• Proceedings of the Acoustical Society of Korea Conference
• /
• 1992.06a
• /
• pp.96-99
• /
• 1992

섬유강화 복합재료의 동탄성계수와 감쇠특성을 규명하기 위하여 랜덤하게 분포된 무한 실린더 형상의 산란체를 가진 매질내에서, 조화운동을 하는 압축 및 SV탄성파의 전파에 관하여 연구하였다. 단일 실린더에 대한 산란계수로부터 La의 준결정근사법을 이용하여 다중산란에 관한 이론을 유도하였고, 매질내에서의 파동전파 특성을 내포하는 분산관계식을 얻었다. 수치적으로 분산관계식의 해를 구함으로써 2 차원 유효체적강성, 횡방향 유효전단강성 및 각 파동의 전파에 따른 감쇠계수를 주파수와 체적비의 함수로서 제시하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.187-197
• /
• 2004

This paper presents the effects of cylinder shell elasticity on effective bulk modulus of oil $K_e$ in automotive hydraulic dampers. A theoretical model of cylinder shell bulk modulus $K_c$ based on the elasticity theory of thick-walled cylinder incorporating not only radial but longitudinal deformation is proposed. In a cylinder, values of $K_c$ by the new model and traditional models are computed and the discrepancies among them are discussed. In a twin-tube type automotive damper, the variation of $K_e$ under different pressure values in chambers of the damper cylinder, based on different theoretical models for $K_c$ is computed. Through these computations, it is shown that remarkable discrepancies in computed values of $K_e$ might occur according to the $K_e$ models in connection with $K_c$ models.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.54-60
• /
• 2008

In the trackbed design using elastic multilayer model, the stress-dependent resilient modulus $(E_R)$ is an important input parameter, that is, reflects substructure performance under repeated traffic loading. However, the evaluation method for resilient modulus using repeated loading triaxial test is not fully developed for practical purpose, because of costly equipment and the significantly fluctuated values depending on the testing equipment and laboratory personnel. The this study, the paper will present an indirect method to estimate the resilient modulus using dynamic properties. The resilient modulus of crushed stone, which is the typical material of sub-ballast, was calculated with the measured dynamic properties and the range of stress level of the sub-ballast, and approximated with the power model combined with bulk and deviatoric stresses. The resilient modulus of coarse grained material decreases with increasing deviatoric stress at a confining pressure, and increases with increasing bulk stress. Sandy soil (SM classified from Unified Soil Classification System) of subgrade was also evaluated and best fitted with the power model of deviatoric stress only.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.471-478
• /
• 2002

초음파를 사과의 비파괴 품질판정에 이용하기 위한 기초연구로서 계측된 저장기간에 따른 사과의 초음파 특성과 본 연구에서 계측된 사과의 기계적 특성을 이용하여 초음파에 의한 사과의 탄성계수 및 생물체항복강도 예측모델을 개발하고자 하였으며, 결론은 다음과 같다. 1. UTM을 이용하여 사과의 기계적 특성치를 분석하여 생물체항복점, 생물체항복변형량, 생물체항복강도, 파괴점, 극한변형량, 극한강도 및 탄성계수 등을 구하였다. 2. 사과의 기본 물성, 초음파 특성과 기계적 특성값 들을 분석한 결과 사과의 질량, 체적, 시간영역의 진폭(PTP), 제3영역 에너지 스펙트럼 밀도함수가 기계적 특성 중 생물체항복강도, 탄성계수와 높은 상관성이 있는 것으로 나타났다. 3. 사과의 저장 기간, 질량, 체적, Peak-to-peak, 제3영역의 에너지값 등 5개의 독립변수를 가지는 다중선형회귀모형으로 사과의 탄성계수 및 생물체 항복강도 예측모형을 개발하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.8
• /
• pp.711-718
• /
• 2011

The thermoelastic behavior of the porous carbon/phenolic composites is studied using the thermomechanical response model of chemically decomposing composites. The model includes thermal dependence of the porous composites, porosity in the pyrolysis process, pore pressure due to decomposing gases, and shrinkage. The poroelastic coefficients are calculated based on representative volume element model and finite element analysis. The internal stress distribution caused by pores and pore pressure, and the overall deformation are verified. The effects of the poroelastic coefficients on the thermoelastic behavior are examined through numerical experiments.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.115-121
• /
• 2010

To evaluate the engineering characteristics of aggregate base materials, cyclic triaxial, CBR and permeability tests were performed for 15 samples. The CBR values of aggregate base materials have wide range from 32 to 110(average 81) and the amount of swelling in submerged conditions has below 0.04mm. The Modulus of aggregate base materials were significantly affected by volumetric stress, linear volumetric model was best for fitting. The modulus of aggregate base materials were determined within range of 100MPa~600MPa, 80~270 and 0.1~0.6 for model coefficient $k_1$ and $k_2$ respectively. The empirical correlation model was suggested that prediction the modulus from the basic properties obtained from particle size distribution test and compaction test. The coefficient of determination of the proposed correlation model was 0.423 for model coefficient $k_1$, 0.920 for model coefficient $k_2$ and 0.872 for modulus with stress level.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.309-315
• /
• 2000

For proper sampling of a rock and preparation of specimens, the representative elementary volume (REV) should be determined in rock mechanical test and numerical analysis. Mechanical properties of a rock, in general, would be strongly affected by mineral composition. In this reason REV of Youngju granite is determined by using stereoscopic microscope observation and homogenization numerical analysis. As the area of analysis model exceeds approximately 702$\textrm{mm}^2$(900 elements), the change of the mineral composition is not observed. The calculated results indicate that Young's modulus is fluctuated with increase of the number of elements in homogenization numerical analysis mesh. However, as the number of elements exceeds 1156 (area of about 900$\textrm{mm}^2$), Young's modulus does not change apparently.

• Economic and Environmental Geology
• /
• v.56 no.1
• /
• pp.13-21
• /
• 2023

X-ray powder diffraction study was conducted on the bulk modulus and phase transition behavior of synthetic zeolite X under high temperature and high pressure. Water and HCO₃^- solution were used as a PTM. Sample was heated and pressurized up to 250 ℃ and 5.18 GPa. The change of unit cell volume and phase transition were observed by X-ray diffraction. The lattice constants and unit cell volume of zeolite X, gmelinite, natrolite, and smectite were calculated using the GSAS2 program to which Le Bail's whole powder pattern decomposition (WPPD) method was applied. The bulk modulus of each zeolite X and smectite were calculated using the EosFit program to which the Birch-Murnaghan equation was applied. The bulk modulus of zeolite X is 89(3) GPa in water run, and zeolite X is 92(3) GPa in HCO₃^- solution run. In both run, pressure induced hydration (PIH) occurred due to the inflow of PTM into the zeolite X framework at initial pressure. Zeolite X transited to gmelinite, natrolite, and smectite in water run. Zeolite X, however, transited to smectite in HCO₃^- solution run. Interzeolite transformation occurred in water run, and did not occur in HCO₃^- solution run, which is assumed that conflict between the environment to form zeolite and the pH of the HCO₃^- solution.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.827-838
• /
• 1994

Numerous pavement response models rely on constitutive relationships to describe the response of granular materials. In this study, a nonlinear elastic constitutive model which is a function of bulk stress and octahedral shear stress is proposed to describe the resilient behavior of thick granular base courses under flexible airfield pavements. Special features of this model are its accuracy to predict the nonlinear resilient behavior, its simplicity to determine the material constants and its ability to model the secondary effect of decreasing the resilient modulus due to shear effects. In laboratory tests, the nonlinear resilient behavior of granular materials is investigated and values of resilient moduli are determined to provide data for verifying the proposed model. It is found that the resilient modulus is much more dependent on the states of stresses in terms of bulk stress and deviator stress than any other factors. Result of comparison shows that predicted values of resilient moduli are in good agreement with the measured values indicating that the proposed model is suitable to describe the nonlinear resilient behavior of the granular material with wide range of stress states which meet in airfield pavements.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.111-117
• /
• 1999

섬유강화 복합재료의 섬유와 수지까지 세부적으로 모델링이 가능한 Direct Numerical Simulation을 통해서 Boron/Aluminum 섬유강화 복합재료의 탄성계수들을 구해 보았다. 수치실험에서는 복합재료를 직교이방성 물질로 가정하였고, 특정 체적에 대한 평균치를 이용해서 물성치를 구하였으며, 혼합법칙에 의해서 구한 값 및 대표체적요소(Representative Volume Element)를 사용해서 구한 값들과 비교하였다. 혼합법칙의 경우, 섬유방향 인장계수(E₁)을 제외한 나머지 물성치들에 대해서는 상당한 차이를 나타내며, 이는 혼합법칙 유도과정에서 가정한 기본가정들이 적절하지 않기 때문이라는 것을 수치실험(Numerical Experiment)을 통해 알 수 있었다.