• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.705-706
• /
• 2010

The design analysis for the ignition transient combustion characteristics of a Kick Motor igniter indicated that the initial pressure condition would delay ignition time within a range from 100 to 500 ms. In the development tests, we confirmed that the igniter could provide the acceptable energy to ignite the main propellant at ignition transient.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.138-141
• /
• 2010

A study to reduce the ignition peak pressure of gas generator for the missile launching system was accomplished. The igniter, as the energy release device for igniting the propellant, is aimed at simultaneous ignition of bundled 3-layered propellant grain without unstable burning. In case of our gas generator which must use the double-base propellant with low ignition property, the fast ignition of propellant and reduction of initial peak pressure should be required for the satisfaction of ejection velocity and acceleration condition. By applying MTV ignition charge for the igniter of gas generator, we accomplished all system performance requirements.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.814-819
• /
• 2017

The objective of this paper is to observe effects of an ignition position and time on the ignition transition. A gaseous oxygen and liquid kerosene are used for propellants with the shear-coaxial injector. In order to study the ignition delay time and combustion instability intensity, the pressure transducer was used. The ignition position was changed with the injector spacer. Sequences except the igniter operation time were fixed to compare the ignition time only. Initial pressure peak and ignition delay time increased as the ignition time was delayed. Also, the unstable flame development zone was detected as the igniter was away from the injector.

• Journal of Energy Engineering
• /
• v.4 no.1
• /
• pp.85-94
• /
• 1995

본 연구에서는 최근 차량용 대체연료로서 주목받고 있는 천연가스의 연소특성을 규명하기 위해 밀폐된 정적연소실을 이용, 당량비, 초기압력 및 점화위치 변화에 따른 연소실험을 행하였으며, 그 결과 다음과 같은 결론을 얻었다. 메탄-공기 예혼합기의 화염전파과정은 이론혼합기 부근에서 구면형으로 진행되는데 반해, 과농 또는 과박 혼합기 그리고 점화위치가 연소실 벽면에 가까울수록 타원형으로 진행되며, 초기압력이 증가함에 따라 화염전파는 느려진다. 화염전파속도와 연소 속도는 초기압력이 낮고 점화위치가 연소실 중심에 가까울수록 빠르며, 당량비 1.0∼1.1 사이에서 최대치를 보인다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2376-2384
• /
• 1992

A theoretical analysis is carried out to predict the characteristics of transient ignition phenomena for the spherical fuel droplets cloud with non-uniform droplet size and number density distribution. Numerical calculations are performed for various cases depending on the combinations of the major parameters such as ambient temperature and initial distributions of droplet size and number density. The results of present study show that the ignition delay decreases for higher ambient temperature and smaller droplet size. Droplets cloud of hollow type with outer concentrated distribution ignites most rapidly.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2010.04a
• /
• pp.59-63
• /
• 2010

Seven different size of orifice were applied in a constant volume combustion chamber for evaluating the effects of torch-ignition on combustion. The initial flame development and flame propagation were analyzed by the mass fraction burn and combustion enhancement rate. The combustion pressures were measured to calculate the mass fraction burn and the combustion enhancement rates. In addition, the flame propagations were visualized by the shadowgraph method for the qualitative comparison. The result showed that the combustion pressure and mass burned fraction were increased when using the torch-ignition device. The combustion enhancement rates of torch-ignition cases were improved in comparison with conventional spark ignition. Finally, the visualization results showed that the torch-ignition induced faster burn than conventional spark ignition due to the earlier transition to turbulent flame and larger flame surface, during the initial stage.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.953-961
• /
• 2011

A numerical model of the igniter for the interior ballistics has been developed combining the lumped parameter model with the theoretical equation of the orifice. With the developed model of the igniter, the numerical study on characteristics of the interior ballistics according to the igniter configuration in terms of the igniter length, the side hole diameter, and the distribution of side holes has been conducted. As results of the calculation of the pressure difference between the breech and shot base, the low frequency oscillations have been influenced by the igniter length, while the high frequency oscillations have been affected by the side hole diameter and the distribution of side holes.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.105-113
• /
• 2013

A numerical model of the igniter for the interior ballistics has been developed by combining lumped parameter model with the theoretical equation of orifice. With the developed model of the igniter, the numerical study on characteristics of the interior ballistics has been conducted according to the igniter configuration in terms of igniter length, side hole diameter, and distribution of side holes. As results of the calculation of the pressure difference between the breech and shot base, the low-cycle oscillations have been influenced by the igniter length, while the high-cycle oscillations have been affected by the side hole diameter and the distribution of side holes.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.106-109
• /
• 2012

It was designed and tested ignition that an oxidizer rich preburner for a staged combustion cycle liquid rocket engine propelled by kerosene and LOx. Operation conditions of the preburner are about 60 of OF ratio and 20 MPa of combustion pressure. Ignition characteristics were compared by propellants flowrate. As the results, the higher propellants flowrate, the shorter the ignition delay time and the higher ignition stiffness. The ignition delay time was affected by incoming the oxidizer flowrate through the refrigerative cooling channels. The oxidizer flowrate from the cooling channels decreased by inflow of combustion gas during initial ignition. The oxidizer flowrate of the cooling channels increases, it is rapid recovery by cooling effect, eventually the ignition delay time decreases.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.4
• /
• pp.85-90
• /
• 2018

The objective of this paper is to observe effects of ignition position and time on ignition transition. A gaseous oxygen and liquid kerosene mixture is used as propellant with a shear-coaxial injector. In order to study the ignition delay time and combustion instability intensity, the pressure transducer was used. Sequences, excepting igniter operation time, were fixed to compare the ignition time only. Initial pressure peak and ignition delay time increased as the ignition time was delayed. Additionally, an unstable flame development zone was detected when the igniter was away from the injector.