 주요 인자를 정리하였다 공급시스템은 추진제 주입/배출 장치, 추진제탱크 가압 및 배기 장치, 추진제 공급 주/분기 배관, 극저온 산화제 온도 유지 장치 등으로 구성되어 있다. 주요 설계 제한 조건으로는 터보 펌프 입구에서의 추진제 압력 및 온도, 필요 추진제 공급 유량 및 온도 그리고 추진제 충진 및 비상 배출 허용 시간 등이며 이는 각 로켓의 해당 임무에 따라 적절히 결정된다. 발사체로부터 할당된 중량값 이내에서 고신뢰도의 작동성, 안정성이 보장되는 시스템을 설계하여야 하며 초기 설계 단계에서 개발 및 수급 가능성을 동시에 고려하여야 할 것이다. 또한 고추력 생성을 위해 엔진 클러스터링이 수행되어야 할 경우 각 엔진으로의 균등한 추진제 배분 공급이 설계의 중요한 요구 조건이 된다. 이러한 공급시스템의 개념은 액체산소와 케로신 조합의 액체 로켓인 100kg급 소형 위성 발사체(KSLV-Ⅰ)에 적용될 예정이다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.1-8
• /
• 2004

A cylindrical constant volume combustion chamber was used to investigate the exhaust emission characteristics of homogeneous charge, stratified pattern and inhomogeneous charge under various conditions using gas chromatography. In the case of homogeneous charge condition, the $CO_2$ concentration is proportional to excess air ratio and overall charge pressure, the $CO_2$ concentration is proportional to excess air ratio and the UHC concentration is inversely proportional to ignition time and overall charge pressure. In the case of stratified pattern, the RI(rich injection) condition shows better exhaust emission characteristics, especially $CO_2$, than that of HI (homogeneous injection) or LI (lean injection) conditions. In inhomogeneous charge conditions, when initial charge pressure is increased, $CO_2$ and UHC concentration is reduced but $O_2$ concentration is increased. And when the excess air ratio of initial charge mixture is 3.0, UHC and $CO_2$concentration show lowest values.

• Korean Journal of Food Science and Technology
• /
• v.28 no.2
• /
• pp.324-329
• /
• 1996

In order to develop a novel dewatering process for soybean milk residue, hydraulic press with ohmic heating was built and its expression conditions were examined. The electric conductivity of raw soybean milk residue was 0.128 S/m and increased linearly with increasing temperature. Water content of the residue could be reduced to 74% with the conventional hydraulic press, but to less than 70% by applying ohmic heating to the hydraulic press. The most effective dewatering was achieved by applying alternative current with 5 kHz frequency at 60 V during expression. The solid content of the expressed liauid was markedly reduced from 10% to 3.3% by ohmic heating during expression. Temperature of the cake rose to above $95^{\circ}C$ during the dewatering due to ohmic heating.

• Economic and Environmental Geology
• /
• v.29 no.6
• /
• pp.677-687
• /
• 1996

The Buckchang deposits which is located in the Ockcheon metamorphic zone, are emplaced along $N20-30^{\circ}E$ trending fissure sets. So it is a sort of fissure-filling ore deposits. The results of mineral paragenetic studies suggest two stages of hydrothermal mineralization; stage I: base-metal sulfides stage, stage II: late base-metal sulfides, electrum and silver-bearing sulfosalts stage. The silver-bearing sulfosalts occured as the Buckchang mine are mainly argentite and, minor of canfieldite, tetrahedrite, etc. Au:Ag ratios of the electrums show a highly limited range of nearly 1:1 in atomic %. The temperature, salinity and pressure of the Buckchang deposits estimated from fluid inclusion and sulfur isotope studies are as follows; stage I: $174{\sim}250^{\circ}C$, 0.35~4.01 NaCl eq. wt.%, 0.40~1.00 Kbar, stage II: $138{\sim}222^{\circ}C$, 1.9~8.4 NaCl eq. wt.%, 0.22~0.53 Kbar. The estimated oxygen and sulfur fugacity during stage I mineralization, based on phase relation of associated minerals, range from $10^{-39.7}{\sim}10^{-44.7}$ atm. and $10^{-13.4}{\sim}10^{-18.1}$ atm., respectively. All these evidences suggest that the Buckchang deposits are polymetallic epithermal ore deposits.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.4
• /
• pp.69-78
• /
• 2022

Geotextile tubes are widely used to prevent erosion in coastal areas and to replace the backfill for shore slopes in the reclamation of land using dredged soil. In this study, The triaxial confining pressures were chosen as 10kPa, 50kPa, or 100kPa for the specimens reinforced with geotextile considering the condition in the site. The strain behavior under various compressive stresses was then identified. At strains 0% to 7%, the stress-strain behavior was the same due to the effect of initial strain hardening, in which the force was exerted according to the relaxation of the geotextile regardless of the confining pressure (≤100kPa). At strains of 7% or more, the specimen with the small confining pressure had smaller deformation under load, which increases the tensile resistance provided by the reinforcing geotextile. Brittle fracture was then observed due to strain softening and the deviator stress abruptly decreased. This is different from the phenomenon in which the shear strength increases as the confining pressure increases in general triaxial compression tests. In the geoxtile-confined tests, geotextiles are primarily subjected to tensile displacement. Thereafter, the modulus of elasticity increases rapidly, which exhibits the elastic behavior of the geotextile.

• Economic and Environmental Geology
• /
• v.25 no.3
• /
• pp.233-243
• /
• 1992

Ore mineralization of the Hwanghak copper deposit in the Ogsan area occurred in three stages of quartz (stage I and II) and calcite (stage III) veining along fissures in Early Cretaceous sedimentary rocks. Ore minerals are pyrite, pyrrhotite, chalcopyrite (dominant), sphalerite, hematite, galena, and Ag-, Pb-, and Bi-sulfosalts. These were deposited during the first stage at temperatures between $370^{\circ}C$ and < $200^{\circ}C$ from fluids with salinities between 0.5 and 7.6 equiv. wt. % NaCl. There is evidence of boiling and this suggests pressures of less than 180 bars during the first stage. Equilibrium thermodynamic interpretation accompanying with mineral paragenesis and fluid inclusion data indicates that copper precipitation in the hydrothermal system occurred due to cooling and changing in chemical conditions ($fs_2$, $fo_2$, pH). Gradual temperature decrease from $350^{\circ}$ to $250^{\circ}C$ of ore fluids by boiling and mixing with less-evolved meteoric waters mainly led to copper deposition through destabilization of copper chloride complexes. Sulfur isotope values of sulfide minerals decrease systematically with paragenetic time from calculated ${\delta}^{34}S_{H_2S}$ values of 8.2 to 4.7‰. These values, together with the observed change from sulfide-only to sulfide-hematite assemblages and fluid inclusion data, suggest progressively more oxidizing conditions, with a corresponding increase of the $sulfate/H_2S$ ratio of hydrothermal fluids. Measured and calculated hydrogen and oxygen isotope valutls of ore-forming fluids suggest meteoric water dominance, approaching unexchanged meteoric water values.