• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.56-62
• /
• 2008

This study presents the aerodynamic design and numerical analysis results on a transonic centrifugal compressor which is used for gas turbine systems. Mean-line analysis and quasi-3D analysis are used for the aerodynamic design, and Reynolds-averaged Navier-Stokes analysis is applied to flow analysis of the compressor. The aerodynamic parameters for a transonic compressor, such as pressure coefficient, swirl parameter, blade loading, are discussed, and flow characteristics in the impeller and diffuser are discussed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.2
• /
• pp.152-160
• /
• 2008

In the present paper, a transonic mixed-flow compressor that has relatively lower frontal area than that of centrifugal compressors is discussed, and aerodynamic design as well as performance prediction are performed. Main design constraints are compressor exit Mach number of 0.3 and flow angle of 30degrees at the design point, and maximum overall compressor diameter of 177mm, that is 7.0inch. The mass flow rate of design point and pressure ratio are 1.05kg/s and 5.2:1, respectively. The aerodynamic design results show that the transonic compressor designed with forward-swept inducer and curved diffuser can have the target performance with efficiency of 75% within the given constraints. And the compressor exit flow characteristics are discussed here.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.2
• /
• pp.8-15
• /
• 2001

In the continuing quest for increased turbomachinery efficiency, the part played by blade profile shape remains crucial. The application of a heated thin metallic film with CTA(constant temperature anemometer) to the measurements of the laminar and turbulent boundary layer behavior(shock-boundary layer-interaction) in a transonic wind tunnel. Results of measurements with hot-film sensors on transonic compressor blades are extremely difficult to interpret because of ambiguous probe signals due to the complexity of the local flow pattern. In order to get the explicit information and give the designer to interpret characteristic signals from hot-film probes, a method was developed by comparing the results with other measuring technic results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.4
• /
• pp.317-326
• /
• 2008

The main purpose of the present study is to perform shape optimizations of transonic compressor blade in order to enhance its performance. In this study, the Latin hypercube sampling of design of experiments and the weighted average surrogate model with the help of a gradient based optimization algorithm are used within design space by the lower and upper limits of each design variable and for finding optimum designs, respectively. 3-D Reynolds-averaged Navier-Stokes solver is used to evaluate the objective functions of adiabatic efficiency and pressure ratio. Six variables from lean and airfoil thickness profile are selected as design variables. The results show that the adiabatic efficiency is enhanced by 1.43% by efficiency optimization while the pressure ratio is increased very small, and pressure ratio is increased by 0.24% by pressure ratio optimization.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.1
• /
• pp.9-19
• /
• 2017

In this study, stator shroud injection in a single-stage transonic axial compressor is proposed. A parametric study of the effect of stator shroud injection on aerodynamic performances was conducted using the three-dimensional Reynolds-averaged Navier-Stokes equations. The curvature, length, width, and circumferential angle of the stator shroud injector and the air injection mass flow rate were selected as the test parameters. The results of the parametric study show that the aerodynamic performances of the single-stage transonic axial compressor were improved by stator shroud injection. The aerodynamic performances were the most sensitive to the injection mass flow rate. Further, the total pressure ratio and adiabatic efficiency were the maximum when the ratio of circumferential angle was 10％.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.74.2-74.2
• /
• 2005

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.3 s.36
• /
• pp.7-13
• /
• 2006

Shape optimization of a rotor blade in a single-stage transonic axial compressor has been performed using a response surface method and three-dimensional Navier-Stokes analysis. Two shape variables of the rotor blade, which are used to define a blade skew, are introduced to increase an adiabatic efficiency. Throughout the shape optimization of a rotor blade, the adiabatic efficiency is increased to about 2.2 percent compared to that of the reference shape of the stator. The increase in efficiency for the optimal shape of the rotor is due to the pressure enhancement, which is mainly caused by moving the separation position on the suction surface of rotor blade to the downstream direction.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.228-231
• /
• 2008

Flow fields of a transonic centrifugal compressor are calculated using the commercial CFD code, CFX-TASCflow. Due to the transonic inlet condition, interactions between the shock wave and boundary layers and between the shock wave and tip leakage vortices generate complex flow structures and extra losses. The calculated results show that strong secondary flows due to high curvature and high rotational speed of the impeller. And streamlines near suction surface show that strong radially upward flow develops after the shock between the leading edge locations of main blade and splitter.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.639-645
• /
• 2003

Design optimization of a transonic compressor rotor (NASA rotor 37) using response surface method and three-dimensional Navier-Stokes analysis has been carried out in this work. Baldwin-Lomax turbulence model was used in the flow analysis. Two design variables were selected to optimize the stacking line of the blade, and mass flow was used as a design variable, as well, to obtain new design point at peak efficiency. Data points for response evaluations were selected by D-optimal design, and linear programming method was used for the optimization on the response surface. As a main result of the optimization, adiabatic efficiency was successfully improved, and new design mass flow that is appropriate to an improved blade was obtained. Also, it is found that the design process provides reliable design of a turbomachinery blade with reasonable computing time.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.5
• /
• pp.84-87
• /
• 2009