• Tribology and Lubricants
• /
• v.12 no.2
• /
• pp.32-40
• /
• 1996

The tribological role of copper alloy fine particles in an additive is not well known compared to solid lubricants such as $MoS_{2}$ and PTFE. In this experimental investigation, a series of friction and wear test was undertaken to gain a better understanding of an additive containing copper alloy fine particles and to identify the effectiveness of copper alloy particles in improving tribological performance of the lubricant. Friction and wear of specimens under lubricated contact condition were studied and the worn surfaces were characterized by AES (Auger Electron Spectroscopy), SEM (Scanning Electron Microscopy) and optical microscopy. It was revealed that a copper-contained layer was formed and this layer resulted in considerable reduction in both friction and wear due to its lubricity and anti-wear property. The analysis of worn surface revealed that copper of the fine alloy particles in the additive helps healing the worn surface by plating and filling wear pits.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.59-64
• /
• 2002

The effects of EGR on emissions were investigated by using a six-cylinder, 8 litre, turbo-charged, heavy-duty diesel engine with a low pressure route EGR system. The experiments were performed at various engine loads while the EGR rates were set from 0% to 30%. Hot and cooled EGR are achieved without cooling and with cooling respectively. To verify the possibility of EGR technology for the applications, test were performed with steady state test cycle. It was found that the exhaust emissions with the EGR system resulted in a very large reduction in oxides of nitrogen at the expense of higher smoke and PM emissions. Increasing the EGR rate leads to deteriorating specific fuel consumption and power at lower speed and higher load. Also, the reduction rates of NOx emissions for hot and cooled EGR are similar.

• Journal of Environmental Health Sciences
• /
• v.22 no.4
• /
• pp.55-61
• /
• 1996

Measurements of the seasonal variations of concentration and size distribution of TSP, $SO_4^{2-}, NO_3^-, Cl^-, NH_4^+, Na^+, K^+, Ca^{2+}$ and $Mg^{2+}$ were made by Andersen air sampler from May 1995 to April 1996 in Seoul. The size distribution of these ions was divided into four patterns. 1) Distribution was concentrated on fine particles over a year such as $NO_3^-$ component, 2) Distribution was predominated in coarse particles fraction over a year such as $Mg^{2+}$ and $Ca^{2+}$ components, 3) Distribution was differerent from various seasons such as $NH_4^+, SO_4^{2-}, Cl^-$ and $K^+$ components, 4) Distribution was bi-modal such as $Na^+$.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.261-264
• /
• 2015

Soot particles of diesel and bunker-A with different sulfur contents were generated by pyrolysis with varying conditions of fuel flow rate and residence time in the ceramic tube at $1300^{\circ}C$. TEM and particle size analyzer were used for analysing the primary and the secondary particle size distributions. The results showed that the sulfur content in fuel influences soot inception while the fuel concentration and residence time affects the growth of incepted soot particles.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.257-260
• /
• 2015

Light extinction characteristics of soot particles in ethylene and propane inverse diffusion flames have been experimentally investigated. The measured data suggested that the refractive index of soot particles varies with light wavelength due to PAH contents existing during the soot growth process. The results showed that the scattering effect is less important as the size of secondary particles rarely affects the optical properties of the soot even when the size is large enough to deviate from Rayleigh assumptions.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.5-8
• /
• 2013

The ignition of aluminum particles under high pressure and temperature conditions is studied. The laser ablation method is used to generate aluminum particles exposed to pressures ranging between 0.35 and 2.2 GPa. A continuous wave $CO_2$ laser is then used to heat surface of the aluminum target until ignition is achieved. We confirm ignition by a spectroscopic analysis of AlO vibronic band of 484 nm wavelength. The radiant temperature is measured with respect to various pressures for tracing of required heating energy for ignition. Then the ignition temperature is deduced from the radiant temperature using the thermal diffusion equation. The established ignition criteria for corresponding temperature and pressure can be used in the modeling of detonation behavior of heavily aluminized high explosives or solid propellants.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.680-689
• /
• 1996

SrCaCuO와 BiPbCuO 화합물로 이루어진 이중층시료가 만들어 졌으며, 소결과정에서 나타나는 확산과 입자간의 상호작용으로 108K의 임계온도를 나타내었다. 이 시료는 820.deg. C에서 0-210 시간동안 소결되었다. 초전도체의 생성, 성장메카니즘과 임계온도의 관계가 연구되었으며, 최적조건은 820.deg. C에서 210시간 소결하고 SrCaCuO와 BiPbCuO의 도포비가 1:0.6인 시편에서 나타났다. 또한 이중층시료에서 가장 좋은 조성비는 S $r_{2}$C $a_{2}$C $u_{2}$ $O_{x}$와 B $i_{1.9}$P $b_{0.5}$C $u_{3}$ $O_{y}$ 이었다.다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.393-396
• /
• 2005

This paper is concerned with the drawing process of $Al-1\%Si$ bonding wire. In this study, the finite-element model established in previous work was used to analyze the effect of various forming parameters, which included the reduction in area, the semi-die angle, the aspect ratio, the inter-particle spacing and orientation angle of the fine Si particle in drawing processes. The finite-element results gave the consolidation condition. From the results of analysis, the effects of each forming parameter were determined. It is possible to obtain the Important basic data which can be guaranteed in the fracture prevention of $Al-1\%Si$ wire by using FE-Simulation.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.64-64
• /
• 2011

머드는 알루미늄, 철, 마그네슘 등의 미네랄이 풍부하여 원적외선 방사율이 높고, 미량 포함된 단백질과 비타민은 피부의 세포조직을 강화하고 탄력성을 주며, 항균, 소취 등의 기능을 보유하고 있다. 이러한 유익한 기능을 가진 머드를 매일 사용하는 면타올에 적용하려 하나 무기 염재인 머드는 섬유와 친화성이 없어 일반 염료처럼 고농도로 섬유에 염색되지 못하고 있다. 본 연구에서는 섬유의 촉감에 영향을 미치지 않으면서 머드의 염색농도를 높이기 위해, 4종의 고착제를 이용한 염색법을 검토하였다. 먼저 식물성 단백질액으로 면타올을 전처리하고 나노입자의 머드액를 사용하여 염착시킨 경우가 가장 진하게 염색되며, 염색견뢰도 측정 결과 세탁과 땀에 모두 우수한 것으로 나타났다.

• Proceedings of the KAIS Fall Conference
• /
• 2008.05a
• /
• pp.319-322
• /
• 2008

본 논문은 미분 반응기 및 유동층반응기에서 메탄의 열분해에 의한 수소 생산과 탄소 생성에 대한 연구를 수행하였다. 일반적으로 고온 분해시 사용되는 니켈과 철 성분을 대신할 철광석을 이용하여 분해특성을 고찰하였다. 환경에 대한 영향을 최소화한 상태에서 메탄의 전환반응을 메탄 분해촉매 활성에 영향을 미치는 인자에 대하여 연구하였다. 측정된 압력요동특성치의 해석을 통하여 유동층 열분해촉매의 유동화현상을 측정하였으며, 유동화특성에 따른 메탄열분해능을 측정하였다. 또한 고정층에서 공간속도, 입자크기, 비표면적이 미치는 영향을 고찰하여 철광석의 사용가능성을 타진하였다.